Animo PRIMO MAXI User manual

QUICK REFERENCE GUIDES
FOR
PRIMO MAXI
POST DEC 2015
&
2011 - 2015

PRIMO MAXI
QUICK REFERENCE
POST
DEC 2015

18
OptiBean NG /OptiBean XL NG
2015/11 Rev. 0.0
2.6 Adjustment tips
Cream layer too low Cream layer perfect Cream layer missing or too light
- Grind too fine
- Bitter
- Preparation too long
-Too much ground dosing
- Coffee drips from splitter
The coffee is ground too fine,
or the dispensed coffee is
too high. The extraction is
too extreme due to a too long
contact time. (to many bitter
substances).
Advice: set the coffee grinder
coarser (adjustment anti-
clockwise). Also shorten the
coffee dosing by 0.1 sec.
Note!
When setting the grinder
coarser there is a risk of excess
measurement (coffee volume/
weight increases) as a result
of which the espresso group
can jam.
- The right grind
- Perfect coffee taste
-The right preparation time
-The right coffee measurement
- Coffee sprays full and parallel
The coffee is ground well, the
taste extraction is optimal. The
cream layer is firm and persists
for a long time.
Advice: enjoy your coffee
- Grind too coarse
- Weak
- Preparation too short
-To low ground coffee dosing
- Coffee sprays bent outwards
The ground coffee is too coarse
for reaching a good extraction.
The coffee will be under-
extracted. Little or no cream
layer.
Advice: set the coffee grinder
finer (adjustment clockwise).
Adjust the grind setting only in
steps of a maximum 1/4 turn
each time. Only the 3rd cup of
coffee is 100% made with the
changed grind fineness! (do not
measure the first 2).

20
OptiBean NG /OptiBean XL NG
2015/11 Rev. 0.0
3. PRINCIPLES OF OPERATION
Item Description Item Description
1. Coffee waste bin 12. KW2 Pump 10 bar
2. Drainage reservoir 13. KW1 Inlet valve
3. BM1 Espresso group (reversed) 14. PR Pressure reducer 2 bar
4. IM1 Coffee grinder 15. FL1 Flow meter
5. Coffee bean canister 16. DV1 Brewer valve
6. DV6 Expansion water valve + OPV 3 bar 17. IM2-3 Canister drive motor
7. DV2 Mixer valve 3/2 way 18.
Cassette moisture extraction
8. DV4 Hot water valve 3/2 way 19. MM2 Mixer system
9. OPV2 Pressure relief valve 12 bar 20. Fan
10. Instant canisters 21. Hot water outlet
11. H2-3 Pressure boiler 22. Coffee / Drink outlet
3
1
4
5
2
67 8 9
16
10 17
11 19
18
15
12
13
14
20
21
22

31
2015/11 Rev. 0.0
EN
OptiBean NG /OptiBean XL NG
3.4.2 Espresso brewer spec’s
Standard brewer XL Brewer
Ø 37mm
min. 0,23 - max. 0,35* Ounces
min. 50 - max. 150 ml
* max. 9,0 gram
!* max. 9,5 gram
20-30 sec.
120-150ml
Standard
min. 1,8  oz - max. 5,3  oz
* max. 0,32 Ounces
!* max. 0,34 Ounces
min. 6,5 - max. 9,5* gram
1,8-15,3 uid Ounces
ax. 0,35* Ounc
x. 9,5* gram
Ø 44mm
min. 0,34 - max 0,47* Ounces
min. 150 - max. 230 ml
* max. 12,5 gram
* max. 13,4 gram
!
30-40 sec.
150-230ml
XL
min. 5,3 - max. 8,1  oz
* max. 0,44 Ounces
* max. 0,47 Ounces
!
min. 9,5 - max 13,4* gram
5,3-8,1 uid Ounces
ax 0,47* Ounce
x 13,4 gram

31
2015/11 Rev. 0.0
EN
OptiBean NG /OptiBean XL NG
3.4.2 Espresso brewer spec’s
Standard brewer XL Brewer
Ø 37mm
min. 0,23 - max. 0,35* Ounces
min. 50 - max. 150 ml
* max. 9,0 gram
!* max. 9,5 gram
20-30 sec.
120-150ml
Standard
min. 1,8  oz - max. 5,3  oz
* max. 0,32 Ounces
!* max. 0,34 Ounces
min. 6,5 - max. 9,5* gram
1,8-15,3 uid Ounces
ax. 0,35* Ounc
x. 9,5* gram
Ø 44mm
min. 0,34 - max 0,47* Ounces
min. 150 - max. 230 ml
* max. 12,5 gram
* max. 13,4 gram
!
30-40 sec.
150-230ml
XL
min. 5,3 - max. 8,1  oz
* max. 0,44 Ounces
* max. 0,47 Ounces
!
min. 9,5 - max 13,4* gram
5,3-8,1 uid Ounces
ax 0,47* Ounce
x 13,4 gram

31
2015/11 Rev. 0.0
EN
OptiBean NG /OptiBean XL NG
3.4.2 Espresso brewer spec’s
Standard brewer XL Brewer
Ø 37mm
min. 0,23 - max. 0,35* Ounces
min. 50 - max. 150 ml
* max. 9,0 gram
!* max. 9,5 gram
20-30 sec.
120-150ml
Standard
min. 1,8  oz - max. 5,3  oz
* max. 0,32 Ounces
!* max. 0,34 Ounces
min. 6,5 - max. 9,5* gram
1,8-15,3 uid Ounces
ax. 0,35* Ounc
x. 9,5* gram
Ø 44mm
min. 0,34 - max 0,47* Ounces
min. 150 - max. 230 ml
* max. 12,5 gram
* max. 13,4 gram
!
30-40 sec.
150-230ml
XL
min. 5,3 - max. 8,1  oz
* max. 0,44 Ounces
* max. 0,47 Ounces
!
min. 9,5 - max 13,4* gram
5,3-8,1 uid Ounces
ax 0,47* Ounce
x 13,4 gram

20
OptiBean NG /OptiBean XL NG
2015/11 Rev. 0.0
3. PRINCIPLES OF OPERATION
Item Description Item Description
1. Coffee waste bin 12. KW2 Pump 10 bar
2. Drainage reservoir 13. KW1 Inlet valve
3. BM1 Espresso group (reversed) 14. PR Pressure reducer 2 bar
4. IM1 Coffee grinder 15. FL1 Flow meter
5. Coffee bean canister 16. DV1 Brewer valve
6. DV6 Expansion water valve + OPV 3 bar 17. IM2-3 Canister drive motor
7. DV2 Mixer valve 3/2 way 18.
Cassette moisture extraction
8. DV4 Hot water valve 3/2 way 19. MM2 Mixer system
9. OPV2 Pressure relief valve 12 bar 20. Fan
10. Instant canisters 21. Hot water outlet
11. H2-3 Pressure boiler 22. Coffee / Drink outlet
3
1
4
5
2
67 8 9
16
10 17
11 19
18
15
12
13
14
20
21
22

18
OptiBean NG /OptiBean XL NG
2015/11 Rev. 0.0
2.6 Adjustment tips
Cream layer too low Cream layer perfect Cream layer missing or too light
- Grind too fine
- Bitter
- Preparation too long
- Too much ground dosing
- Coffee drips from splitter
The coffee is ground too fine,
or the dispensed coffee is
too high. The extraction is
too extreme due to a too long
contact time. (to many bitter
substances).
Advice: set the coffee grinder
coarser (adjustment anti-
clockwise). Also shorten the
coffee dosing by 0.1 sec.
Note!
When setting the grinder
coarser there is a risk of excess
measurement (coffee volume/
weight increases) as a result
of which the espresso group
can jam.
- The right grind
- Perfect coffee taste
- The right preparation time
- The right coffee measurement
- Coffee sprays full and parallel
The coffee is ground well, the
taste extraction is optimal. The
cream layer is firm and persists
for a long time.
Advice: enjoy your coffee
- Grind too coarse
- Weak
- Preparation too short
- To low ground coffee dosing
- Coffee sprays bent outwards
The ground coffee is too coarse
for reaching a good extraction.
The coffee will be under-
extracted. Little or no cream
layer.
Advice: set the coffee grinder
finer (adjustment clockwise).
Adjust the grind setting only in
steps of a maximum 1/4 turn
each time. Only the 3rd cup of
coffee is 100% made with the
changed grind fineness! (do not
measure the first 2).

87
2015/11 Rev. 0.0
EN
OptiBean NG /OptiBean XL NG
9.1.3 Main circuit board communication
The machine has standardized vending machine con-
nections for connecting coin mechanism, coin changer
or cashless payment systems.
These connectors meet the MDB protocol for vending
machines.
For further information or advice please contact our
support department.
Communication
Conn Protocol Notes
G13 Parallel interface
art. no. 04025 03267
-Coin acceptor NRI G13
- External release contact*
*the machine can be released by using a potential-free
contact (pulse).
- G13 Kabel 1 meter art. no. 03392
- Extern vrijgave contact; kabel 1004237
MDB Serial interface
MDB (Multi Drop Bus)
art. no. 03433
-Coin changer NRI C2
- Cashless payment system
- Telemetry EVA DTS (SD card needed)
Memory Card
- MDB cable 1 meter art. no. 03479
- MDB cable 1 meter art. no. 1004564 (2x male connector)
- MDB Y-kabel art.no. 1002008
RS232-2 Serieel interface
DEX UCS
new from sept 2015 -Telemetry EVA DTS / DEX UCS (SD card needed)
Memory Card
RS232 not used
G13
MDB
COMMUNICATION
RS232
RS232-2
CSI

88
OptiBean NG /OptiBean XL NG
2015/11 Rev. 0.0
9.2 Interface / Display
The interface connects all the components located in
and on the door and is connected by a cable to the
main control.
9.2.1 Connections
Interface & Display
Conn Notes
J100 Main control
J101 Front membrane panel
J102 Service membrane panel
J103 Key switch
J104 Jumper position A-B A = cup sensor; no
B = cup sensor; yes
J105 Display connection See dismantling instructions
J106 RGB LED
J107 RGB LED
J108 - not used
J109 Backlight display
J110 - not used
J112 cup sensor left coffee spout position
J113 cup sensor middle
J114 cup sensor right hot water spout position
J200 SD card holder
Memory Card
J103
Key
J200
SD CARD
J114
Cup
detc.
Right
J112
Cup
detc.
Left
J102
Service
panel
J101
Membrane
Switch
J107
RGB
LED
J106
RGB
LED
J109
Back
Light
LCD
J105
Display
First
Unlock!
LCD atcable
connector
First
Unlock!
J104
Jump
Back Light LCD
LCD
J100
Main
Board
A
B

89
2015/11 Rev. 0.0
EN
OptiBean NG /OptiBean XL NG
9.3 Power supply
The 24 Vdc supply consists of a 24 Vdc – 65 W
switched power supply and can be accessed by
removing the rear wall.
● On an overload, the power supply switches itself off
automatically. Reset the power supply by turning the
main switch off and on again.
9.3.1 Connections
Connector TB2 24Vdc
Pin Col-
our
Comments
1-3 24 Vdc + red
4-7 24 Vdc - black
8 - -
Connector TB1 100-240Vac
Pin Col-
our
Comments
1 230 Vac Neutral blue
3 230 Vac Phase yellow
Fuse F1 4A slow art.no. 1004957
+24V GND
100-240 Vac
J1
J2
1
F4,0A T
F1

90
OptiBean NG /OptiBean XL NG
2015/11 Rev. 0.0
9.4 Grinder print 230Vac / 230Vdc
This grinder circuit board converts 230 Vac (alternating
current) into 230 Vdc (direct current) with a rectifier to
drive the grinder motor.
The IM1 signal (24 Vdc) from the main control is
connected to connection J5-J6 (the red LED lights). This
signal controls the grinder motor with a triac.
This control can be accessed by removing the rear wall.
● Fuse 3.15 A S art.no. 02580; to protect the grinder
motor.
9.4.1 Connections
24 Vdc ingredient 1 signal
Pin Colour Notes
J5 24Vdc + red
polarity not important
J6 24Vdc - brown
230Vdc
Pin Colour Notes
1 230Vdc + red
polarity is important!
3 230Vdc - black
230Vac
Pin Colour Notes
J2 230 Vac Zero blue
J3 PE (ground) y/gr/
J4 230 Vac Phase brown
Fuse F1
3.15 A slow blow art.no. 02580
Grinder motor 230Vdc
Pin Colour Notes
230 Vdc + red Note the right
direction!
+24 Vdc (red wire)
according to drawing
230 Vdc - black
+
RED
-
BLACK
F 3,15A T
230Vac
J6J5
LED
J3J2 J4
PE
F1
Grinder
motor
230Vdc
24Vdc
grinder
signal
LN
+
_
J7

91
2015/11 Rev. 0.0
EN
OptiBean NG /OptiBean XL NG
10. FAULT RECTIFICATION
WARNING
● When there are defects and for (cleaning) activities on the machine, the plug must be removed
from the wall socket before the machine is opened
Introduction
Check, before troubleshooting whether all the components are still in the right location. To do this,
remove the rear wall of the machine and check that all circuit boards, connectors, wiring looms and
hoses are still properly mounted.
After a general inspection of the components, use the fault analysis table below to check what the
possible cause of the problem is.
#) If the ‘solution’ column advises replacing the component concerned, there is always the possibility
that the defect is caused by another problem. Therefore, test the machine thoroughly for operation to
check whether the defect occurs again.
10.1 Read log
During use, the last 20 error messages displayed
are registered and saved.
To read these error messages, activate the menu item Read
log (menu 2.8) in the service menu. The first error displayed is
the most recent error message.
•In the 1st line the same error codes are displayed as used
in the fault analysis table (see Section 10.4).
• In the 2nd line are the date and time at which the error
code occurred.
10.2 Erase log
Use the Clear log function (service menu 2.9) to clear the log.
Number Trouble code
Date Time
01: EXX
06-09-12 10:10

92
OptiBean NG /OptiBean XL NG
2015/11 Rev. 0.0
10.3 Display messages during use
Display Possible cause Action
Make your choice
Rinsing
Rinse program not activated in
time.
Run the rinse program and follow
the instructions in the display.
See chapter 6. Maintenance / 6.1
daily rinsing program
Make your choice
Cleaning
Cleaning program is not activated
in time.
Run the cleaning program and fol-
low the instructions in the display.
See chapter 6. Maintenance / 6.2
Weekly rinsing program
Make your choice
Service boiler
Boiler needs maintenance. See chapter 6.3 Periodic maintenance /
6.3.1 Service boiler.
Make your choice
Service brewer
Brewer needs maintenance. See chapter 6.3 Periodic maintenance /
6.3.2 Service brewer and 5.4.4 Servicing
Out of order
Boiler filling
When used for the first time: boiler
is still empty and is being filled.
No action needed. Follow the instructions
on the display. When the boiler is filled,
‘Boiler heating’ follows.
Out of order
Boiler heating
The boiler temperature is
(temporarily) too low because too
much water has been used.
Once the temperature is restored, the mes-
sage automatically disappears and the drink
selection buttons are reactivated.
If this text remains in view for 6
minutes, an E21 boiler time out
follows.
See E21 boiler timeout.
Out of order
Drip tray full
Drip tray full.
Once the drip tray is emptied, the message
automatically disappears and the drink
selection buttons are reactivated.
Out of order
Waste bin full
The maximum number of coffee
cups that the waste bin can hold
has been reached.
Empty waste bin. The cup counter is
automatically reset when the waste bin is
replaced.
Out of order
Waste bin missing
Waste bin is not detected. Check the waste bin.

93
2015/11 Rev. 0.0
EN
OptiBean NG /OptiBean XL NG
Display Possible cause Action
Out of order
Door open
For safety reasons, the machine
automatically switches off if the
door is opened.
The machine can be operated with the door
open by using the door pin.
Out of order
Stand-by
The machine is on standby. This function can be set manually or auto-
matically.
Close door
Door lock not closed properly.
Hot water dispensing not possible. Close door lock.
Out of order
Rinsing
Rinse program not activated in
time. The machine locks up.
Run the rinse program and follow
the instructions in the display.
See chapter 6. Maintenance / 6.1
daily rinsing program
Out of order
Cleaning
Cleaning program is not activated
in time. The machine locks up.
Run the cleaning program and fol-
low the instructions in the display.
6. Maintenance / 6.2 Weekly
rinsing program
Coffee
Place cup
no cup positioned under the spout. position a cup under the spout.
Coffee
place cup under
correct outlet
no cup positioned under the
correct the spout. position a cup under the correct spout.
your drink has
canceled the cup was taken away to quickly keep the cup in position during the drink
preparation.

PRIMO MAXI
QUICK
REFERENCE
PRE
2011 - 2015

QUICK REFERENCE – PRIMO MAXI 2011 - 2015
1
2

QUICK REFERENCE – PRIMO MAXI 2011 - 2015
BREWER CAPACITY
37mm 6.5g – 9.0g MAX
44mm 9.5g – 12.5g MAX
1057151
1057167
3
4

QUICK REFERENCE – PRIMO MAXI 2011 - 2015
5
6