AMP Lighting BulletPro MR8 Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP® BulletPro MR8 Spotlight
AAL-1033

AMP®BulletPro MR8 Spotlight
AAL-1033
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
Important Safety Instructions
!
This luminaire is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and in-
structions may result in serious injury, property damage and void the warran-
t y.
These instructions do not intend to cover all variations in installation, opera-
tion maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
xture.
2. Warning: this xture is not intended to be installed within 10 feet [3
meters] of a pool, spa or fountain.
3. This xture is intended to be used only with a power supply (transform-
er) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Underground Low Energy Cable must not be buried over 6” (15.2 cm) in
order to connect to the main low voltage cable.
5. Wiring connections must be made with UL Listed wire connectors that
are suitable for the application.
6. Position the wire connector so that it is located within 6 inches (15.2 cm)
from a building structure, a luminaire, or tting.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the xture with a damaged or missing lens or shield.

[email protected] • 813.978.3900
Product Dimensions
–3–
1
Package Contents
A. (1) Fixture Body
Parts Required (sold separately)
A. (1) MR8 Lamp
0.7”
1.4”
2.45”
3.4”
Install Stake
Board
Ground
Soil
Stake
Determine the desired location
for mounting the stake. Hammer
the stake into the ground until
ange of stake is ush to grade.
To avoid damage to the stake,
place a board on top of the stake
while hammering.
Note: If the ground is hard and
the stake is difcult to install,
make a crosscut in the ground
using a at shovel.

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
3
2
AMP®BulletPro MR8 Spotlight
AAL-1033
Install Glare Guard and Shield to Fixture
Install Fixture Body to Stake
Fixture Body
Fixture Wire
Ground
Soil
Stake
Pass the xture wire through
the center hole of the stake.
Thread the xture body onto
the stake and hand tighten until
snug.
Strip both leads from the xture body. Using two wire connectors (sold
separately), connect the leads from xture body to the main supply
cable leads.
Pigtail
Main Supply Cable
Supply Wire from
Fixture Body
Wire Connectors

[email protected] • 813.978.3900
–5–
INSTALLATION & MAINTENANCE GUIDE
4
5
AMP®BulletPro MR8 Spotlight
AAL-1033
Remove Glare Guard
Rotate the glare guard counter-
clockwise to remove it from the
xture body.
Fixture Body
Glare Guard
Rotate
Install MR8 Bulb
Insert the MR8 bulb with the
correct wattage and type
marked on the xture label and
push into place.
CAUTION: Do not exceed
maximum wattage marked on
luminaire label.
Socket
MR8 Bulb
6
Install Glare Guard
Push the glare guard back onto
the xture body and rotate it
until it is secured.
Fixture Body
Glare Guard
Rotate

INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
7
AMP®BulletPro MR8 Spotlight
AAL-1033
Adjust Direction
Loosen the knuckle at the joint to
adjust the luminaire to your de-
sired direction. Always tighten the
knuckle once your desired direc-
tion is achieved.
Luminaire Rotate
Knuckle
Install/Replace MR8 Bulb
Please reverse Step 5 - Step 6 to expose the MR8 bulb and replace it with
correct wattage and type marked on xture label. Then reinstall the glare
guard.
IMPORTANT: MR8 bulb must be protected from moisture and dust at all
times. Always reinstall glare guard when removed.

–6––6–
[email protected] • 813.978.3900
–7–

IS-AAL-1033-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2020, AMP® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com