Alto 1700 User manual

Form No. 70127B 11/00 CLARKE TECHNOLOGY Printed in the U.S.A.
READ THIS BOOK
This book has important information for the use and safe operation of this machine. Failure to read
this book prior to operating or attempting any service or maintenance procedure to your ALTO
machinecouldresultininjurytoyouortootherpersonnel;damagetothemachineortootherproperty
could occur as well. You must have training in the operation of this machine before using it. If your
operator(s) cannot read English, have this manual explained fully before attempting to operate this
machine.
All directions given in this book are as seen from the operator’s position at the rear of the machine.
For new books write to: ALTO U.S. INC., 2100 Highway 265, Springdale, Arkansas 72764.
Operator's
Manual ULTRA SPEED
BURNISHER
1700

Page - 4 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700
19" (48cm) 3M Burnishing Pad Selection Chart
PartNo. Description Application Use RPM Color Finish
976289 Top Line Burnish Dry 1500-3000 Peach Hard finish/high traffic
Soft finish/low traffic
976326 Natural Blend Burnish Dry 1500-3000 OffWhite Hard finish/high traffic
Soft finish/low traffic
High traffic/low
Maintenance
976235 UHS Tan Burnish Dry 1500-3000 Tan Hard finish/high traffic
Buffer Wet-look hard finish
976236 UHS Aqua Burnish Dry 1500-3000 Aqua Soft finish/low traffic
Buffer Wet-look soft finish
976234 SHS Buffer Buff Dry/Spray 600-1500 Beige Glossy finish
Spray
Thedirectdriveelectricburnishersarefloorpolishingmachines.Theyareoperatedbymovingthemforwardand
backward across the floor. Note: Do not use the machine for wet scrubbing.
FEATURES AND SPECIFICATIONS
CAUTION: Topreventseriousdamagetothefloorsurface,makesurethemachineisalwaysmovingforward
or backward when the pad driver is in contact with the floor.
Specifications
OPERATORSAFETYINSTRUCTIONS(cont.)
WARNING: To avoid injury keep hands, feet and loose clothing away from all moving parts of this machine.
CAUTION: The machine is heavy. Get assistance before attempting to transport or move it.
CAUTION: To prevent serious damage to the floor surface, when using burnisher, make sure the machine
is always moving forward or backward when the pad driver is in contact with the floor.
CAUTION: To prevent overloading motor, do not use burnisher for wet scrubbing. There is no skirt on
burnisher to contain water. Water could splatter.
Model 01193B
Voltage (V) 120
Frequency(Hz) 60
Current(A) 12.5
Operators Handle plastic
PadDriver 20"
BurnishingSwath 20"
Pad Speed (rpm) 1700
Motor Horsepower 1.5
Power Cable Length (ft) 50
Weight(lbs.) 82

CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700 Page -11 -
Section II
Parts and Service Manual
(70127B)
UltraSpeed®
Burnisher
1700

CLARKETECHNOLOGYUltraSpeedBurnisher1700
AssemblyParts List 11/00
Page - 14 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700
35
36
37 38
39
41
40 42
43
38 37 44 45
123
4567
9
10
11
12
13
14
15
16
17 18
19
19
20
21
22
23
24
12
18
25
12
26
31
27
28
29
30
20
2
33
34
32
47
48
49
46
50
51
52
5354
35
40
55
8
56

CLARKE TECHNOLOGY Ultra Speed Burnisher 1700
Assembly Parts List 11/00
Ref# PartNo. Description Qty
28 50836A Retainer 1
29 962968 Screw 4
30 63930A BeltGuard 1
31 57370A Base,Retainer (incl.w#25) (1)
32 980681 Washer,Wave 2
33 39857A Wheel 2
34 920346 Palnut 2
35 85383A Screw, 10-32 x 3/47
36 50779A Handle,Front 1
37 50820A Spring, Extension 2
38 50798A Lever,Switch 2
39 50780A Handle,Rear 1
40 920722 Nut, 10-32 ESNA 7
41 962957 Screw 2
42 50821A Spring,Compression 1
43 50799A Interlock, Main 1
44 50806A Button, Interlock 1
45 40109A Switch 2
46 41956A Cord 1
47 747553 StrainRelief 1
48 66542A Pin 1
49 69124B HandleTube 1
50 64325A CordHook 1
51 930005 Rivet 2
52 10083A Cord,PowerSupply 1
53 85381A Screw 1
54 35703A Bumper 1
55 170686 Locknut 1
56 77378A Label,ClarkeTechnology 2
Ref# PartNo. Description Qty
1 50774A Knob 2
2 170860 Washer,Flat 12
3 62423A Clamp 1
4 49310A Wire 1
5 32369A Cover(gray) 1
32369B Cover(black) 1
6 44201A Light(rectangular) 1
34259A* Light(round) 1
7 85517A Screw 2
8 77371A Label,ALTO 1
9 41403A CircuitBreaker 1
10 699202 CableTie 1
11 45025A Motor(includesone#12) 1
12 915044 Key(oneincludedw/#11) (3)
13 57262A Pulley 1
14 60193A Axle 1
15 20006A Frame 1
16 30035A Bumper 1
17 170820 Screw 4
18 57714A RetainingRing 2
19 51185A Bearing 2
20 980638 Lockwasher 8
21 85703A Screw 4
22 69047A Spindle 1
23 50921A Belt 1
24 57261A Pulley 1
25 56925A PadDriver(Includes27,31) 1
26 962714 Screw 1
27 57369A RetainerPad(incl.w/25) (1)
CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700 Page -15 -
*(NOTE:PartNumber34259Arequiresretainer80201A)

CLARKE TECHNOLOGY Ultra Speed Burnisher 1700
Electrical Schematic 120Volts 11/00
Page - 16 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700

CLARKE TECHNOLOGY Ultra Speed Burnisher 1700
Motor (45025A) Drawing and Parts List 11/00
Ref PartNo. Description Qty
1 50717A Thru-Bolt 2
2 52045A Commutator Bracket 1
3 56282A Hex Nut 1
4 912287 Rectifier 1
5 962054 Screw 1
6 448396 Spring (w/8) 4
7 51405A Brush Assembly (w/8) 4
8 51435A Brush Board Asm. (1)
(incl. 6,7,19,20 &21)
9 962730 Screw - Brush Board 4
11 58057A Stator Frame 1
12 902547 Bearing - Upper 1
13 50136A Armature 120V 1
14 915044 Key 1
15 902550 Bearing - Lower 1
16 53528A Bottom End Plate 1
17 980076 Wave Washer 1
18 55646A Cord Assembly 1
19 59606A Varistor (120V) (w/8) 1
20 55647A Yellow Lead (w/8) 1
21 55648A Red Lead(w/8) 1
22 831102 Strain Relief 1
23 58056A Strain Relief 1
11
2
3
22
45
23 18
20
21
666
7
7
9
7
7
989
17
11
6
12
13
15
16
CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700 Page -17 -
19
14