AMP Lighting BDL-ASI-9009-25-BK Operating and safety instructions

- 1 -
INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP®120V E12 Bistro Lights
BDL-ASI-9009-25-BK and BDL-ASI-9010-50-BK

- 2 -
www.amplighting.com
AMP®120V E12 Bistro Lights
BDL-ASI-9009-25-BK and BDL-ASI-9010-50-BK
INSTALLATION & MAINTENANCE GUIDE
This xture is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these
codes and instructions may result in serious injury, property damage
and void the warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or
replacing fuses and/or lamps.
2. This light string is rated 125W (1.04A), do not overload.
Connect other lighting strings or decorative outts end to end
up to a maximum of 432W (3.6A) total.
3. Use only two wire outdoor extension cords that have two-prong
grounding plugs and grounding receptacles that accept the two
prong plugs. Do not altwer the plug.
4. Light sockets must be installed base up so that bulbs are facing
downward ONLY.
5. Keep combustible material clear of bulbs. Do NOT allow lamps
or sockets to come into contact with walls, fabrics associated
with shades, blinds or other materials. Lamps should hang freely
in a downward direction with a minimum of 3” space from the
nearest object.
6. Do not cluster the bulbs.
7. Not intended for installation in ceilings, sots, cabinets or other
enclosed spaces.
8. Avoid making connections or disconnections when the equipment
is wet. Do not use with extension cord near or where water may
accumulate. Do not submerse. Keep lamps at least 16 feet from
pools and spas. Keep receptacles dry.
9. For temporary (90 days max) installation and use only.
Important: Please Read Before Installation
!

- 3 -
[email protected] • 813.978.3900
AMP®120V E12 Bistro Lights
BDL-ASI-9009-25-BK and BDL-ASI-9010-50-BK
INSTALLATION & MAINTENANCE GUIDE
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Disconnect power at source prior to re-lamping String
Lights.
2. For outdoor String Lights, do NOT re-lamp light strings
during rain or when wet.
3. Re-lamp String Lights only during dry and calm weather
conditions.
4. Do NOT secure light strings to buildings or other structural
supports using nails, staples or other sharp, conducting
materials. DO NOT DAMAGE THE WIRE.
5. Do NOT pierce or otherwise compromise wires or socket’s
outer covering, jacket or sheathing.
6. Perodically inspect wire and sockets for degradation due
to weather, UV light or other damage. Promptly replace
worn out light string.
Package Contents
A. (1) String (25 feet or 50 feet)
B. (1) Set of Lamps (25 or 50 pieces)
Product Dimensions
24” 11.5”
1.25”
7”
Important: Safety Instructions
!

- 4 -
www.amplighting.com
AMP®120V E12 Bistro Lights
BDL-ASI-9009-25-BK and BDL-ASI-9010-50-BK
INSTALLATION & MAINTENANCE GUIDE
1
Installation Method 1: Using a Guide Wire
3”
String Lights
String Lights
Hanger
Guide Wire
(Sold Separately)
Attach Guide Wire to
Structural Support
Attach Guide Wire to
Structural Support
Pass the guide wire through the holes on the top end of
the sockets and then x the guide wire to your desired
location or tie the bistro string to applicable locations
directly.
2
Installation Method 2: Attach to a Structure
Determine your desired hanging
location. Tighten the screw hook
into the structural support. Make
sure to attach a screw hook to a
structural support at minimum
every 24 feet. Attach the hangers
of the string lights on to the
screw hooks.
String Lights
String Lights
Screw Hook
Screw Hook
Screw Hook
Structural Support
Structural Support
Hanger
Attach to Structurawl Support
MINIMUM EVERY 24 FEET

- 5 -
[email protected] • 813.978.3900
AMP®120V E12 Bistro Lights
BDL-ASI-9009-25-BK and BDL-ASI-9010-50-BK
INSTALLATION & MAINTENANCE GUIDE
3
Multiple Strings Connection (Optional)
It is easy to connect multiple
strings. Refer to wattage
information below.
Socket
Plug
The MAXIMUM wattage per bulb is 5 watts.
DO NOT EXCEED 432 watts with all sets combined.
4
Install Lamps
Tighten the UL Classied bulbs (5
watt Max Candelabra-base) into the
socket clockwise until the top of
the socket forms a tight seal around
the bulb and the bulb makes solid
contact with the socket.
Insert the plug of the rst string into the wall outlet
to complete the installation.
Socket
Bulb

- 6 -
www.amplighting.com

- 7 -
[email protected] • 813.978.3900

- 8 -
Specications and product details subject to change without notice.
© Copyright 2022, AMP® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)