Alpine iLX-702D User manual

Update Instructions
Precautions ...................................................................... 2
Performingtheupdate .................................................... 2
Alpine rmware version 5.000
Contents
Firmware Overview
Introduction
Firmware information ................................................... 2
Requirements and limitations ...................................... 2
Calibration Status ........................................................... 2
Volume Operation .......................................................... 3
Mute Icon ......................................................................... 3
Momentum scroll ........................................................... 3
Keyboard Operation ....................................................... 3
Search function ............................................................... 3
Folder Up/Down ............................................................. 3
Mute while backing up ................................................... 4
Guide adjustment ............................................................ 4
Camera display ................................................................ 4
Parking support (front camera connected) ................... 4
Parking support (front camera not connected) ............ 5
1
Navigation ............................................................................. 2
Sound .................................................................................... 3
Graphical User Interface ..................................................... 3
Camera Operation and Features ........................................ 4
Features

7Once the update has completed, the Alpine unit will reset.
To check that the update was applied successfully follow the steps below.
Features
Update Instructions
Firmware Information
Precautions
Navigation
is Firmware update is specically intended for users with the Alpine
X208AU / INE-W977A/ iLX-702D. ere is one rmware update per
unit. If you are unsure if you need this update please contact your
nearest Alpine dealer.
Please note: e update is not required for Alpine units
with Firmware versions 5.0000 or higher
•Do NOT switch o the vehicle / switch o the unit’s power nor remove
the USB ash drive during the update process.
•Do NOT use compressed zip-les for update and do NOT change le
names.
•Do NOT store any other folders and les on the USB stick
•Do NOT operate the Alpine unit whilst updating nor update the Alpine
unit while driving
• e unit is updated via USB connection. Plug in the USB ash drive
into the USB socket of the Alpine unit to initialise the update
1Ensure that the correct correct le is used to perform the update.
the product codes are listed below;
2Un-zip the downloaded folder into the root directory of the USB
ash drive
3Turn the vehicle on and plug in the USB ash drive into the USB
socket of the Alpine unit.
4Once a prompt appears on the screen, press OK.
5Press OK to conrm and initialise the update.
6e update will take approximately 4 minutes to complete.
Navigation calibration/status can be viewed to allow deeper analysis
of the speed signal, GPS reception and leanring status of the vehicle
positioning
e reset button executes a reset of all navigation settings including the
GPS/GLONASS module
Introduction
Requirements and limitations
Performing the update
• Windows XP / Windows 7 / Windows 8 / Windows 10
• USB ash drive with a minimum capacity of 1 GB
X208AU NP00003A
INE-W977A NP00004A
iLX-702D RE00010A
Calibration status
SETUP GENERAL GENERAL ABOUT
2

Alphanumeric Special characters Symbols
Shi key added to the keyboard to choose between lower-case and
upper-case letters
!?# key will now operate through a toggle function.
A
Two swipe function to view PTY in the radio source is removed and
replaced with a so-key to reduce the amount of steps required to view
PTY options
Two swipe function to search within the USB/Bluetooth sources is
removed and replaced with a so-key to reduce the amount of steps
required to view options
Search Function
Folder Up/Down
Sound
Audio, navigation, voice recognition/Siri, and hands free telephone
(HFT) volume can be operated individually.
To control these volume sources, press the - or + keys while they are
active.
Momentum scrolling is added to intuitively browse through menus
quicker and more eciently.
Folder up/down key added to the USB source to toggle through music/
video folders.
When active, the mute icon will ash on the top le status bar for the
users reference.
Radio
USB/Bluetooth
Volume Operation
Momentum Scroll
Keyboard Operation
Mute
Graphical User Interface
a
3

Camera Operations and Features
Mute while backing up
Guide adjustment
Camera display
Parking support (front camera connected)
Audio can be muted while in reverse as a safetyfunction to improve user
concentration.
Long-push integration of guide adjustment provides users a faster way
of adjusting the camera guidelines to suit their specic vehicle
Users can display the rear camera at anytime with the camera so-key
located in the main menu.
Using a KCX-C250MC multi-camera selector interface, parking support
is added to view the front camera automatically (for 10 seconds or until
the vehicle has travelled over 16kms/hr) once reverse is disengaged.
SETUP GENERAL SOUNDS MUTE WHILE BACKING UP
Note that if integrating an OEM camera where the voltage is controlled
by an active reverse gear, it must be re-wired to a 12V accessories
source.
Note that if integrating an OEM camera where the voltage is controlled
by an active reverse gear, it must be re-wired to a 12V accessories
source.
Once reverse is engaged, the rear camera will be active.
Once reverse is disengaged, the Alpine unit will display the front camera
image for 10 seconds or until vehicle exceeds 16kms/hr
e Alpine unit will revert back to the last source aer the 10 seconds
has passed or vehicle exceeds 16kms/hr
4

Parking support (front camera not connected)
If a front camera is not connected, the Alpine unit will delay the reverse
camera image for 10 seconds or until the vehicle has travelled over
16kms/hr) once reverse is disengaged.
Once reverse is engaged, the rear camera will be active.
Once reverse is disengaged, the Alpine unit will delay the rear camera
image for 10 seconds or until vehicle exceeds 16kms/hr
e Alpine unit will revert back to the last source aer the 10 seconds
has passed or vehicle exceeds 16kms/hr
5