AMP Lighting MR16 HydraPro Operating and safety instructions

AMP®Low Voltage Landscape Lighting
AMP®MR16 HydraPro™ Well Light (Lamp Ready)
AWL-705-25-BBZ
INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com

[email protected] • 813.978.3900
AMP® MR16 HydraPro™ Well Light (Lamp Ready)
AWL-705-25-BBZ
Important: Please Read Before Installation
Important: Safety Instructions
INSTALLATION & MAINTENANCE GUIDE
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing
this luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
7. If additional lengths of low voltage cable are required, please call
1-813-978-3900.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Turn o/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
!
!

www.amplighting.com
–3–
Product Dimensions
Package Contents
Parts Required (sold separately)
A. (1) Fixture
A. (1) MR16 Lamp
8.25”
6.25”
5.5”
Remove Faceplate and Lens
1
Loosen the thumb screws and slide
the housing down to the end of
the brackets. Then untighten the
faceplate screws and remove the
faceplate, gasket, and lens from the
housing.
Screw
Faceplate
Gasket
Lens
Thumb Screw
Housing
B. (1) PVC Tube

[email protected] • 813.978.3900
–4–
AMP® MR16 HydraPro™ Well Light (Lamp Ready)
AWL-705-25-BBZ
INSTALLATION & MAINTENANCE GUIDE
Install Lens and Faceplate
3
Place the lens, gasket, and faceplate
back onto the housing. Secure them
with the screws previously removed.
Hand tighten until snug, then use
a screwdriver to secure the screws
using a star pattern. Adjust housing
to your desired height and angle,then
secure it in place with the thumb
screws.
Screw
Faceplate
Gasket
Lens
Thumb Screw
Housing
3”3”
3”
Dig Hole
4
Dig a hole in the ground making sure
there is approximately 3 inches of
room on all sides surrounding the PVC
tube for pea gravel or sand.
PVC Tube
Hole
Install Bulb
2
Insert the bulb with the correct
wattage and type marked on the xture
label.
CAUTION: Do not exceed the maximum
wattage marked on luminaire label.
NOTE: DO NOT touch bulb with bare
hands. Use soft cloth to handle bulb.
MR16 Bulb
Socket
Soil

–5–
www.amplighting.com
–5–
Soil
Fill Pea Gravel or Sand
6
Install the PVC tube with the xture
in the hole and ll the extra space
with pea gravel or sand for proper
water drainage.
PVC Tube
with Fixture
Pea Gravel
or Sand
Wire Connection
5
Place the xture onto the PVC Tube.
Pass the luminaire pigtail through the
PVC tube.
Strip both leads from the luminaire
pigtail. Using two wire connectors
(sold seperately), connect the leads
from the luminaire to main supply
cable leads.
PVC Tube
Wire Connector
Main Supply Wire
Soil
Pigtail
Fixture

[email protected] • 813.978.3900
–6–

–7–
www.amplighting.com
–7–

is-AWL-705-BBZ-ver4.pdf
Specications and product details subject to change without notice.
© Copyright 2018, AMP®Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com