AMX HPX-U100-BTN User manual

Installation Guide
HPX-U100-BTN Hydraport Single Button Module
Overview
The HPX-U100-BTN Hydraport Single Button Module (FG554-01) is designed to be
used in conjunction with the HPX-1600 Hydraport Base Assembly. See specifications
for module requirements. For more information on the HPX-1600, refer to
www.amx.com.
The HPX-U100-BTN provides a configurable momentary button and LED backlight on
the face of the Hydraport system.
Product Specifications
Installation
Attention! Only a professional, AMX-qualified installer should
perform this installation. Installation must conform to all local codes.
This product may not be installed by the end-user.
Tools Required
• Wire cutting pliers
• Wire strippers
• Small flat blade screw driver
• Phillips Screw Driver (to access Hydraport Base Assembly)
CAUTION! Ensure that the AC Power cord is disconnected from IEC
C-14 power inlet connector on the Hydraport Base Assembly prior to
disassembly of the Hydraport Base assembly or installation of the
HPX-U100-BTN Module (see FIG. 2).
Step 1 - Backside Termination
Before installing the module into the Hydraport Base Assembly, the backside
terminations of the module must be completed. This backside termination requires
connecting 4 insulated wires, or equivalent, to the 4 position phoenix terminal block
located on the back of the module.
Note that for terminations for which the far end of the cable is not accessible either
because the cable has been run under carpet, in a conduit or structure, or is otherwise
fixed, the cable must be placed through the retaining ring (note the orientation of the
retaining ring) then through the mounting surface from bottom to top, then to the
module - before the module is placed into the base assembly (FIG. 3).
Step 2 - Provide a Service Loop
Ensure there is sufficient cable length to provide a service loop for the cable after the
module is installed into the Hydraport Base Assembly (FIG. 4).
Note that the Hydraport Base Assembly travels up and down approximately 228.6 mm
(9”) during operation.
The service loop must accommodate this motion and provide for securing the cable to
the Hydraport Base Assembly for strain relief.
For more detailed information, please refer to the HPX-1600-XX Hydraport Base
Assembly Instruction Manual.
FIG. 1 HPX-U100-BTN Single Button Module
HPX-U100-BTN Specifications
Dimensions (HWD) 25mm x 52mm x 25mm (0.98” x 2.05” x 0.98”)
Weight: 0.1 Kg (3.53oz)
Enclosure: Matt black finished face plate (Polycarbonate plastic).
Front Connections: RCA style connections for:
• Composite Video
• Left Audio
• Right Audio
Rear Connections: 4 Position Phoenix terminal block with connections for:
• S1 Switch Connection 1
• S2 Switch Connection 2
• LED Anode
• LED Cathode
Compatibility: • HPX-1600 Hydraport Base Assembly
Included Accessories: Installation Guide
FIG. 2 HPX-1600 - Power Inlet Cord Removed
AC Power Cord
Power Inlet Connector
on HPX-1600
FIG. 3 Fixed Cable Passing Through Ring, Table and Into the HPX-1600 Chassis
FIG. 4 Secured Service Loop
Module
Fixed cables pass-through
Retaining Ring, Surface
to Module
Fixed cables pass-through
Retaining Ring, Surface
to Module
Retaining Ring
Mounting Surface
HPX-1600 Chassis

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
3/10
©2010 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax [phone] • technical support 800.932.6993 • www.amx.com
93-0554-01 REV: B
Step 3 - Prepare and Connect Wiring
1. Remove approximately 4mm (.18 in) of the wire insulation.
2. Insert each conductor into the corresponding terminal.
3. Secure each connection using the terminal screw, according to the schematic
provided in FIG. 5:
Step 4 - Secure the Cable To the Module
Using small provided tie wrap, secure the cable to the circuit card on the backside of
the module, such that the cable exits to the side of the module (FIG. 6).
Step 5 - Insert the Module Into the HPX-1600 Chassis
Insert the module into the main chassis of the HPX-1600 Base Assembly.
Note the position of module interlock tab: this tab should face towards the bottom of
the HPX-1600 Base assembly when installed in its mounted position (FIG. 7).
Step 6 - Install the Bottom Cover On the HPX-1600
Note: Install any remaining modules into the Hydraport Base Assembly before
installing the Bottom Cover on the HPX-1600.
1. Install the bottom cover (including the Power Inlet Assembly) onto the bottom of
the main frame of the Hydraport Base Assembly.
The cables from the HPX-AU100-CV+A Composite AV Module as well as all
other modules (except AC Power Outlets) will exit the bottom of the Hydraport
Base Assembly through one of four square passages on either side of the
bottom cover.
2. After the bottom cover is secured using four screws, secure the cables to the
corresponding tab near each opening using a small cable tie (FIG. 8).
FIG. 5 HPX-U100-BTN Single Button Module - Wiring Schematic
FIG. 6 Cables Secured To the Module
FIG. 7 Inserting the Module into the HPX-1600 Chassis
Anode
Cathode
S1
S2
R = 1.2KΩ
Tie Wrap
Cables exiting to the side of the Module
Single Button Module
(rear view)
FIG. 8 Bottom Cover - Installed With Cables Exiting and Secured
HPX-1600 Chassis
Aluminum Frame (bottom)
Wire Tie
Wire Tie
Bottom Cover
(secured with 4
mounting screws)
Cable
Cable