Ametek SHPF1 SCR Series Operation and maintenance manual

SCR POWER CONTROLLER
Instruction, Operation and
Maintenance Manual
Number: 9100033
Revision 2
530 Lakeview Plaza Blvd, Ste C
Worthington, Ohio, USA 43085
Toll Free: 1-888-PWR-CNTL (797-2685)
Phone: [phone]
Fax: [phone]
Web: www.hdrpower.com
SHPF1 SCR Series
15-120 Amperes
Single-phase
Phase-fired

This manual applies to all Model SHPF1 SCR Power Controls. Former SHPF1/SHPF3 manual – 9100022 has
been replaced with this manual.
For the support representative nearest you, please call Ametek HDR Power Systems main office at (614)-308-
5500.
Revision 1 September 2014 Initial Release
Revision 2 July 2015 Revised Address
2015 by Ametek HDR Power Systems. No portion of this document may be reproduced either mechanically or electronically without the
prior consent of Ametek HDR Power Systems.

SHPF1 SCR Power Controller Table of Contents
Rev 2 Ametek HDR Power Systems i
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS .............................................................................................................1
CHAPTER 1 - DESCRIPTION..............................................................................................................................3
1.1General Description 3
1.2Application 3
1.3Operation 3
1.4Specification 3
CHAPTER 2 - OPTIONS ......................................................................................................................................5
2.1General 5
2.2Option OC (Single-Phase Overcurrent Trip) 5
2.3Option CL/OC (Current Limit/Overcurrent Trip) 5
2.4Option CR/OC (Current Regulation/Overcurrent Trip) 5
2.5Option PR (Power Regulation with Current Limit) 5
2.6Option VIPR (Voltage, Power, Resistance Regulation) 6
2.7Option ER (Extended Ramp) 6
2.8Additional Options 6
CHAPTER 3 - INSTALLATION............................................................................................................................7
3.1Mounting the SHPF1 7
3.2Input/Output Wiring 7
3.3Wiring Overtemperature Contacts 7
3.4Command Signal Input 8
3.5Determining Line Frequency 8
3.6Voltage Changeover 8
3.7Options 9
CHAPTER 4 - OPERATION...............................................................................................................................11
4.1General 11
4.2Front Panel Indicators 11
4.3Command Input Control 11
4.4Remote Manual Control with a Potentiometer 12
4.5Auto/Manual Control with a Controller and Remote Potentiometer 13
4.6On/Off Control 14
4.7Shutdown 15
CHAPTER 5 – OPTIONS SETUP ......................................................................................................................17
5.1Option OC (Overcurrent Trip) 17
5.2Option CL/OC (Current Limit/Over Current Trip) 17
5.3Option CR/OC (Current Regulation/Over Current Trip) 18
5.4Option PR 18
5.5Option VIPR 18
CHAPTER 6 - THEORY......................................................................................................................................21
6.1Functional Description 21
6.2Overview of the SHPF1 21
6.3Digital Firing Control Circuit 21
6.4Pulse-Train Firing 21
6.5Phase-Lock Loop 21
6.6SPAN and ZERO Controls 22
6.7Voltage-Squared Feedback 22
6.8Shut-down 22
6.9Soft-Start Circuit 22

Table of Contents SHPF1 SCR Power Controller
ii Ametek HDR Power Systems Rev 2
CHAPTER 7 – TROUBLESHOOTING...............................................................................................................23
7.1Customer-Service Program 23
7.2Troubleshooting Typical Symptoms 23
7.3Static Precautions when Servicing 23
7.4Environmental Problems 24
7.5Input Power and Load Connections 24
7.6Correcting Troubles in the SHPF1 Itself 25
CHAPTER 8 - SERVICE.....................................................................................................................................27
8.1Communication Procedures 27
8.2Spare Parts Orders – Routine or Emergency 27
8.3Spare Parts List 28
8.4Drawing List 29
CHAPTER 9 – WARRANTY POLICY................................................................................................................31
9.1Warranty 31
9.2In-house Repair Services 31
APPENDIX..........................................................................................................................................................33
Appendix A – System Schematic 33
Appendix B – 15-60 A Outline 34
Appendix C – 70-120 A Outline 35
Appendix D – Declaration of Conformity 36

SHPF1 SCR Power Controller Table of Contents
Rev 2 Ametek HDR Power Systems iii
TABLE OF CONTENTS
Par. Title Page
ILLUSTRATIONS
Figure 3.1 Thermostat Connections................................................................................................................. 8
Figure 3.2 Isolated/Non-Isolated Switches...................................................................................................... 8
Figure 3.3 T1 Transformer Connections.......................................................................................................... 9
Figure 4.1 Control Panel.................................................................................................................................. 11
Figure 4.2 Process Controller Input Connections........................................................................................ 12
Figure 4.3 Remote Control with a Potentiometer ......................................................................................... 13
Figure 4.4 Auto/Man Control with Controller and Remote Potentiometer................................................. 14
Figure 4.5 On/Off Control................................................................................................................................ 14
Figure 4.6 Shutdown Control.......................................................................................................................... 15
Figure 5.1 Current Limit/Trip Board............................................................................................................... 17
Figure 5.2 VIPR Board ..................................................................................................................................... 19
Figure 6.1 AC Switch and SCR On-time......................................................................................................... 21
TABLES
Table 1.1 SHPF1 Model Number Breakdown .................................................................................................. 3
Table 1.2 General Specifications of SHPF1 Models....................................................................................... 4
Table 3.1 Wire Size Information........................................................................................................................ 7
Table 3.2 Transformer Voltage Wiring............................................................................................................. 9
Table 5.1 VIPR Regulation Switch Settings................................................................................................... 19
Table 7.1 Troubleshooting Chart (Symptoms and Solutions)..................................................................... 25
Table 7.2 Torque Specifications..................................................................................................................... 25
Table 8.1 SHPF1 Spare Parts List................................................................................................................... 28
Table 8.2 SHPF1 Drawing List ........................................................................................................................ 29

Table of Contents SHPF1 SCR Power Controller
iv Ametek HDR Power Systems Rev 2

SHPF1 SCR Power Controller Safety Instructions
Rev 2 Ametek HDR Power Systems 1
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
WARNING
Observe all warnings and cautions in this manual. Failure to do so may result in serious injury or death.
Refer all service to properly trained and qualified service personnel. Never work alone.
Lethal voltages exist on exposed heat sinks even if the power controller is turned off. Remove power and lock
out power before attempting any service.
This manual contains important safety instructions that must be followed during the installation and
maintenance of the SCR Power controller. Read this manual thoroughly before attempting to operate this
Power controller.
An appropriate branch circuit fused disconnect or circuit breaker with this Power Controller is required to
ensure the safety of operating personnel.
CAUTION
HAZARDOUS VOLTAGES exist at the Power Controller Load, AT ALL TIMES, when input voltage is
connected. This condition exists even when the Power Controller is set to deliver zero output.
Printed circuit boards contain sensitive components that can be damaged by electrostatic discharge (ESD).
Observe precautions for handling electrostatic sensitive devices. Reference Maintenance and Troubleshooting
(Chapter 7) of this manual for details
In case of fire, use a dry chemical fire extinguisher to put out the fire. Using a liquid fire extinguisher may
cause electric shock.
The SCR Power Controller makes use of components dangerous for the environment (electronic printed circuit
boards, electronic components). The components removed must be taken to specialized collection and
disposal centers.
E151547
100kA SCCR
IEC 947-5-1
Made in U.S.A.

Safety Instructions SHPF1 SCR Power Controller
2 Ametek HDR Power Systems Rev 2

SHPF1 SCR Power Controller Description
Rev 2 Ametek HDR Power Systems 3
CHAPTER 1 - Description
1.1 General Description
The SHPF1 is a Single-phase, phase-fired power controller, and can operate with a wide variety of
input signals and line voltages up to 575 Vac and currents ranging from 60 through 120 amperes. The
SHPF1’s output voltage is proportional to its input signal. The SHPF1 features pulse-train firing which
provides high immunity to possible SCR firing disturbances, and phase-lock loop circuitry which
ensures line frequency synchronization. Other features are input isolation from ground, soft-start, and
automatic restart circuitry. Terminals are provided to permit connection of a variety of external control
methods. A more detailed description of the features mentioned above is provided in Chapter 6 of this
manual.
1.2 Application
Phase-Fired SCR Power Controllers provide infinitely variable firing angles for precise control of
single-phase power to resistive or inductive loads. This precise control is essential for transformer
coupled loads or loads with great resistance changes due to temperature or start-up. Phase-Fired
units may also be used on straight resistive loads as well, but the lower power factor and higher
harmonics may present a problem to other equipment mounted nearby. A zero fired model would be a
better choice.
1.3 Operation
The SHPF1 accomplishes power control by the switching action of a pair of inverse-parallel power
SCRs. The switching, or gating, of the SCRs is controlled by a digital firing control circuit synchronized
“in phase” with line frequency (either 50 or 60 Hz). A soft-start (approximately a 12 cycle ramp)
feature is standard that allows the Power Controller to fire into the primary of a transformer or to
control power to heating elements which have a large resistance change during start-up. The output
may be adjusted by the on-board multi-turn potentiometers or by a voltage or current signal from a
process controller. ZERO and SPAN controls allow the user to calibrate the SCR unit's output to the
process command signal. Terminals are available for connection of a remote manual potentiometer.
1.4 Specification
Specifications for the SHPF1 SCR power controller are given in Tables 1.1 and 1.2.
Table 1.1 SHPF1 Model Number Breakdown
SHPF1 – 480 – 120 – CR – UB – 01
NOTE: N.O. Thermostat is included in current ratings above 60 A.
120 Vac - 120
240 Vac - 240
400 Vac - 400
480 Vac - 480
575 Vac - 575
15 A rms - 15
30 A rms - 30
40 A rms - 40
60 A rms - 60
70 A rms - 60
90 A rms - 90
120 A rms - 120
N.O. Thermostat - NO
N.C. Thermostat - NC
RMS Current Limit/OC - CL
RMS Current Reg/OC - CR
Over Current Trip - OC
True Power Reg/CL - PR
Extended Ramp - ER
Volt/Cur/Pwr/ResReg - VIPR
Can have multiple selections
4-20 mA - 01
0-10 Vdc - 02
0-5 Vdc - 03
Auto/Man - 04
Manual Pot input - 05
Others
-
xx

Description SHPF1 SCR Power Controller
4 Ametek HDR Power Systems Rev 2
Table 1.2 General Specifications of SHPF1 Models
Input line voltage: *120, 240, 400, 480, or 575 Vac,
+10%, -15% , Single-phase
Line frequency: * 50 or 60 Hz
Current rating: *As indicated by model number (refer to Table 1.1)
Thermostat contact rating: 120 Vac, 5 A; resistive
Input Signal:
Non-isolated
Isolated
0 to 1.5 V (min); 0 to 10 V (max)
0 to 6 mA (min); 0 to 20 mA (max)
Control methods: 1. Potentiometer, 5 k, 1/2 watt (Customer-supplied).
2. Dry contact closure (customer-supplied).
3. Temperature or process controller**
Control signal input impedance:
Non-isolated input
Isolated input
1500 
500 Control signal isolation:
From SCRs 2,500 Vac
From ac power input lines 2,500 Vac
From chassis 500 Vac Power output:
Voltage regulation Voltage Squared
Power output linearity versus
control signals input
+2% (Non-isolated)
+5% (Isolated)
Power SCRs protection:
Current surge Subcycle I² T semiconductor fuse.
Transient voltage spikes (dv/dt)
SCCR Rating
Metal Oxide Varistor (MOV) and R-C snubber across each SCR pair; all
SCRs have PIV rating of 1,400 V.
100kA Miscellaneous:
Phase-firing timebase 0º to 180º conduction per SCR
Controls: ZERO and SPAN potentiometers; 10-turn, screwdriver-adjustable.
Approvals UL/cUL (E151547), CE
Ambient Temperature range:
Environment 32 ºF to 122 ºF ( 0 ºC to 50 ºC) surrounding air
Pollution degree 2
Overvoltage Category III
Storage 14 ºF to 158 ºF ( -10 ºC to 70 ºC)
Weight per unit: Current Rating
15 through 60 A
70 through 120 A
lbs
6
18
kg
2.7
8.2
Outline and mounting: See appropriate drawing in Appendix
* Specify with order
** If you will be using temperature/process controller, specify its output; e.g., 4-20 mA, 0-10 Vdc, 2-10 Vdc,
etc. with your order.
NOTE: The SHPF1 should be tested or operated with an adequate load since an open output will have line
voltage at the load connections.