Anritsu MU120119A User manual

Document No.: M-W2121AE-12.0
ANRITSU CORPORATION
MU120119A
OC-3/12 STM-1/4 (1310 nm) Module
MU120120A
OC-3 STM-1 (1310 nm) Module
Operation Manual
12th Edition
•
For safety and warning information, please read this
manual before attempting to use the equipment.
•Additional safety and warning information is
provided within the MD1230B Data Quality Analyze
r
Operation Manual or MP1591A Network Performanc
e
Tester Operation Manual. Please also refer to this
document before using the equipment.
•Keep this manual with the equipment.

ii
Safety Symbols
To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the
following safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings
of the symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu
equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this
manual.
Symbols used in manual
This indicates a very dangerous procedure that could result in serious injury or
death if not performed properly.
This indicates a hazardous procedure that could result in serious injury or death if
not performed properly.
This indicates a hazardous procedure or danger that could result in light-to-severe
injury, or loss related to equipment malfunction, if proper precautions are not taken.
Safety Symbols Used on Equipment and in Manual
The following safety symbols are used inside or on the equipment near operation locations to provide information
about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols
and take the necessary precautions BEFORE using the equipment.
This indicates a prohibited operation. The prohibited operation is indicated
symbolically in or near the barred circle.
This indicates an obligatory safety precaution. The obligatory operation is
indicated symbolically in or near the circle.
This indicates a warning or caution. The contents are indicated symbolically in or
near the triangle.
This indicates a note. The contents are described in the box.
These indicate that the marked part should be recycled.
MU120119A OC-3/12 STM-1/4 (1310 nm) Module
MU120120A OC-3 STM-1 (1310 nm) Module
Operation Manual
1 April 2003 (First Edition)
1 August 2008 (12th Edition)
Copyright © 2003-2008, ANRITSU CORPORATION.
All rights reserved. No part of this manual may be reproduced without the prior written permission of the
publisher.
The contents of this manual may be changed without prior notice.
Printed in Japan
DANGER
WARNING
CAUTION

iii
Equipment Certificate
Anritsu Corporation certifies that this equipment was tested before
shipment using calibrated measuring instruments with direct
traceability to public testing organizations recognized by national
research laboratories, including the National Institute of Advanced
Industrial Science and Technology, and the National Institute of
Information and Communications Technology, and was found to meet the
published specifications.
Anritsu Warranty
Anritsu Corporation will repair this equipment free-of-charge if a
malfunction occurs within one year after shipment due to a manufacturing
fault, under the condition that this warranty is void when:
•The fault is outside the scope of the warranty conditions described in
the operation manual.
•The fault is due to mishandling, misuse, or unauthorized modification
or repair of the equipment by the customer.
•The fault is due to severe usage clearly exceeding normal usage.
•The fault is due to improper or insufficient maintenance by the
customer.
•The fault is due to natural disaster including fire, flooding,
earthquake, etc.
•The fault is due to use of non-specified peripheral equipment,
peripheral parts, consumables, etc.
•The fault is due to use of a non-specified power supply or in a
non-specified installation location.
In addition, this warranty is valid only for the original equipment
purchaser. It is not transferable if the equipment is resold.
Anritsu Corporation shall assume no liability for injury or financial loss of
the customer due to the use of or a failure to be able to use this equipment.
Anritsu Corporation Contact
In the event that this equipment malfunctions, contact an Anritsu
Service and Sales office. Contact information can be found on the last
page of the printed version of this manual, and is available in a separate
file on the CD version.

iv
Notes On Export Management
This product and its manuals may require an Export License/Approval by
the Government of the product's country of origin for re-export from you
r
country.
Before re-exporting the product or manuals, please contact us to confirm
whether they are export-controlled items or not.
When you dispose of export-controlled items, the products/manuals need
to be broken/shredded so as not to be unlawfully used for military purpose.
Notice
The following actions are strictly prohibited for all of the software
installed in this product or otherwise provided by Anritsu:
1. Copying, except for archival purposes,
2. Transferring to a third party apart from this product,
3.
A
nalyzing the incorporated software including but not limited to
modifying, decompiling, disassembling, and reverse engineering.

v
CE Conformity Marking
Anritsu affixes the CE Conformity marking on the following product(s) in
accordance with the Council Directive 93/68/EEC to indicate that they
conform to the EMC and LVD directive of the European Union (EU).
CE marking
1. Product Model
Plug-in Modules: MU120119A OC-3/12 STM-1/4 Module (1310 nm),
MU120120A OC-3 STM-1 Module (1310 nm)
2. Applied Directive and Standards
When the above modules are installed in the main frame shown below,
the applied directive and standards of these modules conform to those
of the main frame.
Main frame: MD1230A/B Data Quality Analyzer,
MD1231A/A1 IP Network Analyzer,
MT7407A Multislot Chassis
MP1591A Network Performance Tester
PS: About main frame
Please contact Anritsu for the latest information on the main frame
types that the above modules can be used with.

vi
C-tick Conformity Marking
Anritsu affixes the C-tick marking on the following product(s) in
accordance with the regulation to indicate that they conform to the EMC
framework of Australia/New Zealand.
C-tick marking
1. Product Model
Plug-in Modules: MU120119A OC-3/12 STM-1/4 Module (1310 nm),
MU120120A OC-3 STM-1 Module (1310 nm)
2. Applied Directive and Standards
When the above modules are installed in the main frame shown below,
the applied directive and standards of these modules conform to those
of the main frame.
Main frame: MD1230A/B Data Quality Analyzer,
MD1231A/A1 IP Network Analyzer,
MT7407A Multislot Chassis
MP1591A Network Performance Tester
PS: About main frame
Please contact Anritsu for the latest information on the main frame
types that the above modules can be used with.

I
About This Manual
This operation manual is for MD1230 and MP1590 families.
Note:
MD1230 family is a general name for the MD1230A/B Data Quality
Analyzer, the MD1231A/A1 IP Network Analyzer, and the MT7407A
Multislot Chassis.
The MP1590 family is a general name for the MP1590B Network
Performance Tester and the MP1591A Network Performance
Tester.
Note that the MD1230A, MD1231A/A1, and MT7407A are not
supported in Ver. 7.0 and above.
The MD1230 family operation manuals consist of separate documents for
the main unit, control software, module(s), remote control operation, and
options, as shown below.
Configuration of MD1230
Family Operation Manual
indicates this document.
Describes basic operations of the MD1230B.
MD1230B Data Quality Analyzer
Operation Manual
Describes how to use the software that controls the
mainframe of the MD1230 family.
MX123001A Data Quality Analyzer Control Software
Operation Manual
Describes basic operations of Ethernet modules.
Ethernet Module
Operation Manual
Describes basic operations of SDH/SONET modules.
MU120103A/B 2.5G (1.31) Module
MU120104A/B 2.5G (1.55) Module
MU120105A 10G (1.31) Module
MU120106A 10G (1.55) Module
Operation Manual
MU120119A OC-3/12 STM-1/4 Module (1310 nm)
MU120120A OC-3 STM-1 Module (1310 nm)
Operation Manual
Describes remote control via RS-232C, GPIB, and
Ethernet interfaces.
MD1230B Remote Control
Operation Manual
Describes basic operations of SDH/SONET modules.

II
Describes how to operate the software for monitoring
Ethernet traffic.
A
pplication Traffic Monitor
Operation Manual
Describes basic operations of Decode modules.
Decode Module
Operation Manual
Describes basic operations of Tcl Interface.
Tcl Interface
Operation Manual
Describes basic operations of Expert Analysis modules.
Expert Analysis Module
Operation Manual

III
The MP1590 family operation manuals consist of separate documents for
the mainframe, module(s), control software, remote control operation, and
options, as shown below.
Configuration of MP1590
Family Operation Manual
MX159001B Network Performance Tester
Control Software Operation Manual SDH Edition
Describes how to operate the MP1590B control
software (SDH Edition).
Describes specifications for the EoS module.
Describes basic operations of the MP1591A.
Describes specifications for the SDH/SONET module.
MU150121A 10/10.7G Optical Unit (Tx)
MU150122A 10/10.7G Optical Unit (Rx Narrow)
MU150123A 10/10.7G Optical Unit (Rx Wide)
MU150134A 10/10.7G Optical Unit (Tx Ex. Mod)
Operation Manual
Describes specifications for the EO/OE modules.
indicates this document.
Describes specifications for the Jitter module.
MU150100A 10/10.7G Unit Operation Manual
MU150125A 10/10.7G Jitter Unit Operation Manual
MU150101A 2.5/2.6G EoS Unit Operation Manual
MP1591A Network Performance Tester
Operation Manual
MX159001B Network Performance Tester
Control Software Operation Manual SONET Edition
Describes how to operate the MP1590B control
software (SONET Edition).
MP1590B Network Performance Tester
Operation Manual
Describes basic operations of the MP1590B.

IV
Describes remote control via RS-232C, GPIB, and
Ethernet Interfaces.
MP1590B/MP1591A Network Performance Tester
Remote Control Operation Manual
Describes specifications for the MP1590A/B-30.
MP1590A/B-30 High Precision Jitter Analysis
Operation Manual
Describes how to operate the software for monitoring
Ethernet traffic.
A
pplication Traffic Monitor
Operation Manual
Ethernet Module
Operation Manual
Describes basic operations of Ethernet modules.
Describes basic operations of SDH/SONET modules.
MU120119A OC-3/12 STM-1/4 Module (1310 nm)
MU120120A OC-3 STM-1 Module (1310 nm)
Operation Manual
MU120103A/B 2.5G (1.31) Module
MU120104A/B 2.5G (1.55) Module
MU120105A 10G (1.31) Module
MU120106A 10G (1.55) Module
Operation Manual
Describes specifications for the MU150121B/23B.
MU150121B 10/10.7G Optical/Electrical Unit (Tx )
MU150123B 10/10.7G Optical/Electrical Unit (Rx Wide)
Operation Manual
Describes specifications for the MU150124B.
MU150124B 10.3G Optical/Electrical Unit (Rx Wide)
Operation Manual

V
This manual uses the following notations.
(1) Notation on equipment name
This manual uses the following abbreviations for the equipment
names.
Full Name Abbreviated Name
MD1230B Data Quality Analyzer MD1230B
MP1591A Network Performance Tester MP1591A
MU120119A OC-3/12 STM-1/4 Module (1310 nm) 156/622M Module
MU120120A OC-3 STM-1 Module (1310 nm) 156M Module
Note:
Note that the MD1230A, MD1231A/A1 and MT7407A are not sup-
ported in Ver. 7.0 and above.
Description in this manual shows the case of using the MD1230B.
(2) Notation on reference page
This manual indicates a related page, as below.
For details on specifications and functions, refer to the Appendix
“Specifications.”

VI
Table of Contents
About This Manual........................................ I
Section 1 Overview.................................... 1-1
1.1 Product Outline ............................................................. 1-2
Section 2 Precautions Before Use ........... 2-1
2.1 Installation Site Environmental Conditions ................... 2-2
2.2 Connection with Device Under Test ............................. 2-2
Section 3 Description of Panel ................. 3-1
3.1 Description of Panel...................................................... 3-2
Appendix A Specifications ......................... A-1
Index .......................................................... Index-1

1
VII
Index Appendix
2
3

VIII.

Section 1 Overview
1-1
1
Overview
This section describes an overview of the 156/622M POS module func-
tions.
For specifications, refer to the Appendix “Specifications.”
1.1 Product Outline .......................................................... 1-2

Section 1 Overview
1-2.
1.1 Product Outline
An MD1230B equipped with a 156/622M POS module can generate pack-
ets and transmit them over SONET/SDH, as well as analyze the incom-
ing packets. Each port operates at 156M or 622M individually.
(1) Available interfaces
The modules and their available interfaces are given below.
Modules Available interfaces (wave-length band)
MU120119A OC-3/12, 1310 nm, single mode
MU120120A OC-3, 1310 nm, single mode
(2) Number of ports
Each POS module has the number of ports listed below.
Modules
Number of
ports/module
Max. number
of
modules/unit
Max. number
of
ports/unit
Max. number of
ports for 8-unit
connection
MU120119A 2 5 10 80
MU120120A 2 5 10 80

Section 2 Precautions Before Use
2-1
2
Precautions Before Use
This section provides information to be understood before using the
156/622M POS modules. It also covers safety precautions and steps to
avoid malfunctioning of the device in use. Read through this section be-
fore using the POS modules.
2.1 Installation Site Environmental Conditions ................ 2-2
2.2 Connection with Device Under Test .......................... 2-2

Section 2 Precautions Before Use
2-2.
2.1 Installation Site Environmental Conditions
The 156/622M POS modules operate normally within a temperature
range of 0 to 40°C. Avoid using them under the following conditions to
prevent malfunctioning:
•Excessive vibration
•Excessive moisture or dust
•Direct sunlight
•Possible influence of active gas
•Severe temperature fluctuation
CAUTION
After using the 156/622 POS module for a long time in low
temperatures, moving them to a location with higher
temperatures may create dew inside the module. In this
event, sufficiently dehumidify the module before turning
the power On. Turning the power On when dew is present
inside may cause a short circuit and damage the module.
2.2 Connection with Device Under Test
When connecting a device being tested (Device Under Test: DUT), be sure
to check the input/output signal power level. Inputting a signal exceed-
ing the ratings may destroy the internal devices resulting in a failure.
Also avoid connecting output connectors to each other because it may
cause failure.

Section 3 Description of Panel
3-1
3
Description of Panel
This section describes the 156/622M POS module panel controls.
3.1 Description of Panel................................................... 3-2

Section 3 Description of Panel
3-2
3.1 Description of Panel
(1) MU120119A 156/622M Module (1310 nm)
The figure below shows the front panel of the 156/622M POS Module.
MU120119A
OC-3/12 STM-1/4 Module
Power Meter Port 2
Link
Tx
Error
Rx
Output Input
Port 1
Link
Tx
Error
Rx
Output Input
CLASS 1
LASER PRODUCT
!
Max +10 Bm
!
Max -8 Bm
!
Max -8 Bm
!
Fig. 3.1-1 156/622M POS Module
(2) MU120120A 156 Module (1310 nm)
The figure below shows the front panel of the 156 POS Module.
MU120120A
OC-3 STM-1 Module
Power Meter Port 2
Link
Tx
Error
Rx
Output Input
Port 1
Link
Tx
Error
Rx
Output Input
CLASS 1
LASER PRODUCT
!
Max +10 Bm
!
Max -8 Bm
!
Max -8 Bm
!
Fig. 3.1-2 156M POS Module
LED Color Description
Link Green
Lit when an SDH/SONET frame has been
received and LOS, LOF, or AIS alarms have
not been detected. Also lit when PPP
Negotiation (PPP) has succeeded.
Tx Green Lit when a PPP, Cisco HDLC or MAPOS
frame, or a bulk pattern is being sent.
Error Orange
Lit when an error has been detected.
For the error item detected, refer to the
table on the next page.
Rx Green Lit when a PPP, Cisco HDLC or MAPOS
frame, or a bulk pattern is being received.