AMP Lighting G2 AAC-HUB2-LI-SS Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Line Voltage Landscape Lighting
AMP® G2 Line-Voltage Junction Hub (120V)
AAC-HUB2-LI-SS

AMP®G2 Line-Voltage Junction Hub (120V)
AAC-HUB2-LI-SS
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
Package Contents
This connection hub is intended for installation in accordance with local
codes and the National Electric Code (NEC). Failure to adhere to these codes
and instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing
this xture.
2. This connection hub can be used for line voltage (100V-277V AC/DC).
3. Make sure the supply voltage is the same as the rated luminaire
voltage.
4. Do not install where the marked operating temperatures exceed the
ignition temperature of the hazardous atmosphere.
5. Do not operate in ambient temperatures above those indicated on the
luminaire.
For supply connections use wire rated for at least 90°C (194°F)
A. (1) Line Voltage Hub
B. (4) Waterproof Seals
C. (1) Wrench
D. (1) Allen Key
A. (4) Trident Stakes B. (1) Coupler
Parts Sold Separately
Product Dimensions
5.5”
4.25”
2.33”
1.67”
5.2” 3.88”

[email protected] • 813.978.3900
–3–
1
Dig A Hole for Line Voltage Hub
Dig a hole in the ground at the desired location. Make sure there is
approximately 3 inches surrounding the line voltage hub for pea gravel
or sand on all sides.
Line Voltage Hub
3” 3”
3”
Soil
Ground
2
By using the provided Allen wrench,
loosen the screws to remove the
cover from the hub body.
If you want to install a path
light or spot light on the top of
the hub, refer to Steps 3-6 for
instructions.
Otherwise, go to Step 7 to
continue the installation.
Screw
Allen Wrench
Cover
Hub Body
Remove Cover
3
Using the wrench, loosen
the lock nut to remove the
waterproof seal and the
waterproof washer from the
cover.
Waterproof Seal
Waterproof Washer
Cover
Lock Nut
Wrench
Remove Waterproof Seal on the Cover

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
5
AMP®G2 Line-Voltage Junction Hub (120V)
AAC-HUB2-LI-SS
4
Remove Lock Nut from Coupler
Remove the lock from the
coupler.
Waterproof Washer
Lock Nut
Coupler
(Sold Separately)
Install Coupler to Cover
Place the coupler with the
waterproof washer through the
top of the hub. Then secure with
the previously removed lock nut.
Waterproof Washer
Lock Nut
Cover
Coupler
(Sold Separately)
6
Install Light Fixture onto Cover
Insert the xture wire through
the coupler and cover. Thread
the light xture onto the
coupler.
Light Fixture
Cover
Coupler
(Sold Separately)

[email protected] • 813.978.3900
–5–
INSTALLATION & MAINTENANCE GUIDE
7
AMP®G2 Line-Voltage Junction Hub (120V)
AAC-HUB2-LI-SS
Install Conduit
1. Loosen the lock nuts to remove the waterproof wire seals from
the hub body.
2. Remove the lock nuts on your conduit.
3. Place the conduit into the holes on the hub body and secure in
place with the previously removed lock nut.
See next step for wire connections.
Hub Body
Allen Wrench
Lock Nut
Wrench
Lock Nut
Waterproof Seal
Waterproof Washer
Conduit
1
2
Conduit
Lock Nut
Hub Body
Wrench
Waterproof Washer
3

INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
8
Wire Connections
AMP®G2 Line-Voltage Junction Hub (120V)
AAC-HUB2-LI-SS
Main Supply Cable
Hub Body
“NEUTRAL” Block
“GROUND” Block
“HOT” Block
Conduit
Supply Cable from
other Fixture or
next hub
Supply Cable
from Fixture
Open the clamp on the connector that you are going to insert the wire in,
insert one side of the supply wire into the connector and close the clamp.
Use the same method to connect the remaining supply wires. One side of
each wire will go into each connector. If you are not continuing your run,
and only have one xture at the end, you will only utilize two terminals
in each block rather than all three.
Insert the ends of the neutral wires into the “NEUTRAL” block. Insert the
ends of the live wires into the “HOT” block. Insert the ends of the ground
wires into the “GROUND” block.
Review step 2 if you have not utilized all the openings on the hub.

–6––6–
[email protected] • 813.978.3900
–7–
9
INSTALLATION & MAINTENANCE GUIDE
AMP®G2 Line-Voltage Junction Hub (120V)
AAC-HUB2-LI-SS
Attach Cover
Place the cover back onto
the hub ensuring the gasket
is in place. Secure with the
previously removed screws.
Hand tighten until snug with
the provided Allen wrench.
If you install a light xture
onto the cover, we recommend
installing the trident stakes
onto the bottom of the hub
body.
Screw
Allen Wrench
Cover
Hub Body
Trident Stakes
(Optional, Sold
Separately)
10
Fill with Pea Gravel or Sand
Install the connect hub with the xture in the hole and backll the
hole with pea gravel or sand.
Soil
Line Voltage Hub
Conduit
Ground
Pea Gravel
or Sand

IS-AAC-HUB2-LI-SS-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2023, AMP®Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com