Antunes Gold Standard Toaster GST-2H User manual

P/N 11012011 Rev. C 06/18
Gold Standard Toaster
owner’s manual
Model GST-2H Int’l
Manufacturing Numbers:
9210961 & 9210962
www.antunes.com

2P/N 1012011 Rev. C 06/18
Overview
The Antunes Gold Standard Toast-
er is an energy-e󰀩cient toaster
designed with a dual belt feed
for toasting crowns, heels, and
clubs. The electronic temperature
controller ensures proper calibra-
tion and event toasting. A continu-
ously moving dual belt allows for
immediate feeding of buns with-
out sticking. The Gold Standard
Toaster features a new design that
saves valuable counter space and
increases energy e󰀩ciency.
Before Use
This manual contains safety,
installation, and operating proce-
dures for the toaster. Read and
understand it completely before
installing or operating the toaster.
Keep this document for reference.
If the toaster changes ownership,
this manual must accompany it.
In Case of Damage
If the toaster arrives damaged, le
a claim with the carrier immedi-
ately. Save all packing materials
when ling a claim. Freight dam-
age claims are the responsibility of
the purchaser and are not covered
under warranty.
Website
www.antunes.com
Service/Technical
Assistance
If any parts are missing or dam-
aged, contact Antunes Customer
Service immediately at +1-877-
392-7856 (toll free).
If there are problems with the
installation or operation of this
product, contact Antunes Technical
Service toll free at +1-877-392-
7854.
Fill in the information in the next
column and have it handy when
calling for assistance. The serial
number is on the specication plate
located on the system.
Equipment Information to Save
Purchased from:
Date of purchase:
Model number:
Serial number:
Manufacturing number:
Authorized Service Agency
Name:
Phone No:
Address:
Contents
Overview 2
Before Use 2
In Case of Damage 2
Service/Technical Assistance 2
Equipment Information to Save 2
Authorized Service Agency 2
Safety Information 3
Installation 3
Operation 3
Maintenance 3
Service 3
Specications 4
Installation 5
Operation 5
Light/Dark Adjustments 5
User Mode 6
Error Codes 6
Manager Mode 6
Safety Features 6
Hi-Limit Control 6
Purging Buns from Toaster 6
Fault Messages 6
Daily Cleaning 7
Clean Toaster & Belt Wraps 7
Inspect the belts 7
Quarterly Cleaning 8
Remove Wraps & Clean Rollers 8
Install Belt Wraps 8
Annual Cleaning 9
Clean Cooling Fans and Electrical
Housings 9
Troubleshooting 10
Replacement Parts 12
Wiring Diagram 16
Mfg No. 9210961 16
Mfg No. 9210962 17
Notes 18
Limited Warranty 19

3
P/N 1012011 Rev. C 06/18
Safety Information
Installation
yRead and understand all
instructions before installing or
using the eated display cabinetr
yInstall and locate the equipment
only for its intended use as
described in this manual.
yAll electrical connections
must be in accordance with
local electrical codes and any
other applicable codes. The
equipment must be grounded
according to local electrical
codes to prevent electrical
shocks. It requires a grounded
receptacle with separate electrical
lines, protected by fuses or a
properly-rated circuit breaker.
yElectrical ground is required
on this appliance. Consult a
qualied electrician if there is any
uncertainty about whether the
appliance is properly grounded.
yDo not modify the power supply
cord plug. If it does not t the
outlet, have a proper outlet
installed by a qualied electrician.
yDo not use an extension
cord with this appliance.
Operation
yThe toaster is furnished with
a properly grounded cord
connector. Do not attempt to
defeat the grounded connector.
yDo not operate the toaster if it
has been damaged or dropped,
if it has a damaged cord or plug,
or if it is not working properly.
yDo not block or cover any
openings on the equipment.
yDo not immerse the cord
or plug in water.
yKeep the cord away from
heated surfaces.
yDo not allow the cord to
hang over the edge of
a table or counter.
Maintenance
yDo not use abrasive materials;
they can damage the toaster’s
stainless steel nish.
yDo not use corrosive
chemicals in this equipment.
yChlorides or phosphates in
cleaning agents (e.g., bleach,
sanitizers, degreasers, and
detergents) can permanently
damage stainless steel
equipment. The damage
is usually in the form of
discoloration, dulling of the
metal surface nish, pits,
voids, holes, or cracks. This
damage is permanent and is
not covered by warranty.
yUse only chemical cleaners
that are safe for cast aluminum.
Observe all precautions and
warnings on product labels.
yAlways use a soft, damp cloth
for cleaning. Rinse with clear
water and wipe dry. When
required, always rub in the
direction of metal polish lines.
yRoutine cleaning should be
performed daily with soap,
ammonia detergent, and water.
ySponge stains and hard
water spots with a 50%
vinegar solution.
yRub o󰀨 nger marks and
smears using soap and water.
yDo not clean the toaster
with a water jet.
Service
yInspection, testing, and
repair of electrical equipment
must be performed only by
qualied service personnel.
yHave the toaster serviced only
by qualied personnel. Contact
Antunes Technical Service
for adjustment or repair.
yTurn the power o󰀨, unplug the
power cord, and allow unit
to cool to room temperature
before performing any
service or maintenance.
yIf the supply cord is damaged,
it must be replaced by the
manufacturer, its service agent,
or a similarly qualied person in
order to avoid an electrical hazard.

4P/N 1012011 Rev. C 06/18
Specications
Model &
Mfg. No. Volts Watts Hertz Plug Description
GST-2H
9210961 230 2000 50/60
CEE 7/7,
16 Amp., 250 VAC
(Assembly Only).
GST-2H
9210962 208 2000 60
NEMA 6-20P
20 Amp, 250 Volt
Right Angle
A B
C
Model &
Mfg. No.
Width
(A)
Depth
(B)
Height
(C)
GST-2H
9210961 22" (559 mm) 21" (533 mm) 17” (432 mm)
GST-2H
9210962 22" (559 mm) 21" (533 mm) 17” (432 mm)

5
P/N 1012011 Rev. C 06/18
Installation
1. Remove unit and all packing
materials from shipping carton.
2. Open the Accessories Box. It
should contain the following:
yBun Chute
yBun Feeder
y1 Belt Set
yOwner’s Manual
NOTICE: If any parts are missing or
damaged, contact Antunes
Customer Service IMMEDI-
ATELY at [phone]
(toll free).
3. Open the side door (Figure 1)
and remove all of the plastic ties
securing the toaster mechanism.
4. Remove all packing materials and
protective coverings from the unit.
5. Wipe the entire exterior of the
toaster and the accessories
mentioned above with a hot damp
cloth. Allow to air dry
NOTICE: Do NOT use a dripping
wet cloth. Wring out before
use.
6. Attach the Bun Chute, Bun Feed-
er, and Butter Wheel assembly.
7. Make sure the Compression Knob
is set to 3, the default setting.
When placing the toaster into service, pay
attention to the following guidelines.
yThe power cord is located
at the bottom of the unit.
The unit is designed to be
placed on a table that will
NOT pinch the power cord.
yMake sure the power switch is o󰀨
and the unit is at room temperature
before plugging in the power cord.
yDo not block or cover any
openings on the unit.
yDo not immerse the power
cord or plug in water.
yKeep the power cord away
from heated surfaces.
yDo not allow the power cord to hang
over edge of table or counter.
yPlace the unit on a sturdy, level
table or other work surface.
yTurn the power switch to
o󰀨 (if it is set to on).
yEnsure the line voltage
corresponds to the stated voltage
on the specication label and
power cord warning tag.
8. Plug the power cord into the ap-
propriate power outlet. Refer to the
specication plate for the proper
voltage.
Figure 1. Gold Standard Toaster - 2H
Operation
1. Press and release the Power
button to turn the toaster on. Al-
low the toaster to warm up until
USE appears in the display
2. Set the Compression Knobs to
the desired setting. The recom-
mended Compression Settings
are:
CROWN-#4HEEL-#3
3. Insert product into the appro-
priate lane on the Bun Feeder
according to Bun Feeder labels.
Insert buns with the cut side fac-
ing down.
4. Finished product drops into the
bun landing zone.
Light/Dark Adjustments
The light/dark value can be adjusted
when the unit is displaying “USE”.
1. To adjust the light/dark value,
press the LIGHTER or DARK-
ER button. The display will
change to show the current
light/dark value.
NOTICE: The default light/dark
value is d0.
2. Press the LIGHTER or DARK-
ER buttons to change the light/
dark value. The adjustment
range is L1-L9 and d0-d9. L9
is the lightest, d0 is the middle,
and d9 is the darkest setting.
3. To save the light/dark value,
press the PROGRAM button or
wait 5 seconds until the screen
displays “USE”.
NOTICE: Adjusting the light/dark
value does NOT change the
temperature. It changes the
speed of the conveyors. The
light/dark value will reset to
the default value of d0 when
the unit is turned o󰀨.

6P/N 1012011 Rev. C 06/18
User Mode
User Mode allows an operator to
view the toaster settings but does
not permit any adjustments.
1. Press and hold the PROGRAM
button for 5 seconds. After 5
seconds, the display will show
the actual temperature of the
Platen.
2. Press the LIGHTER button to
toggle between the Setpoint and
actual temperature of the Platen
Heater.
3. Press the PROGRAM button to
proceed to the Motor Menu. The
display shows the actual speed
of the motor.
4. Press the LIGHTER button to
toggle between the Setpoint and
actual speed of the Motor.
NOTICE: The unit will exit User
Mode after 5 seconds of
keypad inactivity.
Error Codes
If any of the following Error Codes
appear, press and release the Power
button to turn the toaster o󰀨. Al-
low the unit to cool. Then press and
release the Power button to turn the
toaster on. If the error repeats, contact
Antunes Technical Service for assis-
tance.
NOTICE: ERR #1, 2 , 3, 5, 6, 7, and
30 to 51: Internal Error. Cycle
the power. If error persists,
replace the board.
Error Description
ERR
8
Motor running when it
should be o󰀨.
ERR
9
High Internal Temperature.
ERR
10
Shorted Thermocouple.
ERR
11
Open Thermocouple.
Manager Mode
Manager Mode allows an opera-
tor to view and adjust the following
settings:
yHeater Temperature
yMotor Speed
yTemperature Units
(Celsius or Fahrenheit)
Manager Mode also allows an
operator to view (but not adjust) the
Ambient Temperature of the Control
Compartment.
1. Press and release the Power
button to turn the toaster o󰀨.
2. Press and release the Power
button while holding the PRO-
GRAM button. Continue holding
the button until “ENA” appears
on the display (after approxi-
mately 10 seconds).
3. Release the PROGRAM button.
The display shows the Heater
Setpoint Temperature.
4. To adjust the Heater Setpoint
Temperature, press the LIGHT-
ER or DARKER buttons to
reach the desired temperature.
NOTICE: The recommended
temperature setting for the
Platen is 545 °F (285 °C).dd
5. Press the PROGRAM button to
procedure to the Motor Speed
Setpoint.
6. Adjust the Motor Speed Setpoint
by pressing the LIGHTER or
DARKER buttons to reach the
desired speed.
NOTICE: The Motor Speed is
adjustable from 1-100. The
recommended setting is 57.
7. Press the PROGRAM button
to proceed to the Temperature
Units.
8. To change the Temperatures
units from Fahrenheit or Cel-
sius, press the LIGHTER or
DARKER buttons.
9. Press and hold the PROGRAM
button to save any changes.
NOTICE: The unit exits Manager
Mode after 30 seconds of
keypad inactivity.
Safety Features
Hi-Limit Control
A Hi-Limit Control turns o󰀨 electri-
cal power to the heaters and control
circuits and displays HL if the unit
overheats. To reset the control:
1. Let the unit cool for 15 minutes.
2. Locate the Hi-Limit Controls on
the rear of the unit. Remove the
black protective cap.
3. Press and release the button.
Re-install the protective cap.
NOTICE: If the Hi-Limit Control
requires continuous reset-
ting, contact your Authorized
Service Agency.
Purging Buns from Toaster
If buns get stuck in the toaster,
press and hold both the UP and
DOWN arrow buttons to increase
the belt speed until the buns are
purged from the toaster.
Fault Messages
The unit displays fault messages
when there is a problem with the
unit.
y“Hi” ashes if the Platen
Heater temperature is 30 °F
more than the Setpoint or
if the Platen Thermocouple
is disconnected or open.
y“CHEC” ashes when the
control compartment ambient
temperature is more than 150
°F (66 °C). All heaters shut
o󰀨. The unit will not restart
until the control compartment
ambient temperature falls
below 140 °F (60 °C).
y“PO” ashes if the incoming
power drops below 190 volts.
The toaster shuts down.
y“StoP” ashes when the
motor has stopped for seven
continuous seconds.
y“SpEd” ashes when the
motor speed drops 25%
below the Setpoint for 30
continuous seconds.
y“PLt” slow warmup (2:20 Min)
y“SSr” The Solid State Relay
has shorted - the unit is running
beyond the setpoint temperature.

7
P/N 1012011 Rev. C 06/18
Daily Cleaning
Clean Toaster and Belt Wraps
1. Press and release the Power
button to turn the unit o󰀨. The unit
enters a 45 minutes cool-down
mode and automatically shuts
down when complete.
NOTICE: The belt rollers will continue
turning while in cool-down
mode. This allows the entire
belt to be cleaned.
2. Put on heat resistant gloves. Re-
move the Top Cover, Feeder, and
Chute (Figure 1).
3. Wash, rinse and sanitize the Top
Cover, Feeder, and Chute at the
3-compartment sink.
Inspect the belts
NOTICE: Replace any belts that are
torn, folded, missing snaps,
or damaged. Belts should be
removed ONLY during belt re-
placement or when required in
a service situation (see images
on page 9 for examples). Refer
to the section titled Replacing
Belts for instructions on remov-
ing and installing belts.
1. Apply a small amount of KAY®
QSR Heat-Activated Grill & Toaster
Cleaner on a non-abrasive pad.
2. Wash step – Wipe with the non-
abrasive pad damped with the Grill
& Toaster Cleaner.
3. Rinse step – Wipe with a clean
towel dampened with water.
4. Sanitize step – Wipe with a clean
towel soaked in KAYQUAT® II
Sanitizer solution and allow to air
dry.
5. Clean the top and bottom belts
(each belt should follow the
Wash-Rinse-Sanitize step):
NOTICE: Repeat Steps 3 and 4
as needed to remove heavy
carbon buildup. Be sure to
wash-rinse-sanitize the belts
completely. Failure to properly
clean the belts will shorten the
life of the belts and result in
poor performance.
6. Wipe the exterior surfaces of the
unit with a clean, sanitizer-soaked
towel and allow to air dry.
7. Reinstall all accessories (Figure 1).
8. Turn n the unit on and test the unit
before returning it to operation.
Examples of damaged belts
Replace torn or folded belts
Replace the belt if snaps are missing or
damaged.
Replace belts that are wrinkled or distressed
around snaps or with snaps that are loose,
damaged, or missing.

8P/N 1012011 Rev. C 06/18
Quarterly Cleaning
Remove Belt Wraps and Clean
Rollers
1. Turn the toaster’s power switch
to the o󰀨 position. The toaster
enters a cool-down mode and
will automatically shut down
when complete.
2. Unplug the power cord once the
cool-down period is complete.
NOTICE: Wait for the cool-down
period to complete before
unplugging the power cord.
3. Remove the bun feeder using
heat-resistant gloves.
NOTICE: Reposition the toaster
as needed to perform these
steps.
4. Unlock the lock on the right side
panel with a athead screw-
driver and open the panel. Turn
the compression knobs (there
are 2) to 7.
Loose
Loose
Figure 2. Loosening the conveyor
rollers
5. Remove tension on the Top
Belt by pushing the Top FRONT
Roller IN and UP until it locks
into position.
6. Remove tension on the Bot-
tom Belt by pushing the Bottom
FRONT Roller IN and DOWN.
7. Unlock the Top and bottom lock
levers. (See below).
Upper Frame
Belt Lock
Unlocked
Lower Frame
Belt Lock
Unlocked
Figure 3. Conveyor locks
8. Carefully remove the two top
belts and one bottom belt.
Upper Belt Wraps
Lower Belt
Wrap
Figure 4. Belt Wraps
9. Wipe all four rollers and back-
ing plates with a clean, damp
sanitized towel. Make sure to re-
move all debris from the rollers
and the backing plates so they
are as clean as possible.
10. Use a dry cloth towel or nylon-
bristled brush to remove all
debris from both side compart-
ments, inside of the toaster, and
underneath the rollers.
Install Belt Wraps
1. If you are installing the existing
belt wraps, inspect the belts.
Replace belt wraps if worn or
damaged. If the belt wraps are
in good condition put them back
on the toaster.
2. For new or existing belts, wipe
both sides of the belts with a
clean, damp sanitized towel. Al-
low to air dry.
3. Slide the belts gently over the
appropriate top and bottom
roller. Make sure the belt lines
up properly on the rollers. The
snaps on the belts should face
the inside of the roller.
4. Restore tension on the bottom
belt by pushing UP and OUT
(See Below).
5. Restore the tension on the top
belt by pushing DOWN and
OUT (See Below).
Tense
Tense
Figure 5. Conveyor rollers under
tension
NOTICE: Lift up on the camshaft of
the rear conveyor roller while lifting
the conveyor lock.
Upper Frame
Belt Lock
Engaged
Lower Frame
Belt Lock
Engaged
Figure 6. Belt frame locks
6. Engage the top and bottom lock
levers as shown above. Make
sure the lock lever is properly in-
serted into the slotted grooves.
7. Close the side panel and lock
the lock using a athead screw-
driver on the side panel.
8. Set the Crown compression
knob to 4 and the Heel to 3.
9. Re install the top cover and bun
feeder onto the unit.
10. Plug in the power cord and turn
the unit on.

9
P/N 1012011 Rev. C 06/18
Annual Cleaning
Clean Cooling Fans and
Electrical Housings
1. Turn the toaster’s power switch
to the o󰀨 position. The toaster
enters a cool-down mode and
will automatically shut down
when complete. Unplug the
power cord.
2. Remove the push knob and top
six screws on the left side of the
toaster and set aside.
Using the handle, remove the left
side cover of the unit by lifting up
and away from the unit. Set aside.
Figure 7. Accessing the cooling fan
3. Remove any debris or dust from
the cooling fan with a small
brush. Wipe away any debris
with a clean, dry towel Inspect
the electrical compartment for
crumbs and debris. Clean out
all crumbs and debris using a
clean, dry towel or nylon bristled
brush. Be careful not to disrupt
any of the electrical wiring.
4. Replace the left side panel
cover by sliding it onto the bot-
tom screws.
5. Reconnect with the screws and
replace Push on Knob.

10 P/N 1012011 Rev. C 06/18
Problem Possible Cause Corrective Action
Control Display ashes
PLt continuously. Buns
not toasting properly.
Platen temperature is below 545 °F
(285 °C).
Allow the unit to warm up for 30 minutes and then
recheck. If the Control Display still ashes PLt,
contact your maintenance person or Antunes
Technical Service for service.
Failed Platen Thermocouple. Contact your maintenance person or Antunes
Technical Service for service.
Failed Control Board
Control Display ashes
Er 9 continuously.
Control Compartment ambient tem-
perature is above 150 °F (66 °C)
Verify side vents on toaster are unblocked and not
near other heating appliances. If problem persists
contact your maintenance person or Antunes
Technical Service for service.
Failed Cooling Fan.
Failed Control Board
Control Display Flashes
SSr continuously. Buns
Burn.
Failed Front Platen Solid State
Relay.
Contact your maintenance person or Authorized
Service Agency for service.
Failed Control Board.
Failed Front Platen Thermocouple.
Control Display ashes
Er 11 continuously. Buns
not toasting properly.
Loose Platen Thermocouple con-
nection on Control Board or the
Platen Thermocouple is open.
Re-secure the Platen Thermocouple to the Control
Board. If the Control Display still reads Er 11,
check the Thermocouple for continuity.Contact
your maintenance person or Antunes Technical
Service for service.
Failed Control Board.
Control Display ashes
Er 10 continuously. Buns
not toasting properly.
Shorted Platen Thermocouple to
ground.
Disconnect and re-secure the Platen Thermocou-
ple connection to the Control Board. If the Control
Display still reads Er 10, check the Thermocouple
for continuity. Contact your maintenance person or
Antunes Technical Service for service.
Failed Control Board
Control Display ashes
StoP.
Mechanical bind in one or both
conveyors.
Enter “user mode” to check the motor speed.
Check both conveyors for mechanical binds. Test
the motor. Replace necessary parts. Contact your
maintenance person or Antunes Technical Service
for service.
Worn or damaged Ball Bearings.
Drive chain or sprockets damaged.
Failed Motor.
Failed Control Board.
Control Display ashes
SpEd.
Mechanical bind in one or both
conveyors.
Enter “user mode” to check motor speed. Check
both conveyors for mechanical binds. Replace
necessary parts. Contact your maintenance per-
son or Authorized Service Agency for service.
Worn or damaged Ball Bearings.
Conveyor chains loose or damaged.
Drive chain or sprockets damaged.
Crowns and/or Heels
must be forced into the
toaster. Buns sticking
and burning.
Belts are dirty, worn, or damaged
(replace every 2-4 months).
Clean or replace Belts as described in the Mainte-
nance section of this manual.
Buns do not meet specications. Contact your bun supplier.
Troubleshooting

11
P/N 1012011 Rev. C 06/18
Problem Possible Cause Corrective Action
Buns not toasting ad-
equately.
Compression Setting is incorrect. Use the recommended setting of 4 for Crowns and
3 for Heels.
One of the Conveyor shafts is stuck
in the lower lock position.
Inspect positions of the shafts as described in the
Maintenance section of this manual.
Either both Upper/Lower Conveyor
locks are not properly locked in
place.
Inspect the proper position of the locks as de-
scribed in the Maintenance section of this manual.
Buns do not meet specications. Contact your bun supplier.
Motor settings are incorrect. Verify that the motor setting is set to 4000 as
described in the Programming section of this
Manual.
Compression side door
will not close.
Either both Upper/Lower Conveyor
Locks are not properly locked in
place.
Inspect the proper position of the locks as de-
scribed in the Maintenance section of this manual.
The lock on the Compression Side
Door is in the locked position when
trying to close the door.
Turn the lock to the unlocked position before clos-
ing the door.
Fan is making an un-
usual sound.
Failed Cooling Fan. Verify vents on toaster are unblocked and not near
other heating appliances. Clean fans as described
in the Maintenance section of this manual. If prob-
lem persists, contact your maintenance person or
Antunes Technical Service for service.
Cooling Fan is dirty and needs to be
cleaned.
Control Display ashes
HL continuously. Buns
are not toasting properly.
Hi-Limit Control is tripped. Allow the unit to cool and reset the Hi-Limit Con-
trol. If it trips again, contact your maintenance
person or Antunes Technical Service for service.
Control Display is blank. Power Cord is not plugged in. Plug the Power Cord into the appropriate out-
let. Turn the toaster on. If the Control Display is
still blank, contact your maintenance person or
Antunes Technical Service for service.
Circuit Breakers turned o󰀨 or
tripped. Damaged electrical outlet,
plug, or Power Cord. Power Switch
damaged.
Reset Circuit Breakers. If they trip again, check
the Power Cord, Plug, and outlet for damage.
Contact your maintenance person or Antunes
Technical Service for service.
Faulty Transformer. Replace Transformer.
Conveyors not turning. Belt is damaged. Replace Belts
Motor Drive Chain is detached from
sprockets.
Reinstall the Drive Chain.
Failed Drive Motor. Contact your maintenance person or Antunes
Technical Service for service.
Belts are ripped or torn. Rollers or Heater Cover Plates are
dirty and need to be cleaned.
Clean Rollers and Heater Cover Plates as outlined
in the Maintenance section of this manual.
Belts are not installed properly. Install Belts correctly as outlined in the Mainte-
nance section of this manual.
Roller(s) in the incorrect locked
position during operation.
Unlock Rollers to operational position.
Front Conveyor Lock is disengaged. Engage and lock the Front Conveyor Lock.

12 P/N 1012011 Rev. C 06/18
Replacement Parts
2
17
64
50
51
49
66
9
56
9
66
6
56
14
13
42
42
68
6824
31
30
52
52
68
43
23
82
82
78
18
45
40
64
35
64
64
33
39
50
68
26
NOTICE: Use only genuine
Antunes replacement
parts in this egg station.
Use of parts other than
those supplied by the
manufacturer will void
the warranty.
Parts List
Item
No.
Part # Description Qty.
1 0012913 Insulator Assembly 1
2 0012961 Door Assembly 1
3
0013024 Platen Assembly (Mfg. No.
9210961) 1
0013234 Platen Assembly (Mfg. No.
9210962) 1
4 0013025 Drive Motor Assy 1
5 0013093 Brkt Assy Top 1
6 0013094 Brkt Assy Bottom 1
7 0013095 Bearing Brkt Assy 2
8 0013096 Adjustable Frame Assy 1
9 0013104 Brg Cover Assy 2
10 0013109 Duct Assembly 1
11
0013110 Housing Door Assy (Mfg. No.
9210961) 1
0013249 Housing Door Assy (Mfg. No.
9210962) 1
12 0013111 Assy, Drive Chain Tensioner 1
13 0021724 Weldment, Brg Brkt & Spring
Guide - RH 2
14 0021725 Wldmnt, Bearing Brkt & Spring
Guide LH 2
15 0021865 Main Platen Frame Wldmt 1
Item
No.
Part # Description Qty.
16 0021885 End Housing Weldment 1
17 0021897 End Housing Panel Wldmt 1
18 0021940 Base Weldment 1
19 0021953 Weldment, Drive Roller Adjust
Lanes 1
20 0021954 Weldment, Idler Adjust Lanes 1
21 0021976 Wldmt, Drive Roller Main
Platen 1
22 0021977 Wldmt, Idler Roller Main
Platen 1
23 0022007 Top Hinge Lock Weldmt 1
24 0022008 Bottom Hinge Lock Weldmt 1
25 0022043 Control Housing Weldment 1
26 0022105 Cover Weldment 1
27 0400119 Bushing, Shorty 5/8” (Mfg. No.
9210961 Only) 3
28 0400354 Strain Relief 1
29 0400432 Bushing, Open/Closed 1
30 0506543 Plate, Tensioner LH 1
31 0506544 Plate, Tensioner RH 1
32 0506556 Base Bottom Side 1
33 0506562 Ele Cover 1
34 0506566 Plate, Tensioner 2
35 0506835 Bun Stop 1

13
P/N 1012011 Rev. C 06/18
PARTS LIST
ITEM PART NO. DESCRIPTION QTY
4.9 3100199 SCR, #10-32 X 3/8 LG SOCKET
HD CAP
4
85 3100199 SCR, #10-32 X 3/8 LG SOCKET
HD CAP
8
4.9, 85 3100199 SCR, #10-32 X 3/8 LG SOCKET
HD CAP
12
10013024 PLATEN ASSY 1
20013093 BRKT ASSY TOP 1
3 0013094 BRKT ASSY BOTTOM 1
40013095 BEARING BRKT ASSY 2
50013096 ADJUSTABLE FRAME ASSY 1
6 0013104 BRG COVER ASSY 2
70013111 ASSY, DRIVE CHAIN
TENSIONER
1
8 0021724 WELDMENT, BRG BRKT &
SPRING GUIDE - RH
2
9 0021725 WEDMENT, BEARING
BRACKET & SPRING GUIDE -
LH
2
10 0021865 MAIN PLATEN FRAME WLDMT 1
11 0021885 END HOUSING WELDMENT 1
12 0021894 WELDMENT, END COVER
LOCK
1
13 0021895 DOOR WELDMENT 1
14 0021897 END HOUSING PANEL WLDMT 1
15 0021916 ELE BRACKET WLDMT 1
17 0021950 PANEL WELDMENT CONTROL
HSG
1
18 0021953 WELDMENT, DRIVE ROLLER
ADJUST LANES
1
19 0021954 WELDMENT, IDLER ADJUST
LANES
1
20 0021976 WLDMT, DRIVE ROLLER MAIN
PLATEN
1
21 0021977 WLDMT, IDLER ROLLER MAIN
PLATEN
1
PARTS LIST
ITEM PART NO. DESCRIPTION QTY
22 0022007 TOP HINGE LOCK WELDMT 1
23 0022008 BOTTOM HINGE LOCK
WELDMT
1
24 0022043 CONTROL HOUSING
WELDMENT
1
25 0022105 COVER WELDMENT 1
26 0400119 BUSHING, SHORTY 5/8" 3
27 0400251 STRAIN RELIEF-CORD
CONNECTOR
1
28 0400432 BUSHING, OPEN/CLOSED 1
29 0506083 SPACER .075 THK .203 ID X
.312 OD
2
30 0506157 MOTOR PLATE 1
31 0506543 PLATE, TENSIONER LH 1
32 0506544 PLATE, TENSIONER RH 1
33 0506556 BASE BOTTOM SIDE 1
34 0506562 ELE COVER 1
35 0506566 PLATE, TENSIONER 2
36 0506835 BUN STOP 1
37 0506836 WASHER 1
38 0506839 BEARING RETAINER BRKT 1
39 0506853 FRAME COVER 1
40 0506860 BACK COVER 1
41 0506862 DUCT 1
42 0506864 BUN RAMP 1
43 0600143 SPRING, COMPRESSION
SETTING
1
44 0600158 SPRING, ROLLER TENSION 4
PARTS LIST
ITEM PART NO. DESCRIPTION QTY
45 0600161 TORSION SPRING, LOCKING
BRACKET TOP
1
46 0700737 POWER CORD 20A, 250V
RIGHT ANGLE
1
47 0800467 BUN CHUTE 1
48 0800473 ROD, HSG SPACER 14.375 LG 4
49 1000136 EMBLEM, ROUNDUP 1
50 1000900 LABEL - WARNING 1
51 1001192 LABEL, CAUTION - "HOT" 1
52 1001213 LABEL - SHOCK HAZARD 1
53 1001505 LABEL, CONTROL 1
54 1001585 LABEL, COMPRESSION LH 1
55 1001586 LABEL, COMPRESSION- RH 1
56 1001589 LABEL, WIRE DIAGRAM
WENDY'S
1
57 2100212 HANDLE, POCKET PULL,
SNAP-IN
1
58 2100212 HANDLE, POCKET PULL,
SNAP-IN
2
58, 57 2100212 HANDLE, POCKET PULL,
SNAP-IN
3
59 2100253 KNOB, 1/4" SHAFT, PUSH-ON 2
60 2100334 THRUST STRIP, TEFLON 4
61 2110197 CLIP, STEEL CABLE 1
62 2120233 SPACER .252 ID X .5 OD X
.925" LG
4
63 2120259 SPACER, .38OD X .13THK #8
SCREW
2
64 2140109 LOCTITE # 242 (BLUE) 1
65 2150185 SPROCKET, 25B18, 1/2" BORE 2
66 2150378 SPROCKET, 25B20 3/8" BORE 1
PARTS LIST
ITEM PART NO. DESCRIPTION QTY
67 2150384 BEARING ASSY, HI-TEMP 1
1/8" OD X 1/2" ID
8
68 2150393 DRIVE CHAIN 1
69 3040105 NUT, HEX 'KEPS' #4-40 5
70 3040105 NUT, HEX 'KEPS' #4-40 2
70, 69 3040105 NUT, HEX 'KEPS' #4-40 7
71 3060130 NUT, HEX KEPS #6-32 (SMALL
PATTERN)
9
72 3060130 NUT, HEX KEPS #6-32 (SMALL
PATTERN)
2
72, 71 3060130 NUT, HEX KEPS #6-32 (SMALL
PATTERN)
11
73 3080124 SCREW, MACH ONE-WAY
#8-32
1
74 3080143 NUT, HEX 'KEPS' #8-32 2
75 3080145 NUT, HEX ACORN #08-32 LOW
CROWN
1
76 3080199 NUT, HEX 'KEPS' #8-32 4
77 3080203 SCREW, TAP 8-32 X 3/8"
W/INT. TOOTH WASHER
4
78 3080203 SCREW, TAP 8-32 X 3/8"
W/INT. TOOTH WASHER
33
78, 77 3080203 SCREW, TAP 8-32 X 3/8"
W/INT. TOOTH WASHER
37
79 3080223 WASHER, FLAT #8 2
80 3080340 NUT, HEX ACORN LOCK #8-32 2
81 3100102 WASHER, INT.
TOOTH-LOCK,#10
8
82 3100146 NUT, HEX 'KEPS' #10-32 26
83 3100187 SCREW SET, #10-32 X 3/8 HEX
SOCKET-CONE POINT
2
84 3100196 SCREW, SHOULDER 10-32 SS 4
87 3100204 FILLISTER HEAD PHILLIPS
SCREW # 10-32 X .25
2
88 3100213 SCREW, PHPNHD #10-16 X
3/4" THRD FORM
4
PARTS LIST
ITEM PART NO. DESCRIPTION QTY
89 3100214 SCREW, HEX #10-32 X 1/2" 4
90 3250109 SCREW, HEXCAP 1/4-20 X 1/2" 9
91 3250154 WASHER, Ă1/4" HELICAL
SPRING LOCK
4
92 3250177 1
93 3250193 SCREW, HEX HEAD, #1/4-20 X
1.375", S.S.
4
94 4000186 MOTOR, 230V 1
95 4000202 FAN, AXIAL - 230V, METAL
HOUSING & IMP
1
96 4010187 TRANSFORMER, 240
VAC/12VAC
1
97 4010221 CAP-MP, MOTOR RUN 1
98 4030352 THERMOSTAT, HI-LIMIT 700ĀF 1
99 4030446 HTR, FOIL 208V, 35W .25
FEMALE TERMINALS
1
100 4050214 THERMOCOUPLE TYPE "K"
(OPEN END)
1
101 4050236 CONTACTOR, 2 POLE NO 1
102 4051010 RELAY, RANDOM PHASE,
SOLID STATE-50A
1
103 4060374 GROUND LUG 1
104 4070154 VARISTOR BOARD 1
105 4070183 1
106 5040022 4
107 5040022a 1
108 7000984 MAIN BELT 1
109 7000991 CROWN & HEEL BELT 2
312 0507140 ALUM WASHER 2
313 0013115 BASE ASSEMBLY 1
101
72
15
102
77
96
77
53
105
46
27
8
44
44
60
35
100
60
35
67
67
4
4
82
4.9
67
38
82
94
30
89
65
83
65
43
66
7
88
41
95
71
17
78
57
54
59
98
76
76
71
104
70
52
50
83
PARTS LIST
ITEM PART NO. DESCRIPTION QTY
4.9 3100199 SCR, #10-32 X 3/8 LG SOCKET
HD CAP
4
85 3100199 SCR, #10-32 X 3/8 LG SOCKET
HD CAP
8
4.9, 85 3100199 SCR, #10-32 X 3/8 LG SOCKET
HD CAP
12
10013024 PLATEN ASSY 1
20013093 BRKT ASSY TOP 1
3 0013094 BRKT ASSY BOTTOM 1
40013095 BEARING BRKT ASSY 2
50013096 ADJUSTABLE FRAME ASSY 1
6 0013104 BRG COVER ASSY 2
70013111 ASSY, DRIVE CHAIN
TENSIONER
1
8 0021724 WELDMENT, BRG BRKT &
SPRING GUIDE - RH
2
9 0021725 WEDMENT, BEARING
BRACKET & SPRING GUIDE -
LH
2
10 0021865 MAIN PLATEN FRAME WLDMT 1
11 0021885 END HOUSING WELDMENT 1
12 0021894 WELDMENT, END COVER
LOCK
1
13 0021895 DOOR WELDMENT 1
14 0021897 END HOUSING PANEL WLDMT 1
15 0021916 ELE BRACKET WLDMT 1
17 0021950 PANEL WELDMENT CONTROL
HSG
1
18 0021953 WELDMENT, DRIVE ROLLER
ADJUST LANES
1
19 0021954 WELDMENT, IDLER ADJUST
LANES
1
20 0021976 WLDMT, DRIVE ROLLER MAIN
PLATEN
1
21 0021977 WLDMT, IDLER ROLLER MAIN
PLATEN
1
PARTS LIST
ITEM PART NO. DESCRIPTION QTY
22 0022007 TOP HINGE LOCK WELDMT 1
23 0022008 BOTTOM HINGE LOCK
WELDMT
1
24 0022043 CONTROL HOUSING
WELDMENT
1
25 0022105 COVER WELDMENT 1
26 0400119 BUSHING, SHORTY 5/8" 3
27 0400251 STRAIN RELIEF-CORD
CONNECTOR
1
28 0400432 BUSHING, OPEN/CLOSED 1
29 0506083 SPACER .075 THK .203 ID X
.312 OD
2
30 0506157 MOTOR PLATE 1
31 0506543 PLATE, TENSIONER LH 1
32 0506544 PLATE, TENSIONER RH 1
33 0506556 BASE BOTTOM SIDE 1
34 0506562 ELE COVER 1
35 0506566 PLATE, TENSIONER 2
36 0506835 BUN STOP 1
37 0506836 WASHER 1
38 0506839 BEARING RETAINER BRKT 1
39 0506853 FRAME COVER 1
40 0506860 BACK COVER 1
41 0506862 DUCT 1
42 0506864 BUN RAMP 1
43 0600143 SPRING, COMPRESSION
SETTING
1
44 0600158 SPRING, ROLLER TENSION 4
PARTS LIST
ITEM PART NO. DESCRIPTION QTY
45 0600161 TORSION SPRING, LOCKING
BRACKET TOP
1
46 0700737 POWER CORD 20A, 250V
RIGHT ANGLE
1
47 0800467 BUN CHUTE 1
48 0800473 ROD, HSG SPACER 14.375 LG 4
49 1000136 EMBLEM, ROUNDUP 1
50 1000900 LABEL - WARNING 1
51 1001192 LABEL, CAUTION - "HOT" 1
52 1001213 LABEL - SHOCK HAZARD 1
53 1001505 LABEL, CONTROL 1
54 1001585 LABEL, COMPRESSION LH 1
55 1001586 LABEL, COMPRESSION- RH 1
56 1001589 LABEL, WIRE DIAGRAM
WENDY'S
1
57 2100212 HANDLE, POCKET PULL,
SNAP-IN
1
58 2100212 HANDLE, POCKET PULL,
SNAP-IN
2
58, 57 2100212 HANDLE, POCKET PULL,
SNAP-IN
3
59 2100253 KNOB, 1/4" SHAFT, PUSH-ON 2
60 2100334 THRUST STRIP, TEFLON 4
61 2110197 CLIP, STEEL CABLE 1
62 2120233 SPACER .252 ID X .5 OD X
.925" LG
4
63 2120259 SPACER, .38OD X .13THK #8
SCREW
2
64 2140109 LOCTITE # 242 (BLUE) 1
65 2150185 SPROCKET, 25B18, 1/2" BORE 2
66 2150378 SPROCKET, 25B20 3/8" BORE 1
PARTS LIST
ITEM PART NO. DESCRIPTION QTY
67 2150384 BEARING ASSY, HI-TEMP 1
1/8" OD X 1/2" ID
8
68 2150393 DRIVE CHAIN 1
69 3040105 NUT, HEX 'KEPS' #4-40 5
70 3040105 NUT, HEX 'KEPS' #4-40 2
70, 69 3040105 NUT, HEX 'KEPS' #4-40 7
71 3060130 NUT, HEX KEPS #6-32 (SMALL
PATTERN)
9
72 3060130 NUT, HEX KEPS #6-32 (SMALL
PATTERN)
2
72, 71 3060130 NUT, HEX KEPS #6-32 (SMALL
PATTERN)
11
73 3080124 SCREW, MACH ONE-WAY
#8-32
1
74 3080143 NUT, HEX 'KEPS' #8-32 2
75 3080145 NUT, HEX ACORN #08-32 LOW
CROWN
1
76 3080199 NUT, HEX 'KEPS' #8-32 4
77 3080203 SCREW, TAP 8-32 X 3/8"
W/INT. TOOTH WASHER
4
78 3080203 SCREW, TAP 8-32 X 3/8"
W/INT. TOOTH WASHER
33
78, 77 3080203 SCREW, TAP 8-32 X 3/8"
W/INT. TOOTH WASHER
37
79 3080223 WASHER, FLAT #8 2
80 3080340 NUT, HEX ACORN LOCK #8-32 2
81 3100102 WASHER, INT.
TOOTH-LOCK,#10
8
82 3100146 NUT, HEX 'KEPS' #10-32 26
83 3100187 SCREW SET, #10-32 X 3/8 HEX
SOCKET-CONE POINT
2
84 3100196 SCREW, SHOULDER 10-32 SS 4
87 3100204 FILLISTER HEAD PHILLIPS
SCREW # 10-32 X .25
2
88 3100213 SCREW, PHPNHD #10-16 X
3/4" THRD FORM
4
PARTS LIST
ITEM PART NO. DESCRIPTION QTY
89 3100214 SCREW, HEX #10-32 X 1/2" 4
90 3250109 SCREW, HEXCAP 1/4-20 X 1/2" 9
91 3250154 WASHER, Ă1/4" HELICAL
SPRING LOCK
4
92 3250177 1
93 3250193 SCREW, HEX HEAD, #1/4-20 X
1.375", S.S.
4
94 4000186 MOTOR, 230V 1
95 4000202 FAN, AXIAL - 230V, METAL
HOUSING & IMP
1
96 4010187 TRANSFORMER, 240
VAC/12VAC
1
97 4010221 CAP-MP, MOTOR RUN 1
98 4030352 THERMOSTAT, HI-LIMIT 700ĀF 1
99 4030446 HTR, FOIL 208V, 35W .25
FEMALE TERMINALS
1
100 4050214 THERMOCOUPLE TYPE "K"
(OPEN END)
1
101 4050236 CONTACTOR, 2 POLE NO 1
102 4051010 RELAY, RANDOM PHASE,
SOLID STATE-50A
1
103 4060374 GROUND LUG 1
104 4070154 VARISTOR BOARD 1
105 4070183 1
106 5040022 4
107 5040022a 1
108 7000984 MAIN BELT 1
109 7000991 CROWN & HEEL BELT 2
312 0507140 ALUM WASHER 2
313 0013115 BASE ASSEMBLY 1
101
72
15
102
77
96
77
53
105
46
27
9
8
44
44
60
35
100
60
35
67
67
4
4
82
4.9
67
38
82
30
89
65
83
65
43
66
7
88
41
95
71
17
78
57
54
59
76
76
71
104
70
52
50
83
PARTS LIST
ITEM PART NO. DESCRIPTION QTY
4.9 3100199 SCR, #10-32 X 3/8 LG SOCKET
HD CAP
4
85 3100199 SCR, #10-32 X 3/8 LG SOCKET
HD CAP
8
4.9, 85 3100199 SCR, #10-32 X 3/8 LG SOCKET
HD CAP
12
10013024 PLATEN ASSY 1
20013093 BRKT ASSY TOP 1
3 0013094 BRKT ASSY BOTTOM 1
40013095 BEARING BRKT ASSY 2
50013096 ADJUSTABLE FRAME ASSY 1
6 0013104 BRG COVER ASSY 2
70013111 ASSY, DRIVE CHAIN
TENSIONER
1
8 0021724 WELDMENT, BRG BRKT &
SPRING GUIDE - RH
2
9 0021725 WEDMENT, BEARING
BRACKET & SPRING GUIDE -
LH
2
10 0021865 MAIN PLATEN FRAME WLDMT 1
11 0021885 END HOUSING WELDMENT 1
12 0021894 WELDMENT, END COVER
LOCK
1
13 0021895 DOOR WELDMENT 1
14 0021897 END HOUSING PANEL WLDMT 1
15 0021916 ELE BRACKET WLDMT 1
17 0021950 PANEL WELDMENT CONTROL
HSG
1
18 0021953 WELDMENT, DRIVE ROLLER
ADJUST LANES
1
19 0021954 WELDMENT, IDLER ADJUST
LANES
1
20 0021976 WLDMT, DRIVE ROLLER MAIN
PLATEN
1
21 0021977 WLDMT, IDLER ROLLER MAIN
PLATEN
1
PARTS LIST
ITEM PART NO. DESCRIPTION QTY
22 0022007 TOP HINGE LOCK WELDMT 1
23 0022008 BOTTOM HINGE LOCK
WELDMT
1
24 0022043 CONTROL HOUSING
WELDMENT
1
25 0022105 COVER WELDMENT 1
26 0400119 BUSHING, SHORTY 5/8" 3
27 0400251 STRAIN RELIEF-CORD
CONNECTOR
1
28 0400432 BUSHING, OPEN/CLOSED 1
29 0506083 SPACER .075 THK .203 ID X
.312 OD
2
30 0506157 MOTOR PLATE 1
31 0506543 PLATE, TENSIONER LH 1
32 0506544 PLATE, TENSIONER RH 1
33 0506556 BASE BOTTOM SIDE 1
34 0506562 ELE COVER 1
35 0506566 PLATE, TENSIONER 2
36 0506835 BUN STOP 1
37 0506836 WASHER 1
38 0506839 BEARING RETAINER BRKT 1
39 0506853 FRAME COVER 1
40 0506860 BACK COVER 1
41 0506862 DUCT 1
42 0506864 BUN RAMP 1
43 0600143 SPRING, COMPRESSION
SETTING
1
44 0600158 SPRING, ROLLER TENSION 4
PARTS LIST
ITEM PART NO. DESCRIPTION QTY
45 0600161 TORSION SPRING, LOCKING
BRACKET TOP
1
46 0700737 POWER CORD 20A, 250V
RIGHT ANGLE
1
47 0800467 BUN CHUTE 1
48 0800473 ROD, HSG SPACER 14.375 LG 4
49 1000136 EMBLEM, ROUNDUP 1
50 1000900 LABEL - WARNING 1
51 1001192 LABEL, CAUTION - "HOT" 1
52 1001213 LABEL - SHOCK HAZARD 1
53 1001505 LABEL, CONTROL 1
54 1001585 LABEL, COMPRESSION LH 1
55 1001586 LABEL, COMPRESSION- RH 1
56 1001589 LABEL, WIRE DIAGRAM
WENDY'S
1
57 2100212 HANDLE, POCKET PULL,
SNAP-IN
1
58 2100212 HANDLE, POCKET PULL,
SNAP-IN
2
58, 57 2100212 HANDLE, POCKET PULL,
SNAP-IN
3
59 2100253 KNOB, 1/4" SHAFT, PUSH-ON 2
60 2100334 THRUST STRIP, TEFLON 4
61 2110197 CLIP, STEEL CABLE 1
62 2120233 SPACER .252 ID X .5 OD X
.925" LG
4
63 2120259 SPACER, .38OD X .13THK #8
SCREW
2
64 2140109 LOCTITE # 242 (BLUE) 1
65 2150185 SPROCKET, 25B18, 1/2" BORE 2
66 2150378 SPROCKET, 25B20 3/8" BORE 1
PARTS LIST
ITEM PART NO. DESCRIPTION QTY
67 2150384 BEARING ASSY, HI-TEMP 1
1/8" OD X 1/2" ID
8
68 2150393 DRIVE CHAIN 1
69 3040105 NUT, HEX 'KEPS' #4-40 5
70 3040105 NUT, HEX 'KEPS' #4-40 2
70, 69 3040105 NUT, HEX 'KEPS' #4-40 7
71 3060130 NUT, HEX KEPS #6-32 (SMALL
PATTERN)
9
72 3060130 NUT, HEX KEPS #6-32 (SMALL
PATTERN)
2
72, 71 3060130 NUT, HEX KEPS #6-32 (SMALL
PATTERN)
11
73 3080124 SCREW, MACH ONE-WAY
#8-32
1
74 3080143 NUT, HEX 'KEPS' #8-32 2
75 3080145 NUT, HEX ACORN #08-32 LOW
CROWN
1
76 3080199 NUT, HEX 'KEPS' #8-32 4
77 3080203 SCREW, TAP 8-32 X 3/8"
W/INT. TOOTH WASHER
4
78 3080203 SCREW, TAP 8-32 X 3/8"
W/INT. TOOTH WASHER
33
78, 77 3080203 SCREW, TAP 8-32 X 3/8"
W/INT. TOOTH WASHER
37
79 3080223 WASHER, FLAT #8 2
80 3080340 NUT, HEX ACORN LOCK #8-32 2
81 3100102 WASHER, INT.
TOOTH-LOCK,#10
8
82 3100146 NUT, HEX 'KEPS' #10-32 26
83 3100187 SCREW SET, #10-32 X 3/8 HEX
SOCKET-CONE POINT
2
84 3100196 SCREW, SHOULDER 10-32 SS 4
87 3100204 FILLISTER HEAD PHILLIPS
SCREW # 10-32 X .25
2
88 3100213 SCREW, PHPNHD #10-16 X
3/4" THRD FORM
4
PARTS LIST
ITEM PART NO. DESCRIPTION QTY
89 3100214 SCREW, HEX #10-32 X 1/2" 4
90 3250109 SCREW, HEXCAP 1/4-20 X 1/2" 9
91 3250154 WASHER, Ă1/4" HELICAL
SPRING LOCK
4
92 3250177 1
93 3250193 SCREW, HEX HEAD, #1/4-20 X
1.375", S.S.
4
94 4000186 MOTOR, 230V 1
95 4000202 FAN, AXIAL - 230V, METAL
HOUSING & IMP
1
96 4010187 TRANSFORMER, 240
VAC/12VAC
1
97 4010221 CAP-MP, MOTOR RUN 1
98 4030352 THERMOSTAT, HI-LIMIT 700ĀF 1
99 4030446 HTR, FOIL 208V, 35W .25
FEMALE TERMINALS
1
100 4050214 THERMOCOUPLE TYPE "K"
(OPEN END)
1
101 4050236 CONTACTOR, 2 POLE NO 1
102 4051010 RELAY, RANDOM PHASE,
SOLID STATE-50A
1
103 4060374 GROUND LUG 1
104 4070154 VARISTOR BOARD 1
105 4070183 1
106 5040022 4
107 5040022a 1
108 7000984 MAIN BELT 1
109 7000991 CROWN & HEEL BELT 2
312 0507140 ALUM WASHER 2
313 0013115 BASE ASSEMBLY 1
101
72
15
102
77
96
77
53
105
46
27
9
8
44
44
60
35
100
60
35
67
67
4
4
82
4.9
67
38
82
94
30
89
65
83
65
43
66
7
88
41
95
71
17
78
57
54
59
98
76
76
71
104
70
52
50
83
110
112
111
76
NOTICE: See Next Page for Parts
List related to this graphic.
NOTICE: Use only genuine
Antunes replacement
parts in this egg station.
Use of parts other than
those supplied by the
manufacturer will void
the warranty.

14 P/N 1012011 Rev. C 06/18
Parts List
Item
No.
Part # Description Qty.
1
0013234 Platen Assembly (Mfg. No.
9210961) 1
0013024 Platen Assembly (Mfg. No.
9210962) 1
2 0013093 Brkt Assy Top 1
3 0012094 Brkt Assy Bottom 1
4 0013095 Bearing Brkt Assy 2
5 0013096 Adjustable Frame Assy 1
6 0013104 Brg Cover Assy. 2
7 0013111 Assy, Drive Chain Tensioner 1
8 0021724 Weldment, Brg. Brkt. & Spring
Guide RH 2
9 0021725 Weldment, Brng Brkt & Spring
Guide LH 2
10 0021965 Main Platen Frame Weldment 1
11 0021885 End Housing Weldment 1
12 0021894 Weldment, End Cover Lock 1
13 0021895 Door Weldment
14 0021897 End Housing Panel Weldment 1
15 0021916 Ele. Bracket Weldment 1
17 0021950 Panel Weldment Control
Hsng. 1
18 0021953 Weldment, Drive Roller Adj.
Lanes 1
19 0021954 Weldment, Idler Adjust Lanes 1
20 0021976 Wldmnt, Drive Roller Main
Platen 1
21 0021977 Weldment, Idler, Roller Main
Platen 1
22 0022007 Top Hinge Lock Wldmnt 1
23 0022008 Bottom Hinge Lock Wldmnt 1
24 0022043 Control Housing Weldment 1
25 0022105 Cover Weldment 1
26 0400119 Busing, Shorty 5/8” (Mfg. No.
9210961 only) 3
27 0400251 Strain Relief Cord Connector 1
28 0400432 Bushing, Open/Closed 1
29 0506083 Spacer, .075 Thk .203 ID X
.3112 OD 2
30 0506157 Motor Plate 1
31 0506543 Plate, Tensioner LH 1
32 0506544 Plate, Tensioner RH 1
33 0506556 Base Bottom Side 1
34 0506562 Electrical Cover 1
35 0506566 Plate, Tensioner 2
36 0506835 Bun Stop 1
37 0506836 Washer 1
38 0506839 Bearing Retainer Brckt. 1
39 0506853 Frame Cover 1
40 0506860 Back Cover 1
41 0506862 Duct 1
42 0506864 Bun Ramp 1
43 0600143 Spring, Compression Setting 1
44 0600158 Spring, Roller Tension 4
45 0600161 Torsion Spring, Locking
Bracket Top 1
46
0700453
Power Cord CEE 7/7, 16
Amp.,250 VAC (Mfg. No.
9210961)
1
0700932
NEMA 6-20P 20 Amp, 250
Volt Right Angle (Mfg. No.
9210962)
1
47 0800467 Bun Chute 1
48 0800473 Rod, Hsg. Spacer 14.375 LG 4
50 1000900 Label, Warning 1
51 1001192 Label, Caution Hot 1
52 1001213 Label, Shock Hazard 1
53 1001505 Label, Control 1
54 1001585 Label, Compression LH 1
55 1001586 Label, Compression RH 1
Item
No.
Part # Description Qty.
56
1001643 Label, Wiring Diagram (Mfg.
No. 9210961) 1
1001589 Label ,Wiring Diagram (Mfg.
No. 9210962) 1
57 2100212 Handle, Pocket Pull Snap In 2
59 2100253 Knob, 1/4” Shaft, Push on 2
60 2100334 Thrust Strip 4
61 2100197 Clip, Steel Cable 1
62 2120233 Spacer .252 ID X .5 OD X
.935” LG 4
63 2120259 Spacer .38 OD X .13 THK #8
Screw 2
65 2150185 Sprocket, 25B18, 1/2” Bore 2
66 2150378 Sprocket, 25B20 3/8” Bore 1
67 2150484 Bearing ASsy, Hi-Temp 1 1/8”
OD X 1/2: ID 8
68 2150393 Drive Chain 1
69 304P105* Nut, Hex KEPS #4-40 1
71 206P130* Nut, HEX KEPS #6-32 (Small
Pttrn) 1
73 308P124* Screw, Mach One Way #8-32 1
74 308P243* Nut, Hex Keps #8-32 1
75 308P145* Nut, HEX Acorn #08-32 Low
Crown 1
76 308P199* Nut, HEX KEPS #8-32 1
77 308P203* Screw, Tap 8-32 X 3/8” W
IntTooth Wshr 1
79 308P223* Washer, Flat #8 1
80 308P340* Nut, HEX Acorn Lock #8-32 1
81 310P102* Washer, IntTooth Lock #10 1
82 310P146* Nut, Hex KEPS #10-32 1
83 310P187* Screw Set, #10-32 x 3/8 HEX,
Socket-Cone Point 1
84 310P196* Screw, Shoulder 10-32 SS 1
87 310P204* Fillister Head Phillips Screw
#10-32 x .25 1
88 310P213* Screw, PHPNHD #10-16 X
3/4” THRD Form 1
89 310P214* Screw, HEX #10-32 x 1/2” 1
90 235P109* Screw, HEXCAP 1/4-20 x 1/2” 1
91 325P154* Washer 1/4” Helical Spring
Lock 1
92 325P177* Screw, Shoulder 5/16 SD 1
93 325P192* Screw, HEX head #1/4-20 x
1.275” SS 1
94 4000186 Motor, 230 V 1
95 7000913 Replacement Fan Kit 1
96 4010187 Transformer 240 VAC 12 VAC 1
97 4010221 CAP MP Motor Run 1
98 4030352 Thermostat, HiLimit 700 1
99 4939446 Htr, Foil 208V 35W .25 Fe-
male Terminals 1
100 4050214 Thermocouple Type K Open
End 1
101 4050236 Contactor, 2 Pole 1
102 4051010 Relay, Random Phase Solid
State 50A 1
103 4060374 Ground Lug 1
104 4070154 Varistor Board 1
105 4070215 Assy-PCB Wendy’s GST-2H 1
106 5040022 Bottom Gasket 4
108 7000984 Main Belt 1
109 7000991 Crown & Heel Belt 1
110 0022245 Plate Wldmt Line Filter (Mfg.
No. 9210961 only) 1
111 7001428 Line Filter 10 A (Mfg. No.
9210961 only) 1
112 306P130* Nut, Hex Keps #6-32 (Small
Pattern) 9
* Available in Packages of ten (10)

15
P/N 1012011 Rev. C 06/18
20
13
2
18
22
24
16
1
8
8
1
16
22
24
18
23
9
10
17
11
17
25
12
14
21
3
7
5
4
6
15
15
19
26
27
27
Parts List
Item
No.
Part # Description Qty.
1 0013092 Cam Bracket Assy 4
2 0021864 Adjust Frame Wldmt 1
3 0021865 Main Platen Frame Wldmt 1
4 0021953 Weldment, Drive Roller Adjust
Lanes 1
5 0021954 Weldment, Idler Adjust Lanes 1
6 0021976 Wldmt, Drive Roller Main
Platen 1
7 0021977 Wldmt, Idler Roller Main
Platen 1
8 0022004 Slide Plate Wldmt 4
9 0022005 Crown Plate Wldmt 1
10 0022006 Heel Plate Wldmt 1
11
0100298 Platen, Main 230V, 1900W
(Mfg. No. 9210961 only) 1
0100290 Platen, Main 208V, 1900W
(Mfg. No. 9210962 only)
12 0400458 Insulation, Main Platen 1
Item
No.
Part # Description Qty.
13 0506853 Frame Cover 1
14 0507092 Insulation Plate 1
15 0507140 Alum Washer 2
16 0600162 Spring, Cam 8
17 2120233 Spacer .252 Id X .5 Od X
.925” Lg 4
18 2150362 Cam, Hbcs 4
19 2150376 Shaft Crown 1
20 3080144 Screw, #8-32 X 1/4” (#6 Head) 4
21 3080164 Screw, Mach. #8-32 X 1” 4
22 3080340 Nut, Hex Acorn Lock #8-32 8
23 3100187 Screw Set, #10-32 X 3/8 Hex
Socket-Cone Point 4
24 3100215 Scr, Shldr #10-32 X 1/4”
W/1/4” Shldr Precision 8
25 3250193 Screw, Hex Head, #1/4-20 X
1.375”, S.s. 4
26 7000984 Main Belt 1
27 7000991 Crown & Heel Belt 2

16 P/N 1012011 Rev. C 06/18
Wiring Diagram Mfg No. 9210961

17
P/N 1012011 Rev. C 06/18
Wiring Diagram Mfg No. 9210962

18 P/N 1012011 Rev. C 06/18
Notes

Limited Warranty
Equipment manufactured by Antunes has been constructed of the finest materials available and manufactured to high
quality standards. These units are warranted to be free from electrical and mechanical defects for a period of eighteen
(18) month from date of purchase under normal use and service, and when installed in accordance with manufacturer’s
recommendations. To insure continued operation of the units, follow the maintenance procedures outlined in the Owner’s
Manual. During the first 18 months, electro-mechanical parts, non-overtime labor, and travel expenses up to 2 hours (100
miles/160 km), round trip from the nearest Authorized Service Center are covered.
This warranty does not cover cost of installation, defects caused by improper storage or handling prior to placing of the
Equipment. This warranty does not cover overtime charges or work done by unauthorized service agencies or personnel.
This warranty does not cover normal maintenance, calibration, or regular adjustments as specified in operating and main-
tenance instructions of this manual, and/or labor involved in moving adjacent objects to gain access to the equipment.
This warranty does not cover consumable/wear items. This warranty does not cover damage to the Load Cell or Load
Cell Assembly due to abuse, misuse, dropping of unit/shock loads or exceeding maximum weight capacity (4 lbs). This
warranty does not cover water contamination problems such as foreign material in water lines or inside solenoid valves. It
does not cover water pressure problems or failures resulting from improper/incorrect voltage supply. This warranty does
not cover Travel Time & Mileage in excess of 2 hours (100 miles/160 km) round trip from the nearest authorized service
agency.
Antunes reserves the right to make changes in design or add any improvements on any product. The right is always
reserved to modify equipment because of factors beyond our control and government regulations. Changes to update
equipment do not constitute a warranty charge.
If shipment is damaged in transit, the purchaser should make a claim directly upon the carrier. Careful inspection should
be made of the shipment as soon as it arrives and visible damage should be noted upon the carrier’s receipt. Damage
should be reported to the carrier. This damage is not covered under this warranty.
Warranty charges do not include freight or foreign, excise, municipal or other sales or use taxes. All such freight and
taxes are the responsibility of the purchaser.
This warranty is exclusive and is in lieu of all other warranties, expressed or implied, including any implied warranty or
merchantability or fitness for a particular purpose, each of which is hereby expressly disclaimed. The remedies described
above are exclusive and in no event shall ANTUNES be liable for special consequential or incidental damages for the
breach or delay in performance of this warranty.
The warranty does not extend to:
yDamages caused in shipment or damage as result of improper use.
yInstallation of electrical service.
yInstallation, calibration, or adjustment.
yNormal maintenance outlined in this manual.
yMalfunction resulting from improper service or maintenance.
yDamage caused by improper installation, abuse, or careless handling.
yDamage from moisture getting into electrical components.
yDamage from tampering with, removal of, or changing any preset control or safety device.
yDamage caused by parts or components not provided by Antunes
[phone]
[phone]
[phone]
[phone]
[phone]