American Standard Towel Bar 6718 User manual

Certified to comply with ANSI A112.18.1
U.S. Patent No. D403,750
18" TOWEL BAR
24" TOWEL BAR
M968217B
6718
6724
118" and 24" TOWEL BAR
48 TO 72
INCHES FROM
FLOOR
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Installation
Instructions
Install the WALL ESCUTCHEON (7) on the MOUNTING PLATE (5). Place the 18" TOWEL BAR (1) and 24' TOWEL BAR (2) into the
SIDE SUPPORT BRACKET (10, 10a). Align slot in towel bar with notch in recess of support post (10, 10a) (see Figure A). Place the18"
TOWEL BAR (1) and 24' TOWEL BAR (2) on the ESCUTCHEON (7) and MOUNTING BRACKET (5). Secure with MOUNTING SCREW (8).
Tighten fully.
Push INDEX BUTTONS (9) into SIDE SUPPORT BRACKET (10, 10a). See illustration.
The 18" TOWEL BAR (1) and 24' TOWEL BAR (2) work best if secured to a wall stud or cross brace within the wall,
using the SCREWS (3) supplied.
If the 18" TOWEL BAR (1) and 24' TOWEL BAR (2) is to be installed on a tile or plaster wall the TILE ANCHORS (4) or
DRYWALL ANCHORS (6) and SCREWS (3) should be used.
For installations on drywall, use DRYWALL ANCHORS (6) and SCREWS (3) for securing MOUNTING PLATE (5) to wall. Place #2 Phillips
screwdriver or cordless screwdriver into recess of anchor. Press into drywall while turning the anchor clockwise until it is seated flush with
the wall. Place MOUNTING PLATE (5) over DRYWALL ANCHORS (6) and insert SCREWS (3) with #2 Phillips screwdriver. See illustration
below. Secure MOUNTING PLATE (5) to wall with SCREWS (3).
USE MOUNTING PLATE
AS TEMPLATE
5
5
6
4
64
4
3
37
8
9
10 10a
CENTER
LINE
FINISHED
WALL
48" TO 60"
(OPTIONAL)
CENTER LINE
21
Regular Screwdriver
Recommended Tools
Phillips Screwdriver
Drill
10'
Tape Measure
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR
WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID,
POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH
WITH A COARSE SURFACE.
STANDARD
COLLECTION
Determine desired height and location (optional) and mark a center line. For the 24" TOWEL BAR (2) mark a centerline 24" horizontally
from the first location. For the 18" TOWEL BAR (1) mark a centerline 18" from the first location. Using the MOUNTING PLATE (5) as a
template mark the two mounting holes. Repeat for the other MOUNTING PLATE (5). If MOUNTING PLATE (5) is secured to a stud or
cross brace, drill small pilot holes for SCREWS (4).
For installations on tiled walls, If TILE ANCHORS (4) and SCREWS (3) are used for securing MOUNTING PLATE (5), then drill two
1/4" diameter holes a minimum of 1-1/4" deep. Insert the two TILE ANCHORS (4) flush with face of the finished wall. Secure
MOUNTING PLATE (5) to wall with SCREWS (3).
24"
18"
SLOT IN TOWEL BAR
NOTCH IN RECESS OF SUPPORT POST
Figure A

M968217B
ACCESSORIES
18" TOWEL BAR
24" TOWEL BAR
STANDARD
COLLECTION
MODEL NUMBERS
6718
6724
CHROME
SATIN
002
295
Replace the "YYY" with
appropriate finish code
M962136-0070A
MOUNTING BRACKET
M962140-YYY0A
TOWEL BAR SUPPORT KIT
M907736-YYY0A
ESCUTCHEON
6718
18" TOWEL BAR
6724
24" TOWEL BAR
M919236-YYY0A
18" TOWEL BAR
M962136-0070A
MOUNTING BRACKET
M962140-YYY0A
TOWEL BAR SUPPORT KIT
M907736-YYY0A
ESCUTCHEON
M962233-0070A
INDEX BUTTON
M919237-YYY0A
24" TOWEL BAR
18"
24"
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2002