Amica 500 User manual

Freestanding cooker 500 and 600 / Range 2013
Gas - electric
Ceramic - electric
Electric
SERVICE MANUAL

2
Manual developed by:
R. Stołowski
E. Banach
R. Bedoński
Address your questions to:
[email protected]

3
Contents
1. Product identication 4
2. Door assembly 5
3. Oven chamber seal 8
4. Knob assembly (gas cooker) 9
5. Oven shelves 10
6. Hob (gas cooker) 11
7. Thermocouple (gas cooker) 13
8. Front panel assembly 14
9. Programmer 15
10. Control panel buttons 16
11. Igniter connector assembly (gas cooker) 17
12. Temperature regulator assembly and function switch 18
13. Rotisserie motor assembly 19
14. Convection fan assembly 20
15. Bottom heater 21
16. Convection fan heater 22
17. Top heater 23
18. Front wall 24
19. Fittings 25
20. Hob assembly (ceramic hob cooker) 27
21. Energy metering device (ceramic hob cooker) 29
22. Hob assembly (electric cooker) 30
23. Cam connector of the hot plate 31

4
Product identication
Location of nameplate
All the necessary information about the product can be found on the nameplate. The
nameplate of the freestanding cooker is located on the back wall.
The serial number
The appliance serial number is printed on the nameplate. The serial number is nec-
essary to match the correct spare parts for the product.
Decoding the serial number.
An example of the serial number: 99991111136513
9999 - serial number in the batch of the product
11111 - Product Code (a unique number for each type of appliance)
365 - day of production
13 - year of production

5
Door assembly
Removing the door assembly
1. Lift the lock of the left and right door hinge.
2. Position the door at an angle of 45° relative to the front of the appliance, lift and
pull out toward yourself.
3. Place the door on a at surface with the handle facing downward. Using a at
screwdriver, pry the cap of the prole on one side to remove it.

6
4. Pull out the inner glass panel and carefully lift it. Do the same with the middle
glass panel(s).
Door assembly
5. Remove the screw that fastens the hinge to the inner glass prole. Pull the hinge
out of the prole.
6. Use the screwdriver to pry and remove the glass panel bracket.
Refer to the Annex to the SBI_001 service manual.

7
Door assembly
7. Remove the door handle by undoing the screws.
8. To reassemble the components follow the above steps in reverse order.

8
Oven chamber seal
Dismantling the oven chamber seal
1. Unhook the seal holders from the front wall in four places (in the corners).
2. To reassemble the components follow the above steps in reverse order.
The seal should be mounted
with the joint facing down.

9
Knob assembly (gas cooker)
1. Pry the knob's interior part, squeeze both parts together and pull toward your-
self.
2. To reassemble the components follow the above steps in reverse order. Impor-
tant! There is a spring between the two elements.

10
Oven shelves
Dismantling the shelf supports
1. Remove the runners from the shelf supports, unhook the shelf supports from the
mounting holes.
2. To reassemble the components follow the above steps in reverse order.

11
Hob (gas cooker)
1. To dismantle the cover assembly open it maximally (to vertical position) and pull
it upward. Remove the two screws that x the hob to the freestanding cooker
body.
Dismantling the hob
2. Undo the screws that x the burner bodies (two screws for each burner).
3. Gently push the burner body to the inside; pay special attention not to damage
the thermocouple and spark igniter.

12
Hob (gas cooker)
4. Gently slide the hob toward the back and lift it.
5. After dismantling the hob, remove the old seal and, after repair, install a new seal
when mounting the hob.
6. To reassemble the components follow the above steps in reverse order.

13
Thermocouple (gas cooker)
1. Unhook the thermocouple from the valve. Unhook the thermocouple lock located
in the burner body, prying it with a at screwdriver.
Replacing the thermocouple
3. To reassemble the components follow the above steps in reverse order.
2. Slide the thermocouple from the burner body guide.

14
Front panel assembly
1. Dismantle the door assembly. Remove the two screws that x the front panel to
the freestanding cooker body. The screws are located on the bottom of the panel
and are visible after opening or dismounting the door. Gently pull the panel to-
ward yourself.
Dismantling the front panel
2. To reassemble the components follow the above steps in reverse order.

15
Programmer
1. Disconnect the wiring harness, pry and unhook the programmer from the internal
panel by pushing it to the outside.
Dismantling the programmer
2. To reassemble the components follow the above steps in reverse order.

16
Control panel buttons
1. Using a at screwdriver, pry the buttons' catch and push the buttons to the out-
side.
Replacing the control panel buttons
2. To reassemble the components follow the above steps in reverse order.

17
Igniter connector assembly (gas cooker)
1. Dismantle the knobs, dismantle the front panel assembly. Remove the washer
located directly under the knob assembly, on the valve stem. Pry and turn the
igniter assembly and remove it from the valve. Repeat the procedure for all igniter
connectors.
Dismantling the igniter connector
2. To reassemble the components follow the above steps in reverse order.

18
Temperature regulator assembly and function switch
1. Dismantle the hob, dismantle the knob. Disconnect the temperature regulator
wiring harness. Remove the two screws that x the regulator.
Dismantling the temperature regulator
2. To reassemble the components follow the above steps in reverse order.
Dismantling the function switch
1. Dismantle the hob, dismantle the knob. Disconnect the function switch wiring har-
ness. Remove the two screws that x the function switch.
2. To reassemble the components follow the above steps in reverse order.

19
Rotisserie motor assembly
1. Dismantle the rear wall by removing the screws on the sides. Disconnect the wir-
ing harness from the rotisserie motor. Remove the two screws that x the rotis-
serie motor.
Replacing the rotisserie motor
2. To reassemble the components follow the above steps in reverse order.

20
Convection fan assembly
1. Remove the rear wall according to relevant instructions in the manual. Remove
the fan guard by removing the screws. Remove the fan propeller by holding the
fastening nut with the pliers and rotating propeller.
Dismantling the fan
3. To reassemble the components follow the above steps in reverse order.
2. Remove the fan drive by bending the locking tab. Then turn counter-clockwise
and pull the fan drive toward you. Disconnect the fan drive wiring harness.