AMP Lighting KinglyPro APL-3020-B-BZ Operating and safety instructions

- 1 -
AMP®Low Voltage Landscape Lighting
AMP® KinglyPro Path Light (Lamp - Ready)
APL-3020-B-BZ
INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com

Package Contents
Product Dimensions
A. (1) Fixture Body
B. (1) Fixture Hood
9”
3”
25.5”
C. (1) Inner Shade
D. (1) Stake
Parts Required
A. (1) LED Bulb
- 2 - - 3 -
Important Safety Instructions
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or
more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm)
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage
lamp.
6. Do not operate the luminaire tting with a missing or damage shield.
SAVE THESE INSTRUCTIONS
!
AMP®KinglyPro Path Light (Lamp Ready)
APL-3020-B-BZ
INSTALLATION & MAINTENANCE GUIDE
Important Safety Instructions: Read Before Installation
!
www.amplighting.com [email protected] • 813.978.3900

Install Fixture Body to Stake
5
Fixture Body
Stake
Pigtail
Wireway Slot
Remove Fixture Hood and Inner Shield
2
Remove the nial and the hat from the
inner shield. Pull the inner shade off of
the xture body to expose the socket.
Finial
Fixture
Body
Inner Shield
Install Lamp
3
Insert the bulb with the correct
wattage and type marked on the
xture label.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
NOTE: DO NOT touch bulb with bare
hands. Use a soft cloth to handle bulb.
Socket
Bulb
Install Stake
1
Board
Stake
Soil
Ground
- 4 - - 5 -
Install Hat and Inner Shield
4
Push the inner shield onto the xture
body. Place the xture hat back onto
the inner shield and secure with
the nial previously removed. Hand
tighten.
Hat
Fixture
Body
Inner Shade
Determine the desired location for mounting
the xture. Hammer the stake into ground
until ange of stake is ush to grade. To avoid
damage to the stake, place a board on top of
the stake while hammering.
NOTE: If the ground is hard and the stake is
difcult to install, make a crosscut in ground
using a at shovel.
Clear away area in the ground at the
wireway slot on top of the stake. Lay
the luminaire pigtail into the wireway
slot and thread the stem into the
stake. Tighten to secure the base.
Hat
Finial
AMP®KinglyPro Path Light (Lamp Ready)
APL-3020-B-BZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com [email protected] • 813.978.3900

Install/Replace Bulb
Please refer to Step 2 - Step 4 to expose the Lamp and replace it with the
correct wattage and type marked on the xture label.
IMPORTANT: LED Lamp must be protected from moisture and dust at all
times. Always reinstall lens when removed.
- 6 -
Wire Connection
6
Pigtail
Main Supply Cable
Wire Connectors
Strip both leads from the luminaire pigtail. Using two wire connectors
(sold separately), connect the leads from the luminaire to the main low
voltage supply cable leads.
AMP®KinglyPro Path Light (Lamp Ready)
APL-3020-B-BZ
INSTALLATION & MAINTENANCE GUIDE

- 8 -
Specications and product details subject to change without notice.
© Copyright 2019, AMP®Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com