Anden A320V1 User manual

FEATURES
Control Onboard digital with diagnostics
Air supply orientation Horizontal
Filter 20"x22"x2" MERV 11
Refrigerant R410A
Coil type Copper tube, Aluminum n
with ElectroFin®E-coat
Drain connection*¾" FNPT
P-Trap required Yes (Included)
Leveling feet Sold separately (Model #5789)
Hanging brackets Included
Duct Kit Sold Separately (Part #5807)
Warranty 5 Years on all parts including
refrigeration system
* Requires drain trap
SPECIFICATIONS
Capacity(1) PPD AT 80°/60%RH 320
Energy factor(1) 2.9 L/kWh
6.0 pints/kWh
Voltage, Phase, Frequency 208–240VAC, 1 Phase, 60 Hz
Current draw (amps)(1) 11.1
Power (watts)(1) 2,310
Btu/h(2) 7,900
Power cord type and length
SJT, 6-20P, 10ft
Hardwire Field-congurable
Breaker size 20 amp
CFM 830
Dimensions:
Width: 32⅝"
Height: 24"
Length: 24¼"
Weight 180 lbs.
Operating range Temp/RH 60/50 to 85/80
(1)Rated capacity and energy factor test done and current draw measured in accordance
with AHAM DH-1 2008 at 80°F/60% RH inlet air at 0.0 ESP, 208 VAC.
(2)Total cooling load @ 80°F/60% RH.
PRINCIPLE OF OPERATION
The Anden Model A320V1 Dehumidier is designed to dehumidify
the air coming into the unit by passing the incoming air over an
evaporator coil to drop the air temperature below the dew point of
the air. Moisture is removed from the air and drained out of the unit
to a common oor or waste drain. The air is then reheated in the
condenser coil and exits the unit.
Dehumidication occurs until the set point is reached, then shuts
o until the control determines a need for operation.
APPLICATION
The Anden Model A320V1 Dehumidier is the perfect solution
for the precise management of humidity required in an indoor
growing environment.
High-Capacity Grow-Optimized
Dehumidifier
Model A320V1 | Specification Sheet
INCLUDED ITEMS
Control Model A77
Drain ttings
¾" MNPT x ¾” BARB,
¾" MNPT x ¾” Female pipe,
¾" FNPT x ¾” Female pipe,
¾" P-Trap
Drain tubing (length, ID) 10' – ¾" ID
Thermostat wire 30’ 20 gauge 4-wire
MODEL A77
Dedicated monitoring and control of
each dehumidier at canopy height
INCLUDED CONTROL
MODEL A77 SPECIFICATIONS
Electrical
Input voltage
and current
Voltage: 35VDC (supplied by
dehumidier control board)
Output Communication (RS485)
Control
Control range 35%–80% RH
Accuracy +/-5% RH
Dierential 3% RH
Low limit 40°F dew point
High limit 99°F dry bulb

Form. No. 6540 • 310969 01.22
© 2022 Anden | anden.com | 800.972.3710
Anden reserves the right to change specifications without notice.
Drain Requirements
Placement
The Model A320V1 has a negative pressure cabinet that
requires a vented drain and drain trap (both included). The
drain lines should have a constant downward slope all the
way to the oor drain or condensate pump. The end of
the drain line should not be submerged in water to avoid
microbial growth.
Included:
• ¾ PVC drain trap
• ¾ PVC Vent T
• PVC Connectors
Model A77 Control (Included) External Control w/ Dry Contacts
The Model A320V1 can be controlled with the Model A77 Control (included) or any external control that can provide a
dry contact closure. When the Model A77 is used, the User Interface on the dehumidier MUST BE set to “Remote”.
For all other external controls, the User Interface MUST BE set to “External”. Refer to the quick start guide or installation
manual for instructions on accessing the installer set-up menu.