Anritsu Network Master MT9090A Series User manual

Document No.: M-W3166AE-3.0
ANRITSU CORPORATION
Network Master Series
MT9090A
Mainframe
MU909060A Series
Gigabit Ethernet Module
Operation Manual
For safety and warning information, please read this
manual before attempting to use the equipment.
Keep this manual with the equipment.
Third Edition

ii
Safety Symbols
To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the
following safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of
the symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu
equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this
manual.
Symbols used in manual
This indicates a very dangerous procedure that could result in serious injury or
death if not performed properly.
This indicates a hazardous procedure that could result in serious injury or death if
not performed properly.
This indicates a hazardous procedure or danger that could result in light-to-severe
injury, or loss related to equipment malfunction, if proper precautions are not taken.
Safety Symbols Used on Equipment and in Manual
The following safety symbols are used inside or on the equipment near operation locations to provide information
about safety items and operation precautions. . Ensure that you clearly understand the meanings of the symbols
and take the necessary precautions BEFORE using the equipment.
This indicates a prohibited operation. The prohibited operation is indicated
symbolically in or near the barred circle.
This indicates an obligatory safety precaution. The obligatory operation is
indicated symbolically in or near the circle.
This indicates a warning or caution. The contents are indicated symbolically in or
near the triangle.
This indicates a note. The contents are described in the box.
These indicate that the marked part should be recycled.
Network Master Series
MT9090A Mainframe
MU909060A Series Gigabit Ethernet Module
Operation Manual
24 March 2009 (First Edition)
31 August 2009 (Third Edition)
Copyright © 2009, ANRITSU CORPORATION.
All rights reserved. No part of this manual may be reproduced without the prior written permission of the
publisher.
The contents of this manual may be changed without prior notice.
Printed in Japan
DANGER
WARNING
CAUTION

For Safety
iii
WARNING
1. ALWAYS refer to the operation manual when working near locations
at which the alert mark shown on the left is attached. If the advice in
the operation manual is not followed there is a risk of personal injury
or reduced equipment performance. The alert mark shown on the left
may also be used with other marks and descriptions to indicate other
dangers.
2. IEC 61010 Standard
The IEC 61010 standard specifies four categories to ensure that an
instrument is used only at locations where it is safe to make
measurements. This instrument is designed for measurement
category I (CAT I). DO NOT use this instrument at locations specified
as category II, III, or IV as defined below.
Measurement category I (CAT I):
Secondary circuits of a device that is not directly connected to a
power outlet.
Measurement category II (CAT II):
Primary circuits of a device that is directly connected to a power
outlet, e.g., portable tools or home appliance.
Measurement category III (CAT III):
Primary circuits of a device (fixed equipment) to which power is
supplied directly from the distribution panel, and circuits running from
the distribution panel to power outlet.
Measurement category IV (CAT IV):
Building service-line entrance circuits, and circuits running from the
service-line entrance to the meter or primary circuit breaker
(distribution panel).

For Safety
iv
WARNING
3. Laser radiation warning
•NEVER look directly into the cable connector on the equipment
nor into the end of a cable connected to the equipment. There is a
risk of injury if laser radiation enters the eye.
•The Laser Safety label is attached to the equipment for safety use
as indicated in "Laser Safety" later in this section.
4. This equipment cannot be repaired by the operator. DO NOT attempt
to remove the equipment covers or unit covers or to disassemble
internal components. Only qualified service personnel with knowledge
of electrical fire and shock hazards should service this equipment.
There are high-voltage parts in this equipment presenting a risk of
severe injury or fatal electric shock to untrained personnel. In addition,
there is a risk of damage to precision components.
5. The performance-guarantee seal verifies the integrity of the equipment.
To ensure the continued integrity of the equipment, only Anritsu
service personnel, or service personnel of an Anritsu sales
representative, should break this seal to repair or calibrate the
equipment. If the performance-guarantee seal is broken by you or a
third party, the performance of the equipment cannot be guaranteed.
Be careful not to break the seal by opening the equipment or unit
covers.
6. This equipment should always be positioned in the correct manner. If
the cabinet is turned on its side, etc., it will be unstable and may be
damaged if it falls over as a result of receiving a slight mechanical
shock.
Always set up the equipment in a position where the power switch
can be reached without difficulty.
Repair
Calibration
Falling Over

For Safety
v
WARNING
7. When replacing the battery, use the specified battery and insert it
with the correct polarity. If the wrong battery is used, or if the battery
is inserted with reversed polarity, there is a risk of explosion causing
severe injury or death.
8. DO NOT short the battery terminals and never attempt to disassemble
the battery or dispose of it in a fire. If the battery is damaged by any of
these actions, the battery fluid may leak. This fluid is poisonous.
DO NOT touch the battery fluid, ingest it, or get in your eyes. If it is
accidentally ingested, spit it out immediately, rinse your mouth with
water and seek medical help. If it enters your eyes accidentally, do
not rub your eyes, rinse them with clean running water and seek
medical help. If the liquid gets on your skin or clothes, wash it off
carefully and thoroughly.
9. This instrument uses a Liquid Crystal Display (LCD). DO NOT subject
the instrument to excessive force or drop it. If the LCD is subjected to
strong mechanical shock, it may break and liquid may leak.
This liquid is very caustic and poisonous.
DO NOT touch it, ingest it, or get in your eyes. If it is ingested
accidentally, spit it out immediately, rinse your mouth with water and
seek medical help. If it enters your eyes accidentally, do not rub your
eyes, rinse them with clean running water and seek medical help. If
the liquid gets on your skin or clothes, wash it off carefully and
thoroughly.
Replacing Battery
Battery Fluid
LCD

For Safety
vi
CAUTION
1. Never input a signal of more than the indicated value between the
measured terminal and ground. Input of an excessive signal may
damage the equipment.
Check Terminal

For Safety
vii
Class 1, 1M, 2, 2M, 3R, 3B and 4 indicate the danger degree of the
laser radiation specified below according to IEC 60825-1:2001.
Class 1: Lasers that are safe under reasonably foreseeable conditions
of operation, including the use of optical instruments for
intrabeam viewing.
Class 1M: Lasers emitting in the wavelength range from 302.5 to 4000
nm that are safe under reasonably foreseeable conditions of
operation, but may be hazardous if the user employs optics
within the beam. Two conditions apply:
a) for diverging beams, if the user views the laser output with
certain optical instruments (for example, eye loupes,
magnifiers and microscopes) within a distance of 100 mm;
or
b) for collimated beams, if the user views the laser output
with certain optical instruments (for example, telescopes
and binoculars).
Class 2, 2M, 3R, 3B and 4 does not apply.
CAUTION
Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
The use of optical instruments with this product will increase eye
hazard.

For Safety
viii
WARNING
The laser in the plug-in unit provided for this equipment is classified as
Class 1 according to the IEC 60825-1:2001 standard.
Table 1 Laser Safety Classifications Based on IEC 60825-1:2001
SFP Type Class Class 1 AEL (W) Pulse Width (s)/
Repetition Rate
Nominal
Wavelength (nm) Laser Aperture
LX and FX 1 0.0156 CW 1310 Figure 1,
1 or 2
ZX 1 0.01 CW 1550
Figure 1,
1 or 2
SX 1 0.000709 CW 850 Figure 1,
1 or 2
Laser Safety

For Safety
ix
Table 3 Indication Labels on Product (Ex: Label list)
Type Sample Affixed to: Model Name
1 Explanation Figure 1, C All
2 Certification Figure 1, B All
3 Identification Figure 1, A All
4 Warning Figure 1, D All

For Safety
x
Laser Radiation Markings
1 2
A
B
DC
Figure 1 Locations of Laser Beam Apertures and Affixed Labels

For Safety
xi
FOR EU & EFTA CUSTOMERS
Please Recycle.
Read the following when using products to which the mark shown on the
above is attached.
The product that you have purchased contains a rechargeable battery.
The battery is recyclable. At the end of its useful life, under various state
and local laws, it may be illegal to dispose of this battery into the
municipal waste. Check with your local solid-waste disposal officials for
details of recycling options or proper disposal in your area.
Before disposing of this product, discharge the battery and mail it to
your Anritsu Service or Sales office.
1. Disconnect the AC adapter, if used.
2. Turn the power switch to on.
3. Leave the product on until the power indicator goes off; the battery is
now discharged.
4. Remove the battery.
5. Insulate the battery terminals with adhesive tape.
6. Please recycle in accordance with your national or regional
legislation.
Nach gebrauch der Verkaufsstelle zurückgeben.
Après usage à rapporter au point de vente.
Ni-MH

For Safety
xii
CAUTION
This equipment uses USB flash drives as external storage media for
storing data and programs.
If this media is mishandled or becomes faulty, important data may be
lost. To prevent this chance occurrence, all important data and
programs should be backed-up.
Anritsu will not be held responsible for lost data.
Pay careful attention to the following points.
•Never remove the USB flash drive from the instrument while it is
being accessed.
•The USB flash drive may be damaged by static electric charges.
External
Storage Media

For Safety
xiii
CAUTION
This instrument is designed for an industrial environment.
In a residential environment this instrument may cause radio
interference in which case the user may be required to take adequate
measures.
Use in a residential
environment

xiv
Equipment Certificate
Anritsu Corporation certifies that this equipment was tested before shipment
using calibrated measuring instruments with direct traceability to public
testing organizations recognized by national research laboratories, including
the National Institute of Advanced Industrial Science and Technology, and
the National Institute of Information and Communications Technology, and
was found to meet the published specifications.
Anritsu Warranty
Anritsu Corporation will repair this equipment free-of-charge if a malfunction
occurs within one year after shipment due to a manufacturing fault, under the
condition that this warranty is void when:
•The fault is outside the scope of the warranty conditions described in the
operation manual.
•The fault is due to mishandling, misuse, or unauthorized modification or
repair of the equipment by the customer.
•The fault is due to severe usage clearly exceeding normal usage.
•The fault is due to improper or insufficient maintenance by the customer.
•The fault is due to natural disaster including fire, flooding, earthquake,
etc.
•The fault is due to use of non-specified peripheral equipment, peripheral
parts, consumables, etc.
•The fault is due to use of a non-specified power supply or in a
non-specified installation location.
In addition, this warranty is valid only for the original equipment purchaser. It
is not transferable if the equipment is resold.
Anritsu Corporation shall assume no liability for injury or financial loss of the
customer due to the use of or a failure to be able to use this equipment.
Anritsu Corporation Contact
In the event that this equipment malfunctions, contact an Anritsu Service and
Sales office. Contact information can be found on the last page of the printed
version of this manual, and is available in a separate file on the CD version.

xv
Notes On Export Management
This product and its manuals may require an Export License/Approval by
the Government of the product's country of origin for re-export from you
r
country.
Before re-exporting the product or manuals, please contact us to confirm
whether they are export-controlled items or not.
When you dispose of export-controlled items, the products/manuals need
to be broken/shredded so as not to be unlawfully used for military purpose.
Reuse parts
A
nritsu group promotes recycling activities in order to reuse available
resources and save energy. This product may use recycled parts
(mechanical components) that conform to Anritsu’s quality standards.

xvi
FOR CALIFORNIA USA ONLY
This product contains a CR Coin Lithium Battery which contains
Perchlorate Material – special handling may apply; See
www.dtsc.ca.gov/hazardouswaste/perchlorate

xvii
Crossed-out Wheeled Bin Symbol
Equipment marked with the Crossed-out Wheeled Bin Symbol complies with
council directive 2002/96/EC (the “WEEE Directive”) in European Union.
For Products placed on the EU market after August 13, 2005, please contact
your local Anritsu representative at the end of the product's useful life to
arrange disposal in accordance with your initial contract and the local law.

xviii
Notice
The following actions are strictly prohibited for all of the software
installed in this product or otherwise provided by Anritsu:
1. Copying, except for archival purposes.
2. Transferring to a third party separately from this product.
3. Analyzing the incorporated software including but not limited to
modifying, decompiling, disassembling, and reverse engineering.
Cautions against computer virus infection
•Copying files and data
Only files that have been provided directly from Anritsu or generated
using Anritsu equipment should be copied to the instrument.
A
ll other required files should be transferred by means of USB or
CompactFlash media after undergoing a thorough virus check.
•Adding software
Do not download or install software that has not been specifically
recommended or licensed by Anritsu.
•Network connections
Ensure that the network has sufficient anti-virus security protection in
place.

xix
CE Conformity Marking
Anritsu affixes the CE conformity marking on the following product(s) in
accordance with the Council Directive 93/68/EEC to indicate that they
conform to the EMC directive of the European Union (EU).
CE marking
1. Product Model
Model: MT9090A Mainframe
MU909060A1 Gigabit Ethernet Module RJ45 SFP
MU909060A2 Gigabit Ethernet Module RJ45 RJ45
MU909060A3 Gigabit Ethernet Module SFP SFP
2. Applied Directive
EMC: Directive 2004/108/EC
3. Applied Standards
•EMC: EN 300 386 TC and OTC
Performance Criteria*
IEC 61000-4-2 (ESD) B
IEC 61000-4-3 (EMF) A
IEC 61000-4-4 (Burst) B
IEC 61000-4-5 (Surge) B
IEC 61000-4-6 (CRF) A
*: Performance Criteria
A: During testing, normal performance within the
specification limits.
B: During testing, temporary degradation, or loss of
function or performance which is self-recovering.
C: During testing, temporary degradation, or loss of
function or performance which requires operator
intervention or system reset occurs.
Harmonic current emissions:
EN 61000-3-2: 2006 (Class A equipment)
: No limits apply for this equipment with an active input
power under 75 W.

xx
C-Tick Conformity Marking
Anritsu affixes the C-Tick mark on the following product(s) in accordance
with the regulation to indicate that they conform to the EMC framework of
Australia/New Zealand.
C-Tick mark
1. Product Model
Model: MT9090A Mainframe
MU909060A1 Gigabit Ethernet Module RJ45 SFP
MU909060A2 Gigabit Ethernet Module RJ45 RJ45
MU909060A3 Gigabit Ethernet Module SFP SFP
2. Applied Standards
EMC: Emission: EN 55 022, Class B