AMP Lighting AFL-40 LI-B-BZ Series Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Line Voltage Landscape Lighting
AMP®120V Brass Flood Light with Knuckle (Constant Output)
AFL-40XX-LI-B-BZ

AMP®120V Brass Flood Light with Knuckle (Constant Output)
AFL-40XX-LI-B-BZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important: Please Read Before Installation
!
Important Safety Instructions
!
1. This LED oodlight uses the latest in solid state lighting technology for
long life, low maintenance, and high efceiency.
2. An internal power-factor-corrected switch mode supply allows this x-
ture to be used from any nominal 90V-277VAC, 60Hz supply without any
variation in light output.
3. Suitable for use in:
A. Ambient Temperatures of: -20~+45°C (-4~+113°F)
A. Wet Locations
Note: Save these instructions for future reference.
To avoid the risk of re, explosion, or electric shock, this product should be
installed, inspected, and maintained by a qualied electrician only, in accor-
dance with all applicable electrical codes.
To avoid electric shock:
1. Be certain electrical power is OFF before and during installation and
maintenance.
2. Luminaire must be connected to a wiring system with an equip-
ment-grounding conductor.
To avoid explosion:
1. Make sure the supply voltage is the same as the rated luminaire voltage.
2. Do not install where the marked operating temperatures exceed the
ignition temperature of the hazardous atmosphere.
3. Do not operate in ambient temperatures above those indicated on the
luminaire.
For supply connections use wire rated for at least 90°C (194°F)
Warning: These luminaires should ONLY be installed by a qualied electri-
cian.

[email protected] • 813.978.3900
Parts Required
–3–
Package Contents
A. (1) Fixture body
A. (1) Mounting Accessory (Sold Separately)
Products Model #
Model Input Voltage Hertz Input Cur-
rent Watt
9W Flood Light 90-277 60 0.2 9
17W Flood Light 90-277 60 0.4 17

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
AMP®120V Brass Flood Light with Knuckle (Constant Output)
AFL-40XX-LI-B-BZ
Two installation methods are provided for this xture:
Surface Mount- Page 5
Stake Mount- Page 6
Product Dimensions
2.92”
4.47”
1.98”
3.43”
1.1”
1.15”
4.5”
5.96”
3.55”
4.91”
2.29”
2.41”
120VAC 9W
120VAC 17W

[email protected] • 813.978.3900
Install Surface Mount to Fixture body
1
Install Fixture Body to Surface
2
Option 1: Surface Mount
Surface Mount
Wire Exit Supply Cable
Fixture Body
Glare Guard Pass the supply cable through
the center hole of the surface
mount. Then thread the surface
mount onto the xture body.
Make sure the wire exit on the
surface mount and the glare
guard are facing the opposite
direction after installation.
Wire Exit
Self-tapping Screw
Supply Cable
Mark
Place the supply cable in the wire exit. Then attach the surface mount
with the xture body to the mounting surface and secure with self-tap-
ping screws using a screwdriver to tighten.
NOTE: Wall anchors are required for brick walls or concrete walls. To
determine anchor locations, place the surface mount onto your de-
sired location and mark points using the hole on the surface mount as a
guide.
Go to the Step 3 - Step 4 for wiring connections and direction adjust-
ment.
Fixture Body
Mounting Surface
Surface Mount
Wall Anchor (optional)

INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
Install Stake
1
Option 2: Stake Mount
AMP®120V Brass Flood Light with Knuckle (Constant Output)
AFL-40XX-LI-B-BZ
Determine the desired location
for mounting the stake. Hammer
the stake into the ground until
ange of stake is ush to grade.
To avoid damage to the stake,
place a board on top of the stake
while hammering.
Note: If the ground is hard and
the stake is difcult to install,
make a crosscut in the ground
using a at shovel.
Board
Ground
Stake
Install Fixture Body to Stake
2
Pass the supply wires through
the center hole of the stake
and thread the xture body
onto the stake. Hand tight-
en until snug. Clear away an
area in the ground and lay the
supply wires into the stake’s
wire exit.
Go to the Step 3 - Step 4 for
wiring connections and direc-
tion adjustment.
Ground
Supply Wires
Soil
Stake
Fixture Body

–6––6–
[email protected] • 813.978.3900
–7–
Wire Connections
3
Hub Body
By using the Allen wrench, loosen screws and remove the cover from
the hub body.
Insert the main supply cable, xture supply cable, other xture supply
cable or next hub supply cable into the hub body from the different
conduit. Strip both ends of all cables. Lift the clamps up and insert the
ends of neutral wires into the “NEUTRAL” block. Insert the ends of live
wires into the “HOT” block. Insert the ends of ground wires into the
“GROUND” block. ensure that each wire is pushed into place securely
and close the clamps.
Place the cover back onto the hub body and secure with previously
removed screws. Hand tighten until snug with Allen wrench.
“NEUTRAL” Block
“GROUND” Block
Supply Cable
from Fixture
“HOT” Block
Supply Cable from
other Fixture or
next hub
Screw
Allen Wrench
Cover
Conduit
Adjust Fixture Body Direction
4
Using the Allen wrench, loosen
the screw on the knuckle and
adjust the xture body to your
desired direction. Once your
desired direction is achieved,
tighten the knuckle down with
the Allen wrench.
ROTATE
Screw
Allen Wrench
Fixture body

IS-AFL-40XX-LI-B-BZ-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2021, AMP® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com