AMP Lighting PetalPro APl-3033-B-BZ Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP® PetalPro Path & Area Light
APl-3033-B-BZ

AMP®PetalPro Path & Area Light
APL-3033-B-BZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
Important Safety Instructions
!
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the war-
ranty.
These instructions do not intend to cover all variations in installation, opera-
tion maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing
this xture.
2. Warning: this xture is not intended to be installed within 10 feet [3
meters] of a pool, spa or fountain.
3. This xture is intended to be used only with a power supply (transform-
er) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Underground Low Energy Cable must not be buried over 6” (15.2 cm) in
order to connect to the main low voltage cable.
5. Wiring connections must be made with UL Listed wire connectors that
are suitable for the application.
6. Position the wire connector so that it is located within 6 inches (15.2
cm) from a building structure, a luminaire, or tting.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the xture with a damaged or missing lens or shield.

[email protected] • 813.978.3900
Product Dimensions
–3–
Package Contents
Product Dimensions
A. (1) Fixture Body
A. (1) Mounting Accessory
B. (1) GU4 or M11 LED Bulb
26”
5”
4.87”
4.87” 7.5”

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
2
1
AMP®PetalPro Path & Area Light
APL-3033-B-BZ
Remove Lens
Shade
Screw
Lens
Using a screwdriver, loosen
screws on the lens and remove
the lens from the shade.
Install Bulb
Socket
GU4 or
MR11 Bulb
Insert bulb with correct wattage
and type marked on xture label
and push into place.
CAUTION: Do not exceed maxi-
mum wattage marked on xture
label.
3
Install Lens
Shade
Screw
Lens
Place the lens back onto the
shade and secure with previously
removed screws. Tighten until
snug with screwdriver.

[email protected] • 813.978.3900
–5–
INSTALLATION & MAINTENANCE GUIDE
4
5
Install Stake
AMP®PetalPro Path & Area Light
APL-3033-B-BZ
Determine the desired location
for mounting the luminaire.
Hammer the stake into the
ground until ange of stake is
ush to grade. To avoid damage
to the stake, place a board on
top of the stake while hammer-
ing.
Note: If the ground is hard and
the stake is difcult to install,
make a crosscut in the ground
using a at shovel.
Board
Ground
Soil
Stake
Install Fixture Body to Stake
Pass supply wires through
the center hole of the stake
and thread the stem onto
the stake. Hand tighten until
snug. Clear away area in
ground and lay supply wires
into wireway slots.
Ground
Stem
Supply Wires
Soil
Stake

INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
6
Install/Replace Bulb
Wire Connections
AMP®PetalPro Path & Area Light
APL-3033-B-BZ
Strip two leads from xture wires. Using two UL listed wire connectors
(sold separately), connect leads from xture wires to main supply cable
leads.
Main Supply Cable
Fixture Wires
Wire Connectors
7
Adjust Shade Direction
Loosen the knuckle to adjust the
shade to your desired angle. Once
your desired angle is achieved,
hand tighten the lock screw to
secure the shade direction.
Shade
Lock Screw ROTATE
Please reverse Step 1 - Step 3 to expose the bulb and replace it with the
correct wattage and type marked on the xture label.
IMPORTANT: The Bulb must be protected from moisture and dust at all
times. Always reinstall the lens when removed.

–6––6–
[email protected] • 813.978.3900
–7–

IS-APL-3033-B-BZ-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2022, AMP® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com