AMP Lighting AHS-67 Series Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP® LED Hardscape Lights
AHS-67XX Series

[email protected] • 813.978.3900
INSTALLATION & MAINTENANCE GUIDE
AMP®LED Hardscape Lights
AHS-67XX Series
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
luminaire.
2. Warning: risk of electrical shock. Install all luminaires 10 feet (3.05M) or
more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. DO NOT INSTALL in walls where the capstones overhang the wall less than
3/4” [19mm] or under stairs where the tread overhangs the riser less
than 3/4” (19mm).
5. Wiring connections must be made with wire connectors that are suitable
for outdoor use.
6. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminare, or
tting.
7. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
8. If additional lengths of low voltage cable are required, please contact
www.voltlighting.com or call 1-813-978-3700.
Package Contents
A. (1) Luminaire
B. (2) Self-tapping Screw
C. (2) Wall Anchors
Important: Please Read Before Installation
!

www.amplighting.com
–3–
Product Dimensions
4.2”
.75”
7.2”
13”
19”
.75”
.75”
.75”
Install Luminaire in Brick or Masonry Wall
Install Mounting Plate
1
Brick or
Masonry Wall
Mounting Plate
Barrell Nut
Determine the desired location for
each luminaire before construction of
the wall is started.
Insert the stainless steel mounting
plate (sold separately), in between
the layers of hardscape material. If
prefered, use an adhesive or mortar,
to secure the luminaire in place.
* Adhesive or mortar is not
provided by AMP®

[email protected] • 813.978.3900
–4–
INSTALLATION & MAINTENANCE GUIDE
AMP®LED Hardscape Lights
AHS-67XX Series
Install Luminaire
2
Mounting Plate
Glare Guard
Route the luminaire wire through
the wall to the main low voltage
supply cable using standard
masonry procedures. A “V”
shaped notch can be cut into the
hardscape material to aide in
wire management.
Attach the glare guard (sold
separately) and the luminaire
to the stainless steel mounting
plate by using machine screws
(ships with mounting plate).
Luminaire
Mounting Screw
Wire Connection
3
Strip both leads from the luminaire pigtail. Using two wire connectors (sold
separately), connect the leads from the luminaire to the main supply cable
leads.
Luminaire Wires
Main Low Voltage
Supply Cable
Wire Connectors

–5–
www.amplighting.com
–5–
Install Luminaire in Railing, Deck Over-hang or Stair
Determine Luminaire Location
4
Determine the desired location for the luminaire.
Place the luminaire to the mounting surface and mark two points on the
mounting surface where the holes are on the ends of the luminaire. The
marks will be used for self-tapping screws or wall anchors.
Note: Wall anchors are required for certain installation conditions
(brick wall, concrete wall, etc.).
A wireway hole may be drilled through the decking fascia or other surface
adjacent to the mounting surface.
A. Hold the luminaire in the desired mounting location. Mark the
location where the wire exits the luminaire.
B. Drill a hole through surface (suggested 1/4” [6.5mm] hole).
C. Thread the wire through the drilled hole.
Self-tapping
Screw
Luminaire
Railing, Deck
over-hang or Stair
Mark
Install from Bottom Install from Side
Self-tapping
Screw
Luminaire
Mark
Wireway
Hole
Railing, Deck
over-hang or Stair
Wireway Hole

[email protected] • 813.978.3900
–6–
INSTALLATION & MAINTENANCE GUIDE
AMP®LED Hardscape Lights
AHS-67XX Series
Install Luminaire
5
Install the luminaire and glare guard using provided self-tapping screws. If
the screws are difcult to install, mark holes and drill 1/8” pilot holes.
If wall anchors are required, drill proper holes from the marks on the
mounting surface and then insert the wall anchors. Then install the
luminaire and glare guard and secure them with the self-tapping screws.
Rubber washers are required during installation from the side.
NOTE: DO NOT OVER TIGHTEN SCREWS.
Return to Step 3 to complete the wire connections.
Self-tapping
Screw
Luminaire
Railing, Deck
over-hang or Stair
Mark
Install from Bottom Install from Side
Self-tapping
Screw Luminaire
Mark
Wireway
Hole
Railing, Deck
over-hang or Stair
Wireway Hole
Glare Guard Wall Anchor
Rubber
Washer
Glare Guard

–7–
www.amplighting.com
–7–
Adjust LED Direction
6
Using an Allen wrench, loosen the set screws on the ends of the LED,
then rotate the LED to the desired direction. Always tighten the set
screws after adjustments.
Allen Wrench
Set Screw
Set Screw LED

IS-AHS-67XX-ver5.pdf
Specications and product details subject to change without notice.
© Copyright 2018, AMP®Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com