Antunes VCT-2 User manual

®
Mini Contact Toaster
Owner’s Manual
Model VCT-2
Manufacturing Numbers:
9210907, 9210924 , 9210955 & 9210919
www.antunes.com
Original Instructions
CAUTION: Read all instructions before using the unit. P/N 1011275 Rev. K 03/21

2
®
P/N 1011275 Rev. K 03/21
General
This manual provides the safety,
installation, and operating procedures
for your toaster. Please read all of the
information contained in this manual prior
to installing and operating the toaster.
Your toaster is manufactured from
the nest materials available and is
assembled to our strict quality standards.
This toaster was tested at the factory
to ensure dependable trouble-free
operation.
Warranty
Information
Please read the full text of the Limited
Warranty in this manual.
If the unit arrives damaged, contact the
carrier immediately and le a damage
claim with them. Save all packing
materials when ling a claim. Freight
damage claims are the responsibility of
the purchaser and are not covered under
warranty.
The warranty does not extend to:
yDamages caused in shipment or
damage as result of improper use.
yInstallation of electrical service.
yNormal maintenance as
outlined in this manual.
yMalfunction resulting from
improper maintenance.
yDamage caused by abuse
or careless handling.
yDamage from moisture into
electrical components.
Damage from tampering with, removal of,
or changing any preset control or safety
device.
Service/Technical
Assistance
If you experience any problems with the
installation or operation of your system,
contact Antunes Technical Service +1-
877-392-7854 (toll free).
Fill in the information in the next column
and have it handy when calling for
assistance. The serial number is on the
specication plate located on the system.
Purchased From
Date of Purchase
Model Number
Serial Number
Mfg. Number
Use only genuine Antunes replacement
parts in this unit. Use of replacement
parts other than those supplied by the
manufacturer will void the warranty.
IMPORTANT
Keep these instructions for future reference.
If the unit changes ownership, be sure this
manual accompanies the equipment.
Contents
General ..................................................2
Warranty Information ...........................2
Service/Technical Assistance.............2
Important Safety Information ..............3
Warnings ...............................................3
Specications .......................................4
Installation.............................................5
Installing the Release Sheet ................6
Bun Thickness Compression
Knob Settings.......................................6
Operating Instructions.........................7
Check Bun Thickness Compression
Settings ................................................7
Toasting Product ..................................7
If Product is Stuck Inside Toaster.........7
Adjusting Toast Quality.........................8
Shutting down the Toaster....................8
Factory Reset.......................................8
Hi Limit Reset Button ...........................8
Errors ...................................................8
Maintenance..........................................9
Daily Maintenance................................9
Weekly Maintenance..........................10
Monthly Cleaning ............................... 11
Quarterly Cleaning .............................13
Troubleshooting .................................15
Wiring Diagram ...................................16
Replacement Parts .............................18
Parts list ............................................18
Exploded Diagram 1...........................20
Exploded Diagram 2...........................21
Exploded Diagram 3...........................22
Exploded Diagram 4...........................23
Limited Warranty ................................24
IMPORTANT
Antunes reserves the right to change
specications and product design
without notice. Such revisions do not
entitle the buyer to corresponding
changes, improvements, additions or
replacements for previously pur-
chased equipment.

3
®
P/N 1011275 Rev. K 03/21
Important Safety
Information
Use the following guidelines for safe
operation of the unit.
yRead all instructions before
using equipment.
yFor your safety, the equipment is
furnished with a properly grounded
cord connector. Do not attempt to
defeat the grounded connector.
yInstall or locate the equipment only
for its intended use as described in
this manual. Do not use corrosive
chemicals in this equipment.
yDo not operate this equipment if
it has a damaged cord or plug, if
it is not working properly, or if it
has been damaged or dropped.
yThis equipment should be
serviced by qualied personnel
only. Contact Antunes Technical
Service for adjustment or repair.
yDo not block or cover any
openings on the unit.
yDo not immerse cord
or plug in water.
yKeep cord away from
heated surfaces.
yDo not allow cord to hang over
edge of table or counter.
yTurn the power o󰀨, unplug the
power cord, and allow unit to
cool down before performing any
service or maintenance on the unit.
yThe equipment should be
grounded according to local
electrical codes to prevent the
possibility of electrical shock. It
requires a grounded receptacle
with separate electrical lines,
protected by fuses or circuit
breaker of the proper rating.
yAll electrical connections
must be in accordance with
local electrical codes and any
other applicable codes.
yDo not clean this appliance
with a water jet.
Warnings
Be advised of the following warnings
when operating and performing
maintenance on this unit.
yIf the supply cord is damaged,
it must be replaced by the
manufacturer or its service agent
or a similarly qualied person
in order to avoid a hazard.
yDo not modify the power supply
cord plug. if it does not t the
outlet, have a proper outlet
installed by a qualied electrician.
yDo not use an extension
cord with this appliance.
yElectrical ground is required
on this appliance.
yCheck with a qualied electrician
if you are unsure if the appliance
is properly grounded.
yIf a chemical cleaner is used,
be sure it is safe to use on cast
aluminum. Observe all precautions
and warnings on product label.
yInspection, testing, and
repair of electrical equipment
should only be performed by
qualied service personnel.
yThis equipment is to be installed
to comply with the basic plumbing
code of the Building O󰀩cials
and Code Administrators, Inc.
(BOCA) and the Food Service
Sanitation Manual of the Food
and Drug Administration (FDA).
yDo not use abrasive materials. The
use of these may cause damage
to the stainless steel nish.
yChlorides or phosphates in
cleaning agents (e.g. bleach,
sanitizers, degreasers or
detergents) could cause
permanent damage to stainless
steel equipment. The damage is
usually in the form of discoloration,
dulling of metal surface nish,
pits, voids, holes, or cracks.
This damage is permanent and
not covered by warranty.
yThe following tips are
recommended for maintenance of
your stainless steel equipment:
yAlways use soft, damp cloth
for cleaning, rinse with clear
water and wipe dry. When
required, always rub in direction
of metal polish lines.
yRoutine cleaning should be
done daily with soap, ammonia
detergent, and water.
yStains and spots should be
sponged using a vinegar solution.
yFinger marks and smears
should be rubbed o󰀨
using soap and water.
yHard water spots should be
removed using a vinegar solution.

4
®
P/N 1011275 Rev. K 03/21
Model &
Mfg. No. Volts Watts Amps Hertz Plug Description
9210907
VCT-2
(Belt
Wraps)
120 1800 15 50/60
5-15P 15 Amps., 120
V., Non-Locking
(assembly only)
9210924
VCT-2
(Belt
Wraps &
w/ Knobs
Cover)
9210955
VCT-2
(No Belt
Wraps)
9210919
VCT-2
(Belt
Wraps)
25.5”
(647.7 mm)
13”
(330.2 mm)
10”
(254 mm)
Specications

5
®
P/N 1011275 Rev. K 03/21
Installation
NOTE: When placing the toaster into
service, make sure to provide
at least 3 inches of space on
all sides of the unit.
1. Remove unit and all packing
materials from shipping carton.
The toaster is shipped with an
accessories box that includes the
items listed below:
yBun Feeder Assembly
yBun Chute
yRelease Sheet (pkg. Of 2) A
Release sheet is also shipped
installed onto the unit platen.
yOwner’s Manual
NOTE: If any parts are missing
or damaged, contact
Antunes Customer Service
IMMEDIATELY at +1-877-392-
7856 (toll free).
2. Remove all packing materials and
protective coverings from the unit.
3. Refer to Figure 1. Wash, rinse, and
sanitize the Bun Feeder and Bun
Chute at the 3 compartment sink and
set aside to air dry.
NOTE: The removable parts have
CONTACT etched on them to
make it easier to identify which
toaster they belong to.
4. Refer to Figure 1. Remove the
Release Sheet.
NOTE: Do not wash the Release Sheet
in the sink. The Release Sheet
must be washed by hand.
5. Wipe all surfaces of the unit with a
hot damp cloth.
6. Wipe both sides of the Release
Sheet with a hot damp cloth.
NOTE: Do NOT use a dripping wet
cloth. Wring out before use.
7. Install the Bun Feeder and Bun
Chute onto the unit (Figure 1).
8. Refer to the section titled Installing
the Release Sheet on the next page.
Install the Release Sheet according
to those instructions.
NOTE: The main Control Panel is
located on the front of the
unit.
Figure 1. Components
Figure 2. Display
When placing the unit into service, pay
attention to the following guidelines.
yMake sure to provide at
least 3 inches of space on
all aides of the unit.
yMake sure the power switch is o󰀨
and the unit is at room temperature
before plugging in the power cord.
yDo not block or cover any
openings on the unit.
yDo not immerse the power
cord or plug in water.
yKeep the power cord away
from heated surfaces.
yDo not allow the power cord to
hang over edge of table or counter.
Bun Feeder
Release Sheet
(Appearance may vary
depending on model)
Bun Chute

6
®
P/N 1011275 Rev. K 03/21
Installing the Release Sheet
The Release Sheet allows buns to pass
through the toaster without sticking. The
toaster should never be operated without
a clean Release Sheet installed.
1. Fold and crease edges of the
Release Sheet as shown in Figure 4.
2. Fold and crease Release Sheet
in half at center point as shown in
Figure 5.
3. Turn unit on and Install Release
Sheet over Platen. The unit will feed
the Release Sheet into place.
Re-install Bun Feeder (Figure 6).
Bun Thickness Compression
Knob Settings
The toaster uses two Bun Thickness
Compression Knobs for proper toasting
of buns (heels and crowns)(Figure 3).
For best results, set both Bun Thickness
Compression Knobs to 4.
The compression settings range from 1
to 6. Setting 1 is the thinnest setting and
Setting 6 is the widest setting.
Bun
Feeder
Release
Sheet
Platen
Crease here
Fold down
Fold
UP
Fold
UP
1/2”
Figure 3. Bun Thickness Compression
Knobs
Figure 4. Fold and crease edges of
Release Sheet
Figure 5. Fold and crease Release Sheet
in half
Figure 6. Components
WARNING
Do NOT operate the toaster without
the release sheet installed. Do not use
any abrasive cleansers or tools such
as scrubbers or scrapers on the Platen.
Damage to the Platen from operation
without a Release Sheet or damage
caused from abrasive cleansers or
tools voids the warranty.

7
®
P/N 1011275 Rev. K 03/21
Operating
Instructions
NOTE: If the toasting quality needs
adjustment, refer to the section
titled “Adjusting Toasting
Quality” in the Operation
section of this manual.
1. Verify that the toaster is clean
and assembled correctly. Turn
the Power switch to the on
position. The unit makes a
clicking sound. This is normal.
2. The unit displays the software
version, the current platen
setpoint temperature and starts
to warm up.
3. After the system check, the unit
begins to warm up and Lo-P appears
on the display.
CROWNS
(Cut sides
facing IN)
HEELS
(Cut sides
facing IN)
Buns Exit
Toaster Here
If Product is Stuck Inside
Toaster
If buns or a bread slice gets stuck
inside the toaster, use the platen tool to
dislodge it from the toaster. Before using
the platen tool:
1. Insert one edge of a new scrub pad
onto the top slot of the platen tool.
2. Insert the other edge of the scrub
pad into the bottom slot. Make sure
the scrub pad is at against the tool.
3. From the top of the toaster, insert
the platen tool with the pad facing
the middle of the toaster. Dislodge
product.
4. The unit displays the USE
message when it reaches proper
operating temperature (in
approximately 10 minutes).
Check Bun Thickness
Compression Settings
Before toasting product, verify that the
Bun Thickness Compression Knobs are
set appropriately. The typical settings for
crowns and heels is #4, however these
can be changed according to product
thickness. See the section titled “Bun
Thickness Compression Knob Settings”
for more information.
Toasting Product
Test the toaster before use by toasting
1 bun and 1 slice of Wheatberry bread.
Facing the front of the unit, insert product
as described:
yBun - Feed crown into front slot
and heel into back slot, with
cut sides facing each other.
yWheatberry bread - place 1
slice of bread into back slot.
Check the color against Quality Photos
(Buttered White Bun Toasting, Multi grain
Bun Toasting, Chicken Salad Sandwich
toasting). Adjust settings if needed.
Figure 7. Toasting
Lo-P
Power
Switch.
USE
WARNING
Do NOT use the platen tool without a
scrub pad installed. Be sure to insert
the platen tool into the toaster with the
scrub pad facing the toaster platen. Do
not allow the metal portion of the platen
tool to contact the toaster platen.

8
®
P/N 1011275 Rev. K 03/21
Adjusting Toast Quality
The unit can be adjusted to provide a
lighter or more darkly toasted product.
The lightest setting is 1 and the darkest
setting is 10.
To view the current Light/Dark setting,
briey press Light or Dark button. The
current Light/Dark setting appears in the
display.
To change the Light/Dark setting, press
and hold the Light or Dark button
until the unit beeps. Press the Light or
Dark button set the Light/Dark value as
desired.
D 4
Release the Button. The USE message
ashes in the display as the unit adjusts
the platen temperature accordingly.
USE
When the toaster reaches the newly
set Light/Dark temperature, the USE
message stops ashing and remains on.
The toaster is ready for use.
USE
NOTE: The Light/Dark value is
maintained when the unit is
powered o󰀨.
Hi-Limit Cap
Hi Limit Reset Button
A hi-limit control turns o󰀨 power to the
unit if it overheats. To reset this Hi-Limit
control, allow su󰀩cient time (10-15 min-
utes) for the unit to cool down, then re-
move the Hi-Limit control cap and press
the reset button located on the rear of
the unit (Figure 8). If the unit requires
continuous resetting, call for service.
Errors
The toaster displays any kind of error
message, contact the factory immediately
at 1-630-784-1000
Shutting down the Toaster
To turn the toaster o󰀨, turn the Power
switch to the o󰀨 position.
Factory Reset
Follow these steps to reset the toaster to
the factory settings
1. Turn the toaster o󰀨.
2. Press and hold both the Light and
Dark buttons and turn the toaster on.
3. Continue holding the Light and Dark
buttons until “fr” (factory reset)
appears in the display. The toaster
beeps when resetting is done and
starts up normally.
Figure 8. Hi-Limit Reset Button

9
®
P/N 1011275 Rev. K 03/21
Maintenance
Daily Maintenance
NOTE: The following are general
maintenance procedures. For
additional details including
approved chemicals, please
see the Toaster Procedure
documents by scanning the
QR Code on the front page of
this manual.
The daily maintenance steps involve:
yCleaning the Accessories
and Toaster
yCleaning the Release Sheet
Cleaning the Accessories and Toaster
1. Turn the toaster o󰀨 and allow it to
cool before proceeding.
2. Remove the Bun Feeder, Release
Sheet, and Bun Chute and set aside
(Figure 9).
NOTE: Do not wash the Release Sheet
in the sink. It must be washed
by hand.
3. Wash the Bun Feeder and Bun
Chute in soap and water. Rinse with
clean water and allow to air dry.
4. Wipe all surfaces of the unit with a
hot damp cloth.
NOTE: Do not use a dripping wet
cloth. Wring out before use.
Cleaning the Release Sheet
1. Inspect the Release Sheet. Replace
the Release Sheet if it is worn,
creased, or torn.
2. Spray an approved cleanser on a
clean, dry towel.
3. Wipe the Release Sheet rmly from
top to bottom.
4. Repeat this procedure with a clean,
dry towel dampened with water.
5. Next, wipe the release sheet with
a clean towel dampened with an
approved sanitizer. Allow to air dry.
6. Repeat Steps 1 through 6 on the
inside portion of the Release Sheet.
Set the clean Release Sheet aside.
Cleaning the Belt Wraps
1. Open the front and rear Conveyor
Covers (Figure 10)
2. Inspect the front and rear Belt
Wraps. Replace the Belt Wraps
if there are any signs of tearing,
folding, or other damage.
3. Turn on the unit.
NOTE: This step requires that the
toaster be turned on with the
Conveyor Covers open. Use
caution during these steps.
4. Spray a clean, sanitized towel with
an approved cleanser and wipe the
front and rear Belt Wraps for one full
rotation.
5. Repeat Step 4 with an approved
sanitizer.
NOTE: Repeat these steps as needed
until the Belt Wraps are clean
and tacky/sticky to the touch.
6. Reinstall the Release Sheet, Bun
Chute, and Bun Feeder and return
the toaster to operation.
Cleaning the Rear Fan
Use a clean dry cloth and wipe the fan
intake. If there is heavy debris buildup,
use an Ecolab Detail Brush (item#
92212765) followed by a clean, dry cloth
(see Figure 11).
Figure 9. Remove Bun Feeder, Release
Sheet, and Bun Chute
Figure 10. Open front and rear Conveyor
Covers
Figure 11. Cleaning Rear Fan
WARNING
The unit will remain hot while it is
cooling down. Personal injury and
burns may result from touching the unit
before it is nished cooling down. Wear
Heat Resistant Gloves.

10
®
P/N 1011275 Rev. K 03/21
Weekly Maintenance
The following weekly maintenance is
recommended only when buttering buns
prior to toasting them:
Butter buildup on the platen will have a
negative a󰀨ect on toast quality. Follow
the procedure below to clean the platen.
1. Turn the unit o󰀨, unplug the power
cor,d and allow the unit to cool down
for 15 minutes.
2. Put on heat resistant gloves.
Remove the Bun Feeder, Release
Sheet, and Bun Chute (Figure 6).
Set these item aside.
3. Set both Bun thickness Compression
Knobs to 6. (Figure 7).
4. Place a red food tray in front of
toaster to collect drips from cleaning.
5. Inspect scrub pad to ensure it is
clean and undamaged. Discard
scrub pad if it has loose shreds, food
particles or debris stuck in bers.
6. Insert one edge of scrub pad into top
slot.
7. Insert other edge into bottom slot,
making sure pad is at.
8. Prepare clean rinse water. It is
helpful to have water in a 12 qt
container next to toaster during
cleaning process.
9. Spray Sizzle onto scrub pad.
10. Scrub each side of toasting platen
gently with scrub pad, applying
additional Sizzle to scrub pad as
needed (Figure 12)
NOTE: Front and rear covers of
toaster should be closed
during this step to prevent
Sizzle from dripping on the belt
wraps or other areas of toaster.
11. Rinse scrub pad in clean water.
12. Press against scrub pad with gloved
hand, while it is in water, to rinse it
out.
13. Squeeze out excess water by
scraping scrub pad against edge of
container.
NOTE: It is important to squeeze
out excess water because
too much water dripping into
toaster can damage electronic
components.
14. Scrub each side of toasting platen
gently with rinsed scrub pad to
remove Sizzle residue. Continue
rinsing scrub pad and scrubbing
platen gently until all residue has
been removed from platen.
NOTE: It will be necessary scrub
each side of toasting platen
with rinsed scrub pad
approximately 4-5 times to
remove all Sizzle residue.
15. Discard scrub pad. Scrub pads are
for single use only.
16. Remove bun chute and red food tray
and take them to compartment sink
for cleaning.
17. Complete remaining steps in daily
cleaning process. (See Contact
Toaster: Cleaning Contact Toaster at
End of Day.)
PLATEN
CLEANING
TOOL
NOTE: Platen cleaning tool and
scrub pad are sold separately
(kit: 7001126)
SCRUB
PAD
PLATEN
Figure 12. Using Platen Cleaning
Tool

11
®
P/N 1011275 Rev. K 03/21
4. Remove both Belt wraps if present-
lift the ap on the Belt Wrap and
disconnect the Belt Wrap Hooks
from the Conveyor Chain (Figure
15). Remove the Belt Wraps from
the toaster.
5. Inspect the Belt Wraps (if present)
for rips or tears. If the Belt Wraps are
in good condition, set them aside.
They will be reinstalled onto the
toaster later in this process.
Monthly Cleaning
The monthly preventative maintenance
steps include:
yCleaning the Conveyor Belt
Chains
yChecking the Conveyor Belt
Chains for Stretching
Cleaning the Conveyor Belt Chains
1. Turn the unit o󰀨, unplug the power
cord, and allow the unit to cool down.
2. Put on heat resistant gloves.
Remove the Bun Feeder, Release
Sheet, and Bun Chute (Figure 13).
Set these item aside.
3. Set both Bun thickness Compression
Knobs to 6. Next, open both
Conveyor Covers (Figure 14).
Figure 13. Remove Bun Feeder, Release
Sheet, and Bun Chute
Figure 14. Open front and rear Conveyor
Covers
Figure 15. Belt Wrap Hooks
Figure 16. Remove Belt Wrap Hooks
Bun
Feeder
Release
Sheet
Bun
Chute
6. Use a clean, nylon brush to remove
all debris and residue from the
Conveyor Belt Chains. Do this on
both sides of the toaster.
7. Clean and sanitize the front and
rear Conveyor Belt Chain with a
green scrub pad sprayed with Super
contact Cleaner solution. Wipe the
links of the Conveyor Belt Chain
rmly from side to side until they are
completely free of residue and debris
(Figure 9). Wipe the Chains with a
clean sanitizer soaked towel.
8. Plug in the power cord and turn the
unit on. Wait for both Conveyor Belt
Chains to rotate and expose the
uncleaned portion of the chains. Turn
the unit o󰀨 and unplug the power
cord again. Repeat Steps 6 and 7 to
clean and sanitize the soiled side of
the Conveyor Chains.
NOTE: You may need to repeat steps
7 and 8 to ensure the Conveyor
Belt Chains are completely free
of debris and cleanser.

12
®
P/N 1011275 Rev. K 03/21
Checking the Conveyor Belt Chains
Tension
1. Set the Bun Thickness Compression
Knobs to 6 and 6 and ensure both
Belt Wraps are removed.
2. Locate the approximate center-point
of the Conveyor Belt Chain.
3. Pull the Conveyor Belt Chain away
from the edge of the toaster (Figure
17).
4. Using a U.S. Dime coin (1.8 cm) for
reference or a ruler, measure the
space between the toaster frame
and the Conveyor Belt Chain (Figure
17). The coin should t snugly.
5. If the gap is more than twice
the width of the coin (2.6 cm),
disconnect the Conveyor Belt chain
by squeezing any two links together
and unhooking both ends of the one
link (Figure 18). Pliers may be used.
NOTE: There are two small 1/2 inch
links on each side of the
Conveyor Belt Chain. The rest
are large 3/4 inch links.
NOTE: Depending on how loose the
chain is, remove a 1/2” or 2/4”
link.
NOTE: It is recommended to perform
the Quarterly Cleaning any
time you disconnect or remove
a Conveyor Belt Chain from
the toaster.
6. Reassemble the Conveyor Belt
Chain onto the sprockets.
NOTE: Make sure the Conveyor Belt
Chain hooks are pointing
DOWN as shown in Figure 10.
7. Measure the gap again to conrm
the gap is approximately the width of
the U.S. Dime coin.
NOTE: If the Conveyor Belt Chain is
too tight, remove a small 1/2
inch link and install a large
3/4 inch link in its place. This
decreases the length of the
Conveyor Belt Chain by 1/4
inch overall.
8. Repeat steps 1 through 6 on the
opposite Conveyor Belt Chain.
Reassembling the Toaster
1. Reinstall the Belt Wraps onto the
toaster under the support rods and
making sure the ap is pointing
down.
2. Connect the Belt Wrap hooks to the
Conveyor Belt Chain (Figure 19)
NOTE: Make sure the Belt Wraps are
installed under the yellow
rods.
3. Close the Conveyor Covers.
4. Reinstall the Release Sheet, Bun
Chute, and Bun Feeder and return
the toaster to operation.
Figure 17. Measure Conveyor Belt
Tension
Figure 18. Disconnect Conveyor Belt
chain
Figure 19. Connect Belt Wrap Hooks

13
®
P/N 1011275 Rev. K 03/21
Quarterly Cleaning
The Quarterly Cleaning involves cleaning
the interior of the unit.
1. Turn the unit o󰀨, unplug the power
cord and allow the unit to cool down.
2. Put on heat resistant gloves.
Remove the Bun Feeder, Release
Sheet, and Bun Chute (Figure 9).
Set these item aside.
3. Set both Bun thickness Compression
Knobs to 6. Next, open both
Conveyor Covers (Figure 14).
4. Remove both Belt wraps if present-
lift the ap on the Belt Wrap and
disconnect the Belt Wrap Hooks
from the Conveyor Chain (Figure
15). Remove the Belt Wraps from
the toaster.
5. Inspect the Belt Wraps (if present)
for rips or tears. If the Belt Wraps are
in good condition, set them aside.
They will be reinstalled onto the
toaster later in this process.
6. Disconnect the Conveyor Belt chains
by squeezing any two links together
and unhooking both ends of the one
link (Figure 20). Pliers may be used.
Remove the Conveyor Belt Chains
and set aside.
7. Use a clean, nylon brush to carefully
remove all debris and residue from
the inside components of the toaster
(Figure 21). Do this on both sides of
the toaster.
NOTE: With proper and regular daily
and monthly cleaning, the
interior of toaster should be
free of residue and debris. If
you nd that the interior is
extremely dirty on a regular
basis, please review how
the daily and monthly the
frequency and daily and
monthly cleaning steps.
8. Reassemble the Conveyor Belt
Chain onto the sprockets.
NOTE: Make sure the Conveyor Belt
Chain hooks are pointing
DOWN as shown in Figure 20.
9. For Mfg. No. 9210907, reinstall the
Belt Wraps onto the toaster under
the yellow rods and making sure the
ap is pointing down.
10. Connect the Belt Wrap clips to the
Conveyor Belt Chain.
Figure 20. Disconnect Conveyor Belt Chains
Figure 21. Clean the inside components
NOTE: Make sure the Belt Wraps are
installed under the support
rods.
11. Close the Conveyor Covers.
12. Reinstall the Release Sheet, Bun
Chute, and Bun Feeder and return
the toaster to operation.
USE A CLEAN, NYLON BRUSH
(SIMILAR TO THE IMAGE BELOW) TO
CAREFULLY REMOVE ALL DEBRIS
AND RESIDUE FROM THE INSIDE
OF THE TOASTER.
DO THIS ON BOTH SIDES OF THE
TOASTER.

14
®
P/N 1011275 Rev. K 03/21
Replacing the Belt Wraps (Mfg. No.
9210907 Only)
The frequency of Belt Wrap replacement
depends on usage and daily mainte-
nance. We recommend replacing Belt
Wraps Quarterly for optimal performance.
NOTE: Belt Wraps should feel sticky/
tacky not slick/slippery.
1. Turn the unit o󰀨, unplug the power
cord, and allow the unit to cool down.
2. Put on heat resistant gloves.
Remove the Bun Feeder and Bun
Chute (Figure 22). Set these item
aside.
3. Set the Bun Thickness Compression
Knobs to 6 and 6.
4. Next, open both Conveyor Covers
(Figure 23).
5. Remove both existing Belt Wraps.
Lift the ap on the Belt Wrap and
disconnect the Belt Wrap hooks from
the Conveyor Belt Chain. Discard
used Belt Wraps.
6. Install the new Belt Wraps onto the
toaster under the support rods and
making sure the ap is pointing
down.
7. Attach the Belt Wrap hooks to the
Conveyor Chain.
NOTE: Verify both hooks are attached
by pulling belt wrap away from
chain and reattach if needed.
8. Close the Conveyor Covers.
9. Reinstall the Bun Chute and Bun
Feeder and return the toaster to
operation.
Figure 22. Bun Feeder and Bun Chute
Bun Feeder
Bun
Chute
Figure 23. Open Conveyor Covers
Figure 24. Belt Wrap Hooks Figure 25. Rear Fan
Cleaning the Rear Fan
1. Turn the unit o󰀨, unplug the power
cord, and allow the unit to cool for 15
minutes before proceeding.
2. Refer to Figure 25. Remove the four
Rear Panel screws circled and set
aside.
3. Carefully remove the Rear Panel and
lay it down so the fan is accessible.
4. Wipe inner surface of the Rear Panel
and rear compartment with a clean,
dry cloth to remove all debris and
residue.
5. Use a clean, dry towel or a clean,
nylon brush to remove all debris and
residue from the Fan.
6. Reattach the Rear Panel and secure
with the screws removed in Step 2.
Fan

15
®
P/N 1011275 Rev. K 03/21
Troubleshooting
Problem Possible Cause Corrective Action
No Control Display
Power cord not plugged in Plug power cord into the proper electrical outlet.
Circuit breakers turned o󰀨 or tripped. Damaged elec-
trical outlet, plug, or cord. Power switch damaged
Reset circuit breakers. If they trip again, check the power cord,plug, and
outlet for damage. Contact Antunes technical service, your maintenance
person, or authorized service provider.
Power Switch not turned on or is faulty. Turn the unit o󰀨 and then on again. If the problem persists, Contact Antunes
technical service, your maintenance person, or authorized service provider.
Faulty Transformer
Conveyor does not rotate
Conveyor Belt/Chain has stretched. Chain skipping
on sprockets.
Measure and adjust the conveyor belt chains as described in the Mainte-
nance section of this manual.
Loose setscrew on one of the drive sprockets Contact Antunes technical service, your maintenance person or authorized
service provider.
Motor Drive Chain loose Contact Antunes technical service, your maintenance person or authorized
service provider.
Internal part /object interfering within conveyor
system Check for interference & clear up as necessary.
Conveyor(s) skips or hesitates
Conveyor chains loose. Measure and adjust the conveyor belt chains as described in the Mainte-
nance section of this manual.
Belt wrap clip not attached. Verify both clips on each belt wrap are attached, reattach if necessary.
Loose or misaligned sprocket Contact Antunes technical service, your maintenance person or authorized
service provider.
Motor drive chain loose or stretched Contact Antunes technical service, your maintenance person or authorized
service provider.
Drive motor(s) have failed Contact Antunes technical service, your maintenance person or authorized
service provider.
Buns not toasting adequately
Compression settings are incorrect. Use recommended setting or adjust compression knobs as needed to
achieve desired toast quality.
Release sheet is worn or needs cleaning (replace
every 2-4 weeks).
Inspect release sheet for cleanliness, worn spots, wrinkles , or tears. Clean
or replace release sheet as described in the Maintenance section of this
manual.
Platen has butter/debris buildup. Clean Platen as described in the Maintenance section of this manual.
Light/Dark setting needs to be adjusted. Adjust light/dark setting. See Operation section of this manual.
Crowns and/or Heels must be
forced into the toaster. Buns
sticking and burning.
Belt wraps are dirty, worn or damaged. Clean or replace Belt Wraps as described in the Maintenance section of this
manual.
Platen has butter/debris buildup. Clean Platen as described in the Maintenance section of this manual.
Release sheet is dirty, worn or damaged. Clean both sides or replace release sheet as described in the Maintenance
section of this manual.
Conveyor Chains loose. Adjust the conveyor belt chains as described in the Maintenance section of
this manual.
Drive motor stalls intermittently. Contact your Maintenance person or Authorized Service agency for service.
Compression settings are incorrect. Use the recommended settings or adjust as needed to achieve desired toast
quality.
Buns are not inserted into the toaster properly. Insert Crowns in front conveyor with and Heels in rear conveyor. Cut side of
buns need to face the platen.
Toaster making unusual
sounds
Fan needs to be cleaned or replaced. Clean fan as described in the Maintenance section of this manual or contact
your maintenance person or authorized service company.
Conveyor belt chains have stretched or adjusted
incorrectly.
Adjust the conveyor belt chains as described in the Maintenance section of
this manual.
Motor Drive chain needs lubrication. Lubricate chain.
Conveyor shaft bearing is binding. Contact your Maintenance person or Authorized Service agency for service.
Buns getting caught in bun
chute area Bun chute installed incorrectly Reinstall Bun chute correctly.
Toaster displays ERR 10. Internal temperature of control compartment ex-
ceeded 160° F.
Verify fan intake on back of toaster is clean, not blocked and has proper
spacing. Clean cooling fan if needed, if not rotting, contact your authorized
service provider. Check if cooling fan is functioning. If not, replace fan.
Toaster Displays ERR 11,
12,15 or 17. Electrical failure.
Perform a factory reset. Ensure power switch is in o󰀨 position and press and
hold Up & Down arrow buttons together while turning power switch on. Dis-
play will show FR (factory reset). If Error code continues to display, contact
Antunes technical service.

16
®
P/N 1011275 Rev. K 03/21
Wiring Diagram

17
®
P/N 1011275 Rev. K 03/21
Terminal
Block #2
Terminal
Block #3
Terminal
Block #1
Transformer
Power
Switch
Hex Nut
For mounting
Relay Board
Hex Nut
For mounting
Relay Board
RELAY BOARD

18
®
P/N 1011275 Rev. K 03/21
Replacement Parts
Parts list
(See Exploded diagram)
Note
Use only genuine Antunes replacement parts in this unit.
Use of parts other than those supplied by the manufacturer
will void the warranty.
Item
No. Part # Description Qty.
10014048 Inner Spring Tensioner Assy. 4
20012982 Conveyor Belt Assembly 37/2 2
30012988 Tensioner Assembly 4
4 0012989 Bun Feeder Assembly 1
60021900 Idle Bearing Retainer Weldment (Incl.
with kit 700115 - Item 100) 1
70021959 Cam Weldment 2
80021960 Base Weldment 1
9 0021962 Control Panel Weldment 2
10 0021964 End Housing Weldment 1
11 0021965 Control Housing Weldment 1
12 0022040 Bun Chute Weldment 1
13 7000780 Platen, Grill 120V/1800W 1
14 0400147 Bushing, Shorty 7/8” 1
15 0400265 Bushing, Shorty 3/8” 4
16 0400437 Strain Relief, Rt Angle 1
17 0500464 Bearing Retainer 1
18 0503495 Bracket, Retainer Right 2
19 0503496 Bracket, Tensioner-Right 2
20 0503497 Bracket, Tensioner-Left 2
21 0503507 Bracket, Retainer Left 2
22 0506755 Retainer, Bearing 6
23 0508503 Plate, Motor 1
24 0508370 Panel, Electrical 1
25 0507180 Bracket, Trx-Hi-Limit 1
26 0700936 Power Cord Right Angle 1
27 0800455 Rod, Knob (Heel) 1
28 0800457 Rod, Knob (Crown) 1
29 0800458 Rod, Support 4
30 0800460 Shaft, Drive 2
31 0800461 Shaft, Idler 2
32 1000900 Label - Warning 1
33 1001181 Label, Crown 2
35 1001550 Label, Control 1
36 1001551 Label, Install 1
37 1001552 Label, Cam (Heel) 1
38 1001553 Label, Cam (Crown) 1
39 1001556 Label, Wiring Diagram 1
40 1001592 Label, Chain Tensioning 1
Item
No. Part # Description Qty.
41 1031188 Spec Label 2
42 2100230 Bumper, Recess W/Washer 4
43 2100348 Knob, 1/4” Shaft, Push-On 2
44 2110127 Ring, Retaining 8
45 2120107 Spacer, Aluminum 2
46 2120147 Spacer, Leg 4
47 7000296 Ball Bearing Kit (2-Pak) 1
48 2150173 Sprocket, 25B12 3/8” Bore 1
49 2150179 Sprocket, 25B14 1/2” Bore (1 Incl. with
kit 700115- Item 100) 3
50 7000224 Bearing & Retainer Kit 1
51 7000207 Sprocket Kit, 25B28 x 1/2” Bore
Stepped Tooth 1
52 2150258 Bearing, Idler (Incl. with kit 700115 -
Item 100) 1
53 2150260 Spacer, Bearing 6
54 2150368 Miter Gear, 20° Pressure Angle 4
55 2150370 Chain, Drive 1
56 2180145 Cover, Bumper 4
57 3000124 Ring, Retaining 3/8” (Incl. with kit
700115 - Item 100) 1
58 304P105* Nut, Hex ‘Keps’ #4-40 2
59 306P121* Screw, Mach #6-32 X 3/4” 2
60 306P123* Screw, Mach #6-32 X 7/8” Slrndhd 4
61 306P130* Nut, Hex Keps #6-32 (Small Pattern) 8
62 306P156* Screw, Mach. #6-32 X 1/2” 2
63 308P115* Screw, Mach. #8-32 X 3/8” 8
64 308P143* Nut, Hex ‘Keps’ #8-32 8
65 308P144* Screw, #8-32 X 1/4” (#6 Head) 16
66 308P157* Screw, Tap 8-32 X 3/8”Lg 4
67 308P203* Screw, Tap 8-32 X 3/8” W/Int. Tooth
Washer 26
68 310P103* Screw, Mach. #10-32 X 1/4” 4
69 310P136* Screw, Mach. #10-32 X 1/4” 4
70 310P146* Nut, Hex ‘Keps’ #10-32 24
71 310P213* Screw, Phpnhd #10-16 X 3/4” Thrd
Form 4
72 325P104* Washer, Flat 1/4” S/S 4
73 325P163* Set Screw, 1/4-28 X 5/16” 8
74 325P203* Washer, Spring Steel Single-Wave 8
75 3380116 Screw, 3/8-16 X 3/8 W/ 1/2 Shoulder 4
76 7001375 Drive Motor Kit 120V 1
77 4000210 Fan, Axial 115V 1
78 4010199 Transformer, 120 Vac/12Vac 1
79 7000882 Power Switch Repl. Kit 1
80 4030332 Thermostat, Hi-Limit 1

19
®
P/N 1011275 Rev. K 03/21
NOTE: If your unit currently has the older styled roller
tensioners attached to the covers of the unit,
it is highly RECOMMENDED to eliminate the
roller tensioner and upgrade to the newer Inner
Tensioners.
#106 - P/N 7001932
NOTE: If a new cover is ordered it will NOT include the
roller tensioners formerly attached to the inside
of the covers. You will need to order the new inner
tensioners to maintain proper tension of the toaster
belts.
#106 - P/N 7001932
Replacement Parts
Parts list Continued
Item
No. Part # Description Qty.
81 4050214 Thermocouple Type “K” (Open End) 1
82 4051010 Relay, Random Phase, Solid State-50A 1
83 4060234 Wire Strap - 3/7” 1
84 4060303 Bus Bar Contact 3-Pole 2
85 4060355 Terminal Block, 3-Pole 3
86 7001005 Control Board Kit 1
4070392 Control Board (9210919 ONLY) 1
87 4070213 Varistor Board 1
88 7002037 Black Wavy Silicone Belt 1
89 0021961 Conveyor Cover Weldment 2
90 0024485 Conveyor Cover Weldment w/ Knobs
(9210924 ONLY) 1
93 7001600 Rail, Slide Kit 4
94 0509539 Spring, Inner Tensioner 4
95 2100393 Bottom Rail, Slide 1
96 2100378 Rail, Slide 1
97 3020106 Rivet, Semi Tubular-3/16” 2
98
7000989 Sheet, Platen (Pk of 2) 1
7001168 Sheet, Platen (3 Pk - 9210919 ONLY) -
7001169 Sheet, Platen (10 Pk - 9210919 ONLY) -
99 7001126 Cleaning Tool Kit VCT-2 (9210919
ONLY) 1
100 7001115 Idler Sprocket Replacement Kit 1
101 7001372 Relay Board Kit 1
102 7001602 Ba󰀪e Kit 1
103 7001529 Drive Chain Tensionser 1
104 0600155 Compression Setting Spring 1
105 7001126 Platen Cleaning Kit (see pg 10) (Clean-
ing Tool is NOT Included) -
106 7001932 Inner Tensioner Kit (2 pack) 2
107 0600179 Extension Spring (Mfg. No. 9210907 &
9210955 ONLY) 4
*Available in Packages of 10 (ten).

20
®
P/N 1011275 Rev. K 03/21
Replacement Parts
Exploded Diagram 1
26
86
53
51
53
51
22
70
60
63
62
82
85
85
87
75
54
54
44
74
14
79
38
28
43
35
27
37
43
12
4
67
9
65
15
81
65
62
16
101
99
Cleaing Tool is
NOT included.