Andrew James 4 Day Automatic Pet Feeder User manual

1
Please read the instrucon manual carefully and keep it for future reference.
4 Day Automac Pet Feeder

2
Contents page
Control panel Page 3
Features Page 3
Appliance components illustraon Page 4
Disassemble Page 5
Assembling the appliance Page 6
Filling the bowl with food Page 7
Geng started Page 8
Seng the current clock me Page 8
Seng the feeding me Page 9
Review and start the feeding mer Page 10
Display mode Page 10
Recorded voice message to be played at
feeding me
Page 10
Baery replacement Page 10
Notes & FaQ Page 11
UK & EU Guarantee Page 12
Contact details Page 13

3
Control Panel
 MODE - switches between clock or feeding me display. Also increases clock
me during clock / feeding me set mode.
 SET – enters sengs mode. Also conrms the me you enter and advances
to next seng.
 START NOW – starts the feeding mer immediately.
 START TOMORROW- starts the feeding mer the next day.
 REC – records your personal voice message.
 PLAY – plays back your recorded voice message.
 ON SWITCH – turns the feeder on / o. For when the feeder will not be used
for an extended period of me. Turning this switch o will RESET all me
and feeding sengs.
Features
 24 hour clock display.
 6 second personal voice message recorder.
 Personal Voice message calls your pet when its feeding me.
 Food Bowl rotates according to your set me.
 The 4 Feeding mes can be set for any me of day or night.
 C size alkaline baeries (4pc’s required) not required.
 Red LED indicates low baeries.
 Extra compartment top for ice-pack or water.

4
Appliance components illustraon
A. Bowl cover D. Food bowl
B. Inner bowl cover E. Hob
C. Slide cover F. Feeder base

5
Disassemble
1. Remove the bowl cover (A) by forcefully liing the lid from underneath.
2. Remove the inner bowl (B).
3. Remove the slide cover (C).
Oponal: Remove the feedings trays from the feeding base (D) the appliance can be
used with or without the trays and rmly push down.

6
Re-assembling the appliance
1. Fit the food bowl (D) so that it locks with the Hub (E) located in the feeder
base (F).
2. Place the Inner feeding trays into the food bowl (D) this is oponal.
3. Fit the slide cover (C) onto the top of the food bowl (D).
4. Fit the inner bowl (B) onto the feeder so that it locks with the slide cover (C).
5. Secure the Bowl cover (A) onto the appliance by lining up the ngs.

7
Filling the bowl with food
1. Please disassemble the appliance rst.
2. Fill the food bowl (D) with the required amount of food (the appliance can
be used either with or without the food trays).
3. Place the slide cover (C) onto the appliance so that it ts the grooves.
4. Aach the Inner bowl (B) so that it ts with the slide cover. You can now ll
the ice compartment if required (C) .
5. Fit the bowl cover (A) accordingly.

8
Geng started
1. Carefully turn the pet feeder upside down. Remove both baery doors by
squeezing the two tabs and gently pull each door away.
2. Keep the ON switch set to OFF. Insert four C size alkaline baeries into the
baery tray. DO NOT use old or cheap carbon baeries.
3. Close the baery doors, rotate the feeder right-side up and switch ON The
feeder will cycle one me unl “12:00” is on the LCD display.
Note: Your pet feeder makes the food available in this sequence: Tray 1, Tray 2,
Tray 3 then Tray 4. When only one feed is required only ll Tray 1. For two feeds
Tray 1 and 2. Connue the sequence on for further feeds.
Seng the current Clock me
1. Press and hold the SET key for (2 seconds) to enter Clock SET mode. The
hour number will now begin to blink.
2. Press the MODE key to increase the hour. Once you have set the hour,
press the SET key to conrm the hour. The minute number will now blink.
3. To change the minute number, press the MODE key to increase the
minute. Once you have set the minute, press the SET key to conrm the
minute. Both the hour and minute numbers will now blink.
4. If needed, Press the MODE key to change between 12 or 24 hour me.
5. Press the SET key to conrm your current me seng and the numbers
will stop blinking.

9
Seng the Feeding Time
1. Aer seng the clock me, press the MODE key one me. (1 1) will show
on the display. This is the feeding-me display mode.
2. Now press and hold the SET key for (2 seconds) to enter the Feeding me
SET mode. Feeding will start from the rst feeding number & me. The 1st
digit shows the feeding number (Food Tray 1).
3. The hour digit will now blink (2nd and 3rd digit). Press the MODE key to
increase the me, then press the SET key to conrm the set me.
4. Aer conrming the feeding me you just set, the next feeding number &
me will show on the display (1st digit will change to the next feeding
number, e.g. 2 or 3 or 4 and back to 1). To change the feeding me, repeat
step 3.
5. Repeat step 3 unl all 4 feeding mes are set. The display will change back to
clock display mode when all 4 feeds have been set.
1st digit 2nd digit 3rd digit
Feeding
Number
Feeding
Time
Program examples:
 Feed once a day at 13:00hr (24hrs display) and feed for 4 days
 Feed me 1 & 2 & 3 & 4 = 13:00hr
 Feed twice a day at 10:00 and 20:00 and feed for two days
 Feed me 1 = 10, feed me 2 = 20, feed me 3 = 10 and feed me 4 = 20
 Feed four mes a day at 6:00, 11:00, 16:00 and 21:00
 Feed me 1 = 06, feed me 2 = 11, feed me 3 = 16 and feed me 4 = 20
Please note that the feeder will start from the closest me for example if its 13:00
and your feeder has been set to feed at 8:00, 12:00, 15:00 and 18:00 it will start
from 13:00.

10
Review and Start the feeding mer
1. Use the MODE key to cycle through the clock and your set feeding mes
(clock - then 1st feed me→2nd feed me→3rd feed me→ 4th feed me→
back to clock…) The sequence will repeat.
2. Press the START NOW key to start the feeding mer immediately. The bowl
will rotate to the pre-set starng posion (Tray 4) and your recorded
message will play once. The BELL icon will now be seen in the LCD display.
3. Alternavely press the START TOMORROW key and the feeding mer will
start at 0:00-Midnight. The bowl will rotate to the pre-set starng posion
(Tray 4) and your recorded message will play once. The BELL and Zz icon will
now be visible in the LCD display.
Display Mode (to check feeding mes you have set)
Use the MODE key to cycle through clock and feeding sengs (clock - then 1st feed
me→2nd feed me→3rd feed me→ 4th feed me→ back to clock…) The
sequence will repeat.
When the pet feeder runs out of food, just rell it. You do not need to go through
the mer process again.
Record Voice Message to be played at feeding mes
1. Press and hold the REC key, the Red LED will turn on.
2. Speak your message. You have up to 20 seconds.
3. When nished release the REC key.
4. Play back recorded Voice Message.
Press the PLAY key.
Your recorded message will now play.
At each Feeding your recorded message will play back 3 mes.
Baery Replacement
Change all baeries when the Red LED (Low baery indicator) ashes. Use only new
Alkaline baeries.

11
Notes and FAQ’S:
1. When the bowl is rotang both the clock seng and mode seng are not
allowed.
2. Under clock display mode the colon icon (:) will ash. The colon icon (:) is
turned O when in feeding mer mode.
3. A PM icon will be displayed in the aernoon under 12-hour clock mode
and turned o in the AM. The PM icon will not be displayed under 24 hour
clock mode.
4. In feeding mer mode, three numbers will show up, the rst number is the
feeding number (1,2,3,or 4) and last two digits indicate the feeding me in
hours.
5. When the feeding mer starts, the BELL icon will turn on. Under feeding-
mer display mode a solid BELL icon means the feeding me has already
passed. A ashing BELL icon means the feeding me has not been reached.
This lets the user know how many feedings are le for feeding.
6. If the me for the next feeding is set earlier than the present feeding me,
the feeding will start the next day.
7. If the Mode key is pressed and held for more than 2 seconds the number
will rapidly increase automacally unl you release the key. When number
reaches its maximum, the number will fall back to the minimum value and
start increasing again.
8. If the feeding mer has already begun, pressing the START key will reset
the mer and begin again from the 1st feeding-me set.
9. If START TOMORROW key is pressed, both the BELL and Zz icon will be ON.
The Zz icon will turn OFF at 0:00 midnight to indicate the mer has started.
10. START TOMORROW is used should you want to set your feeder up today
and have it start tomorrow. This is good for when you have programmed
feeding mes that have yet to pass so you can prepare in advance for a
possible trip or just being away the next day and not wanng the feeder to
run the day you programmed it.

12
UK and EU Guarantee
Your new Andrew James product comes with a 24 month guarantee and a 2 year
xed warranty, eecve from receipt conrmaon. Your receipt or order number is
required as proof of purchase date so it is imperave that you keep it safe. This
guarantee only applies if the item has been used solely for the use intended, and all
instrucons have been followed accordingly. Please note this product is only for
domesc not commercial use. Abuse of your product will invalidate the guarantee.
Returned goods can only be accepted if repackaged properly within the original
colour product box, and presented with the original receipt of sale/order number.
This does not aect your statutory rights. Returned products must be cleaned and
returned to us in as close to delivery condion as possible. If your product develops
a problem within the rst 12 months of the xed warranty, we will pay all shipping
costs to have it returned to us. Aer 12 months the customer will be liable for the
cost of returning the product to us. We will then pay to have the repaired/replaced
item shipped back to the customer. If you wish to return your item for a full refund,
you have the right to do so within the rst 7 days.
For our returns policy please go to www.andrewjamesworldwide.com
Customers are responsible for any taxes applied to our products when they are
shipped outside of the EU.
All of our prices are inclusive of VAT.
Once a product has been returned to us, we will aim to repair or replace it within
30 days of receipt.
The guarantee does not cover any defect arising from improper use, damage, build-
up of lime scale or repair aempts made by third-pares. Also, the guarantee does
not cover normal wear and tear of individual parts.