AnyTone AT-779UV User manual

1
24
V/M
VOL
FUN
MAIN
MON
MIC
779UV
MIC
PPT
2
1
3
4
789
ABCD
560
SQL
TONE
SCAN
BLK REV
TOT
FUN
V/M
MAIN
DIL
SUB RPT LAM
POW
SKIP MON
V/M
VOL
FUN
MAIN
MON
MIC
779UV
PTT
MIC
MIC
PPT
2
1
3
4
789
ABCD
560
SQL
TONE
SCAN
BLK REV
TOT
FUN
V/M
MAIN
DIL
SUB RPT LAM
POW
SKIP MON
【UP】/【DN】 /
【UP】
【UP】/【DN】
/
»
779UV
V/M
FUN
MAIN
MON
VOL
2
1
3
4
789
ABCD
560
SQL
TONE
SCAN
BLK REV
TOT
FUN
V/M
MAIN
DIL
SUBRPTLAM
POW
SKIPMON
PPT
MIC
Instruction Manual
AT-779UV
1. WARNING
Transceiver
Screws
Microphone
Pads
Mobile Bracket
non-slip mat Fuse(10A 250V)
Adjusting screws
manual
2. ACCESSORIES
2.1 Standard Accessories
3. GETTING ACQUAINTED
3.1 Front panel
3.2 Rear panel
3.3 Microphone
VFO/Channel mode switch
Main channelLCD Up
Down Indicator
Power on, volume switch
Menu
Monitor
Programming port/ microphone jack
Antenna jack External speaker jack
Up /Down key
Indicator
Number key
4. BASIC OPERATIONS
4.1 Switching the Power On/Off
1. Turn the Volume knob clockwise to turn on the radio, the radio LCD will display
2. Power Off: Turn volume knob anti-clockwise until hear "click" to turn off the radio.
programmed text and emit a beep sound .
4.2 Adjusting the Volume
Turn volume knob clockwise to increase colume and anti-clockwise to reduce it.
4.3 Switch between Main Channel and Sub Channel
In standby states, press the microphpne key or front panel key to switch
between main channel and sub channel. The top left corner of LCD will display current
main channel .
4.4 Adjust Channel
1. Press microphone key or front panel key to switch the radio to channel mode,
press microphone key or front panel key to choose channel .
2. In channel mode, input three numbers by number key to fast choose a channel.
4.5 Adjusting Frequency
1. By number key: In VFO mode, you can input wanted frequency by the microphone
number key. For example if want 145.125Mhz, just press key 1, 4, 5, 1, 2, 5, if want
145Mhz, just press 1, 4, 5. The input is invalid if the frequency is over range.
2. By step size: In VFO mode, press microphone or front panel
【UP】/【DN】
key can change frequency by step size.
Step size can be programmed by software from 2.5K to 50K.
4.5 Store channel
In standby states, press the microphpne key , the top left corner will display Func ,
then press KEY , the LCD bottom left corner will display Save to XXX,
now press key to choose a channel number, hold key to store the
new frequency and return to standby.
XXX stands for the channel number, if LCD displays “Null” under “Save TO XXX”,
means current channel is empty.
3
Qixiang Electon Science &
Technoloyg Co.,Ltd.
www.qxdz.cn
【UP】/【DN】
【# LAM】
4.6 Channel Delete
1. In channel mode, press microphone key, then press key, the LCD displays
“Delete XXX” and frequency, presss key to choose the channel to delete,
【DN】
hold key delelte to current channel.
»
“XXX” stands for the channel number, the LCD displays “Null” after chennel deleted
(Europe version only)
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition
that this device does not cause harmful interference.
GMRS Frequency List:
cm away from the body of the user. Warning statement to the user for keeping at least 71.372cm
separation distance and the prohibition of operating to a person has been printed on the user’s manual.
Ω
cm between the radiator & body.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment shall be installed and operated with minimum distance 71.372
For a transmitter that can only be operated with an FCC license,warningss concerning
compliance with applicable licensing requirements and information concerning license
applianction procedures.
Note: To get the best range from the external whip antenna(50 )should be used.
Ant:Tx GMRS, Rx:136-174&400-490Mhz, 0dBi . installation is height < 3m.

1
24
V/M
VOL
FUN
MAIN
MON
MIC
779UV
MIC
PPT
2
1
3
4
789
ABCD
560
SQL
TONE
SCAN
BLK REV
TOT
FUN
V/M
MAIN
DIL
SUB RPT LAM
POW
SKIP MON
V/M
VOL
FUN
MAIN
MON
MIC
779UV
PTT
MIC
MIC
PPT
2
1
3
4
789
ABCD
560
SQL
TONE
SCAN
BLK REV
TOT
FUN
V/M
MAIN
DIL
SUB RPT LAM
POW
SKIP MON
【UP】/【DN】 /
【UP】
【UP】/【DN】
/
»
779UV
V/M
FUN
MAIN
MON
VOL
2
1
3
4
789
ABCD
560
SQL
TONE
SCAN
BLK REV
TOT
FUN
V/M
MAIN
DIL
SUBRPTLAM
POW
SKIPMON
PPT
MIC
Instruction Manual
AT-779UV
1. WARNING
Transceiver
Screws
Microphone
Pads
Mobile Bracket
non-slip mat Fuse(10A 250V)
Adjusting screws
manual
2. ACCESSORIES
2.1 Standard Accessories
3. GETTING ACQUAINTED
3.1 Front panel
3.2 Rear panel
3.3 Microphone
VFO/Channel mode switch
Main channelLCD Up
Down Indicator
Power on, volume switch
Menu
Monitor
Programming port/ microphone jack
Antenna jack External speaker jack
Up /Down key
Indicator
Number key
4. BASIC OPERATIONS
4.1 Switching the Power On/Off
1. Turn the Volume knob clockwise to turn on the radio, the radio LCD will display
2. Power Off: Turn volume knob anti-clockwise until hear "click" to turn off the radio.
programmed text and emit a beep sound .
4.2 Adjusting the Volume
Turn volume knob clockwise to increase colume and anti-clockwise to reduce it.
4.3 Switch between Main Channel and Sub Channel
In standby states, press the microphpne key or front panel key to switch
between main channel and sub channel. The top left corner of LCD will display current
main channel .
4.4 Adjust Channel
1. Press microphone key or front panel key to switch the radio to channel mode,
press microphone key or front panel key to choose channel .
2. In channel mode, input three numbers by number key to fast choose a channel.
4.5 Adjusting Frequency
1. By number key: In VFO mode, you can input wanted frequency by the microphone
number key. For example if want 145.125Mhz, just press key 1, 4, 5, 1, 2, 5, if want
145Mhz, just press 1, 4, 5. The input is invalid if the frequency is over range.
2. By step size: In VFO mode, press microphone or front panel
【UP】/【DN】
key can change frequency by step size.
Step size can be programmed by software from 2.5K to 50K.
4.5 Store channel
In standby states, press the microphpne key , the top left corner will display Func ,
then press KEY , the LCD bottom left corner will display Save to XXX,
now press key to choose a channel number, hold key to store the
new frequency and return to standby.
XXX stands for the channel number, if LCD displays “Null” under “Save TO XXX”,
means current channel is empty.
3
Qixiang Electon Science &
Technoloyg Co.,Ltd.
www.qxdz.cn
【UP】/【DN】
【# LAM】
4.6 Channel Delete
1. In channel mode, press microphone key, then press key, the LCD displays
“Delete XXX” and frequency, presss key to choose the channel to delete,
【DN】
hold key delelte to current channel.
»
“XXX” stands for the channel number, the LCD displays “Null” after chennel deleted
(Europe version only)
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition
that this device does not cause harmful interference.
GMRS Frequency List:
cm away from the body of the user. Warning statement to the user for keeping at least 71.372cm
separation distance and the prohibition of operating to a person has been printed on the user’s manual.
Ω
cm between the radiator & body.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment shall be installed and operated with minimum distance 71.372
For a transmitter that can only be operated with an FCC license,warningss concerning
compliance with applicable licensing requirements and information concerning license
applianction procedures.
Note: To get the best range from the external whip antenna(50 )should be used.
Ant:Tx GMRS, Rx:136-174&400-490Mhz, 0dBi . installation is height < 3m.

1
24
V/M
VOL
FUN
MAIN
MON
MIC
779UV
MIC
PPT
2
1
3
4
789
ABCD
560
SQL
TONE
SCAN
BLK REV
TOT
FUN
V/M
MAIN
DIL
SUB RPT LAM
POW
SKIP MON
V/M
VOL
FUN
MAIN
MON
MIC
779UV
PTT
MIC
MIC
PPT
2
1
3
4
789
ABCD
560
SQL
TONE
SCAN
BLK REV
TOT
FUN
V/M
MAIN
DIL
SUB RPT LAM
POW
SKIP MON
【UP】/【DN】 /
【UP】
【UP】/【DN】
/
»
779UV
V/M
FUN
MAIN
MON
VOL
2
1
3
4
789
ABCD
560
SQL
TONE
SCAN
BLK REV
TOT
FUN
V/M
MAIN
DIL
SUBRPTLAM
POW
SKIPMON
PPT
MIC
Instruction Manual
AT-779UV
1. WARNING
Transceiver
Screws
Microphone
Pads
Mobile Bracket
non-slip mat Fuse(10A 250V)
Adjusting screws
manual
2. ACCESSORIES
2.1 Standard Accessories
3. GETTING ACQUAINTED
3.1 Front panel
3.2 Rear panel
3.3 Microphone
VFO/Channel mode switch
Main channelLCD Up
Down Indicator
Power on, volume switch
Menu
Monitor
Programming port/ microphone jack
Antenna jack External speaker jack
Up /Down key
Indicator
Number key
4. BASIC OPERATIONS
4.1 Switching the Power On/Off
1. Turn the Volume knob clockwise to turn on the radio, the radio LCD will display
2. Power Off: Turn volume knob anti-clockwise until hear "click" to turn off the radio.
programmed text and emit a beep sound .
4.2 Adjusting the Volume
Turn volume knob clockwise to increase colume and anti-clockwise to reduce it.
4.3 Switch between Main Channel and Sub Channel
In standby states, press the microphpne key or front panel key to switch
between main channel and sub channel. The top left corner of LCD will display current
main channel .
4.4 Adjust Channel
1. Press microphone key or front panel key to switch the radio to channel mode,
press microphone key or front panel key to choose channel .
2. In channel mode, input three numbers by number key to fast choose a channel.
4.5 Adjusting Frequency
1. By number key: In VFO mode, you can input wanted frequency by the microphone
number key. For example if want 145.125Mhz, just press key 1, 4, 5, 1, 2, 5, if want
145Mhz, just press 1, 4, 5. The input is invalid if the frequency is over range.
2. By step size: In VFO mode, press microphone or front panel
【UP】/【DN】
key can change frequency by step size.
Step size can be programmed by software from 2.5K to 50K.
4.5 Store channel
In standby states, press the microphpne key , the top left corner will display Func ,
then press KEY , the LCD bottom left corner will display Save to XXX,
now press key to choose a channel number, hold key to store the
new frequency and return to standby.
XXX stands for the channel number, if LCD displays “Null” under “Save TO XXX”,
means current channel is empty.
3
Qixiang Electon Science &
Technoloyg Co.,Ltd.
www.qxdz.cn
【UP】/【DN】
【# LAM】
4.6 Channel Delete
1. In channel mode, press microphone key, then press key, the LCD displays
“Delete XXX” and frequency, presss key to choose the channel to delete,
【DN】
hold key delelte to current channel.
»
“XXX” stands for the channel number, the LCD displays “Null” after chennel deleted
(Europe version only)
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition
that this device does not cause harmful interference.
GMRS Frequency List:
cm away from the body of the user. Warning statement to the user for keeping at least 71.372cm
separation distance and the prohibition of operating to a person has been printed on the user’s manual.
Ω
cm between the radiator & body.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment shall be installed and operated with minimum distance 71.372
For a transmitter that can only be operated with an FCC license,warningss concerning
compliance with applicable licensing requirements and information concerning license
applianction procedures.
Note: To get the best range from the external whip antenna(50 )should be used.
Ant:Tx GMRS, Rx:136-174&400-490Mhz, 0dBi . installation is height < 3m.

1
24
V/M
VOL
FUN
MAIN
MON
MIC
779UV
MIC
PPT
2
1
3
4
789
ABCD
560
SQL
TONE
SCAN
BLK REV
TOT
FUN
V/M
MAIN
DIL
SUB RPT LAM
POW
SKIP MON
V/M
VOL
FUN
MAIN
MON
MIC
779UV
PTT
MIC
MIC
PPT
2
1
3
4
789
ABCD
560
SQL
TONE
SCAN
BLK REV
TOT
FUN
V/M
MAIN
DIL
SUB RPT LAM
POW
SKIP MON
【UP】/【DN】 /
【UP】
【UP】/【DN】
/
»
779UV
V/M
FUN
MAIN
MON
VOL
2
1
3
4
789
ABCD
560
SQL
TONE
SCAN
BLK REV
TOT
FUN
V/M
MAIN
DIL
SUBRPTLAM
POW
SKIPMON
PPT
MIC
Instruction Manual
AT-779UV
1. WARNING
Transceiver
Screws
Microphone
Pads
Mobile Bracket
non-slip mat Fuse(10A 250V)
Adjusting screws
manual
2. ACCESSORIES
2.1 Standard Accessories
3. GETTING ACQUAINTED
3.1 Front panel
3.2 Rear panel
3.3 Microphone
VFO/Channel mode switch
Main channelLCD Up
Down Indicator
Power on, volume switch
Menu
Monitor
Programming port/ microphone jack
Antenna jack External speaker jack
Up /Down key
Indicator
Number key
4. BASIC OPERATIONS
4.1 Switching the Power On/Off
1. Turn the Volume knob clockwise to turn on the radio, the radio LCD will display
2. Power Off: Turn volume knob anti-clockwise until hear "click" to turn off the radio.
programmed text and emit a beep sound .
4.2 Adjusting the Volume
Turn volume knob clockwise to increase colume and anti-clockwise to reduce it.
4.3 Switch between Main Channel and Sub Channel
In standby states, press the microphpne key or front panel key to switch
between main channel and sub channel. The top left corner of LCD will display current
main channel .
4.4 Adjust Channel
1. Press microphone key or front panel key to switch the radio to channel mode,
press microphone key or front panel key to choose channel .
2. In channel mode, input three numbers by number key to fast choose a channel.
4.5 Adjusting Frequency
1. By number key: In VFO mode, you can input wanted frequency by the microphone
number key. For example if want 145.125Mhz, just press key 1, 4, 5, 1, 2, 5, if want
145Mhz, just press 1, 4, 5. The input is invalid if the frequency is over range.
2. By step size: In VFO mode, press microphone or front panel
【UP】/【DN】
key can change frequency by step size.
Step size can be programmed by software from 2.5K to 50K.
4.5 Store channel
In standby states, press the microphpne key , the top left corner will display Func ,
then press KEY , the LCD bottom left corner will display Save to XXX,
now press key to choose a channel number, hold key to store the
new frequency and return to standby.
XXX stands for the channel number, if LCD displays “Null” under “Save TO XXX”,
means current channel is empty.
3
Qixiang Electon Science &
Technoloyg Co.,Ltd.
www.qxdz.cn
【UP】/【DN】
【# LAM】
4.6 Channel Delete
1. In channel mode, press microphone key, then press key, the LCD displays
“Delete XXX” and frequency, presss key to choose the channel to delete,
【DN】
hold key delelte to current channel.
»
“XXX” stands for the channel number, the LCD displays “Null” after chennel deleted
(Europe version only)
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition
that this device does not cause harmful interference.
GMRS Frequency List:
cm away from the body of the user. Warning statement to the user for keeping at least 71.372cm
separation distance and the prohibition of operating to a person has been printed on the user’s manual.
Ω
cm between the radiator & body.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment shall be installed and operated with minimum distance 71.372
For a transmitter that can only be operated with an FCC license,warningss concerning
compliance with applicable licensing requirements and information concerning license
applianction procedures.
Note: To get the best range from the external whip antenna(50 )should be used.
Ant:Tx GMRS, Rx:136-174&400-490Mhz, 0dBi . installation is height < 3m.

1
24
V/M
VOL
FUN
MAIN
MON
MIC
779UV
MIC
PPT
2
1
3
4
789
ABCD
560
SQL
TONE
SCAN
BLK REV
TOT
FUN
V/M
MAIN
DIL
SUB RPT LAM
POW
SKIP MON
V/M
VOL
FUN
MAIN
MON
MIC
779UV
PTT
MIC
MIC
PPT
2
1
3
4
789
ABCD
560
SQL
TONE
SCAN
BLK REV
TOT
FUN
V/M
MAIN
DIL
SUB RPT LAM
POW
SKIP MON
【UP】/【DN】 /
【UP】
【UP】/【DN】
/
»
779UV
V/M
FUN
MAIN
MON
VOL
2
1
3
4
789
ABCD
560
SQL
TONE
SCAN
BLK REV
TOT
FUN
V/M
MAIN
DIL
SUBRPTLAM
POW
SKIPMON
PPT
MIC
Instruction Manual
AT-779UV
1. WARNING
Transceiver
Screws
Microphone
Pads
Mobile Bracket
non-slip mat Fuse(10A 250V)
Adjusting screws
manual
2. ACCESSORIES
2.1 Standard Accessories
3. GETTING ACQUAINTED
3.1 Front panel
3.2 Rear panel
3.3 Microphone
VFO/Channel mode switch
Main channelLCD Up
Down Indicator
Power on, volume switch
Menu
Monitor
Programming port/ microphone jack
Antenna jack External speaker jack
Up /Down key
Indicator
Number key
4. BASIC OPERATIONS
4.1 Switching the Power On/Off
1. Turn the Volume knob clockwise to turn on the radio, the radio LCD will display
2. Power Off: Turn volume knob anti-clockwise until hear "click" to turn off the radio.
programmed text and emit a beep sound .
4.2 Adjusting the Volume
Turn volume knob clockwise to increase colume and anti-clockwise to reduce it.
4.3 Switch between Main Channel and Sub Channel
In standby states, press the microphpne key or front panel key to switch
between main channel and sub channel. The top left corner of LCD will display current
main channel .
4.4 Adjust Channel
1. Press microphone key or front panel key to switch the radio to channel mode,
press microphone key or front panel key to choose channel .
2. In channel mode, input three numbers by number key to fast choose a channel.
4.5 Adjusting Frequency
1. By number key: In VFO mode, you can input wanted frequency by the microphone
number key. For example if want 145.125Mhz, just press key 1, 4, 5, 1, 2, 5, if want
145Mhz, just press 1, 4, 5. The input is invalid if the frequency is over range.
2. By step size: In VFO mode, press microphone or front panel
【UP】/【DN】
key can change frequency by step size.
Step size can be programmed by software from 2.5K to 50K.
4.5 Store channel
In standby states, press the microphpne key , the top left corner will display Func ,
then press KEY , the LCD bottom left corner will display Save to XXX,
now press key to choose a channel number, hold key to store the
new frequency and return to standby.
XXX stands for the channel number, if LCD displays “Null” under “Save TO XXX”,
means current channel is empty.
3
Qixiang Electon Science &
Technoloyg Co.,Ltd.
www.qxdz.cn
【UP】/【DN】
【# LAM】
4.6 Channel Delete
1. In channel mode, press microphone key, then press key, the LCD displays
“Delete XXX” and frequency, presss key to choose the channel to delete,
【DN】
hold key delelte to current channel.
»
“XXX” stands for the channel number, the LCD displays “Null” after chennel deleted
(Europe version only)
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition
that this device does not cause harmful interference.
GMRS Frequency List:
cm away from the body of the user. Warning statement to the user for keeping at least 71.372cm
separation distance and the prohibition of operating to a person has been printed on the user’s manual.
Ω
cm between the radiator & body.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment shall be installed and operated with minimum distance 71.372
For a transmitter that can only be operated with an FCC license,warningss concerning
compliance with applicable licensing requirements and information concerning license
applianction procedures.
Note: To get the best range from the external whip antenna(50 )should be used.
Ant:Tx GMRS, Rx:136-174&400-490Mhz, 0dBi . installation is height < 3m.

/
【UP】/【DN】
【UP】/【DN】
【PTT】
»
»
5
1 +
2 +
3 +
4 +
5 +
6 +
7 +
8 +
9 +
10 +
11 +
12 +
13 +
1 67Hz~254.1Hz、000N~777I
2 67Hz~254.1Hz、000N~777I
3 67Hz~254.1Hz、000N~777I
4 OFF、DTMF、2Tone、5Tone
5 SQ、CT/DCS、Tone、C&T、C/T
6 2.5K~50K
7 WIDE（25K）、NARROW（12.5K）
8 ON、OFF
9 ON、OFF
10 0~70MHz
11 OFF、REPEATER、BUSY
12 0~z
13 ON、OFF
14 1~11、edit、OFF
15 ON、OFF
16
1~100,
17
1~32,
18
FREQ、VOLT、OFF
19
ON、OFF
20
1~30Min、OFF
21
50ms~500ms
22
OFF、1~9
23
5ST、10ST、15ST、2SP
24
1~5
25
1750Hz、2100Hz、1000Hz、1450Hz
26
FREQ、CH、NAME
27
FACTORY？ INITIALIZE？
144-146MHz , 430-440MHz
2.5KHz,5KHz,6.25KHz,10KHz,12.5KHz,15KHz,20
KHz,25KHz,30KHz,50KHz
DC 13.8V±15%
CTCSS/DCS/5Tone/2Tone/DTMF
±2.5ppm
-20℃ ~ +60℃
124x101x36mm
0.45kg
≤0.25μV ≤0.35μV
≥70dB ≥60dB
+1~-3dB(0.3~3KHz) +1~-3dB(0.3~2.55KHz)
≥45dB ≥40dB
<3%
>2W@10%
VHF: 25/5W, UHF: 20/5W
16KΦF3E 11KΦF3E
≥70dB ≥60dB
≥40dB ≥36dB
≥60dB ≥60dB
+1~-3dB(0.3~3KHz) +1~-3dB(0.3~2.55KHz)
≤5%
4.7 Receiving
4.8 Transmitting
Choose a receiving channel or frequency for receiving call, if the RX signal is week,
Hold [PTT] and speak into microphone. the radio start transmit, the screen shows red
TX and eld strength. Hold the microphone approximately 2.5-5.0cm from your lips and
speak to microphone in your normal speaking voice to get best timbre.
When the RX icon and eld strength ashes, but can not hear the calling, it means
current channel receive a matching carrier but unmatching signaling. Refer to
CTCSS/ DCS CODE or Optional Signaling setup in Page 6).
hold front panel key or microphone key to monitor weak signal.
4.9 Emergency Alarm
In standby, hold key, release it until the LCD displays ALARM, the alarm function
turns on. Program emergency alarm rule shall be programmed by PC software.
4.10 Keypad Lockout
In standby, hold key or key , the radio emit Du sound, the LCD displays LOCK.
Now release the key , the keypad is locked. To turn of key lock, hold key or key until
the radio emit Du Du, the LOCK icon disappear. now release the key.
4.11 Transmit Tone Pulse Frequency
Hold PTT and [DN] key will transmit selected Pre-programmed tone pulse frequency.
4.12 VFO Scan and Channel Scan
1. VFO scan: In VFO mode, press microphone key or key to start VFO scan . if the
radio has programm PL1, PH1, ,PL2, PH2, PH2 frequency( in the buttom of channel list), VFO
scan will between PL1-PL2 and PL2-PH2.
2. Channel Scan: In channel mode press microphone key and then press key to start
channel scan. Channel scan setting shall be programmed by PC software.
4. BASIC OPERATIONS 4. SHORTCUT OPERATION
Press microphone key and then press number key TO fast enter following functions,
then press key to choose value. presss key or key to Store.
No. Function name Combination Key
Squelch level setting
Optional signaling setting
Scan Skip
Scan
Busy channel lockout
Frequency reverse
Time out timer
Sub channel on/off switch
Offset direction
Function Menu
Power setting.
LCD brightless
DTMF Code check
When check DTMF code, press PTT will send current DTMF code.
To revise DTMF code, press key and then press key to enter edit mode.
In DTMF check mode
input DTMF code by number keys , then press PTT to transmit the code and store.
5. FUNCTION SETTING
5.1 By Front Panel Key
1. Press key to enter main menu.
2. Press key or key to choose function.
Press key to choose value.
3.
4. Press key or key to store and exit.
When setting DCS code, key is for switch between positive and inverse code.
»
5.2 By Microphone Key
1. Press key and then press key to enter menu.
2. Press key or key to choose function.
Press key to choose value.
3.
4. Press key to store and exit
When setting DCS code, key is for switch between Positive and inverse code.
key is for choose special DCS.
Function list
Function list
No. Function name Setting value
TX CTC/DCS
RX CTC/DCS
TX/RX CTC/DCS
Optional signaling
Squelch mode
Step size
Band width
Reverse
Talk around
Offset frequency
5. FUNCTION SETTING
No. Function name Value
Busy channel Lock
Channel name
TX OFF
Scramber
Compander
Sub channel display
Key beep
Time out timer
DMTF transmit time
Squelch level
Scan pause time
LCD brightness
Tone burst frequency
Channel display
Reset
Press PTT to transmit
Press PTT to transmit
5Tone
2Tone
67 8 
6. SPECIFICAITONS

GENERAL
Frequency Range
Channel Spacing
Phase-locked Step
Operating Voltage
Squelch
Frequency Stability
Operating Temperature
Dimensions(mm)
Weight (main unit)
Carrier/
25K (Wide Band) 12.5K (Narrow band)
TRANSMITTER
RECEIVER
Wide band Narrow band
Wide band Narrow band
Power Output
Modulation
Adjacent Channel Powe
Hum & Noise
Spurious Emission
Audio Response
Audio Distortion
Sensitivity (12dB Sinad)
Adjacent Channel
Selectivity
Audio Response
Hum & Noise
Audio distortion
Audio power output
6
»
28
ON、OFF
NC(Noise reduction)
4.13 FM radio
Press microphone key or front panel key to switch the radio to channel mode,
Input FM radio frequency directly by the microphone number keys.
Europe version:
467.55-467.725MHz
12.5K
Europe version:
USA version:
USA version: 462.5625-462.725MHz
136-174MHz , 400-490MHz
RX:
TX/RX:
TX/RX:
TX/RX:

/
【UP】/【DN】
【UP】/【DN】
【PTT】
»
»
5
1 +
2 +
3 +
4 +
5 +
6 +
7 +
8 +
9 +
10 +
11 +
12 +
13 +
1 67Hz~254.1Hz、000N~777I
2 67Hz~254.1Hz、000N~777I
3 67Hz~254.1Hz、000N~777I
4 OFF、DTMF、2Tone、5Tone
5 SQ、CT/DCS、Tone、C&T、C/T
6 2.5K~50K
7 WIDE（25K）、NARROW（12.5K）
8 ON、OFF
9 ON、OFF
10 0~70MHz
11 OFF、REPEATER、BUSY
12 0~z
13 ON、OFF
14 1~11、edit、OFF
15 ON、OFF
16
1~100,
17
1~32,
18
FREQ、VOLT、OFF
19
ON、OFF
20
1~30Min、OFF
21
50ms~500ms
22
OFF、1~9
23
5ST、10ST、15ST、2SP
24
1~5
25
1750Hz、2100Hz、1000Hz、1450Hz
26
FREQ、CH、NAME
27
FACTORY？ INITIALIZE？
144-146MHz , 430-440MHz
2.5KHz,5KHz,6.25KHz,10KHz,12.5KHz,15KHz,20
KHz,25KHz,30KHz,50KHz
DC 13.8V±15%
CTCSS/DCS/5Tone/2Tone/DTMF
±2.5ppm
-20℃ ~ +60℃
124x101x36mm
0.45kg
≤0.25μV ≤0.35μV
≥70dB ≥60dB
+1~-3dB(0.3~3KHz) +1~-3dB(0.3~2.55KHz)
≥45dB ≥40dB
<3%
>2W@10%
VHF: 25/5W, UHF: 20/5W
16KΦF3E 11KΦF3E
≥70dB ≥60dB
≥40dB ≥36dB
≥60dB ≥60dB
+1~-3dB(0.3~3KHz) +1~-3dB(0.3~2.55KHz)
≤5%
4.7 Receiving
4.8 Transmitting
Choose a receiving channel or frequency for receiving call, if the RX signal is week,
Hold [PTT] and speak into microphone. the radio start transmit, the screen shows red
TX and eld strength. Hold the microphone approximately 2.5-5.0cm from your lips and
speak to microphone in your normal speaking voice to get best timbre.
When the RX icon and eld strength ashes, but can not hear the calling, it means
current channel receive a matching carrier but unmatching signaling. Refer to
CTCSS/ DCS CODE or Optional Signaling setup in Page 6).
hold front panel key or microphone key to monitor weak signal.
4.9 Emergency Alarm
In standby, hold key, release it until the LCD displays ALARM, the alarm function
turns on. Program emergency alarm rule shall be programmed by PC software.
4.10 Keypad Lockout
In standby, hold key or key , the radio emit Du sound, the LCD displays LOCK.
Now release the key , the keypad is locked. To turn of key lock, hold key or key until
the radio emit Du Du, the LOCK icon disappear. now release the key.
4.11 Transmit Tone Pulse Frequency
Hold PTT and [DN] key will transmit selected Pre-programmed tone pulse frequency.
4.12 VFO Scan and Channel Scan
1. VFO scan: In VFO mode, press microphone key or key to start VFO scan . if the
radio has programm PL1, PH1, ,PL2, PH2, PH2 frequency( in the buttom of channel list), VFO
scan will between PL1-PL2 and PL2-PH2.
2. Channel Scan: In channel mode press microphone key and then press key to start
channel scan. Channel scan setting shall be programmed by PC software.
4. BASIC OPERATIONS 4. SHORTCUT OPERATION
Press microphone key and then press number key TO fast enter following functions,
then press key to choose value. presss key or key to Store.
No. Function name Combination Key
Squelch level setting
Optional signaling setting
Scan Skip
Scan
Busy channel lockout
Frequency reverse
Time out timer
Sub channel on/off switch
Offset direction
Function Menu
Power setting.
LCD brightless
DTMF Code check
When check DTMF code, press PTT will send current DTMF code.
To revise DTMF code, press key and then press key to enter edit mode.
In DTMF check mode
input DTMF code by number keys , then press PTT to transmit the code and store.
5. FUNCTION SETTING
5.1 By Front Panel Key
1. Press key to enter main menu.
2. Press key or key to choose function.
Press key to choose value.
3.
4. Press key or key to store and exit.
When setting DCS code, key is for switch between positive and inverse code.
»
5.2 By Microphone Key
1. Press key and then press key to enter menu.
2. Press key or key to choose function.
Press key to choose value.
3.
4. Press key to store and exit
When setting DCS code, key is for switch between Positive and inverse code.
key is for choose special DCS.
Function list
Function list
No. Function name Setting value
TX CTC/DCS
RX CTC/DCS
TX/RX CTC/DCS
Optional signaling
Squelch mode
Step size
Band width
Reverse
Talk around
Offset frequency
5. FUNCTION SETTING
No. Function name Value
Busy channel Lock
Channel name
TX OFF
Scramber
Compander
Sub channel display
Key beep
Time out timer
DMTF transmit time
Squelch level
Scan pause time
LCD brightness
Tone burst frequency
Channel display
Reset
Press PTT to transmit
Press PTT to transmit
5Tone
2Tone
67 8 
6. SPECIFICAITONS

GENERAL
Frequency Range
Channel Spacing
Phase-locked Step
Operating Voltage
Squelch
Frequency Stability
Operating Temperature
Dimensions(mm)
Weight (main unit)
Carrier/
25K (Wide Band) 12.5K (Narrow band)
TRANSMITTER
RECEIVER
Wide band Narrow band
Wide band Narrow band
Power Output
Modulation
Adjacent Channel Powe
Hum & Noise
Spurious Emission
Audio Response
Audio Distortion
Sensitivity (12dB Sinad)
Adjacent Channel
Selectivity
Audio Response
Hum & Noise
Audio distortion
Audio power output
6
»
28
ON、OFF
NC(Noise reduction)
4.13 FM radio
Press microphone key or front panel key to switch the radio to channel mode,
Input FM radio frequency directly by the microphone number keys.
Europe version:
467.55-467.725MHz
12.5K
Europe version:
USA version:
USA version: 462.5625-462.725MHz
136-174MHz , 400-490MHz
RX:
TX/RX:
TX/RX:
TX/RX:

/
【UP】/【DN】
【UP】/【DN】
【PTT】
»
»
5
1 +
2 +
3 +
4 +
5 +
6 +
7 +
8 +
9 +
10 +
11 +
12 +
13 +
1 67Hz~254.1Hz、000N~777I
2 67Hz~254.1Hz、000N~777I
3 67Hz~254.1Hz、000N~777I
4 OFF、DTMF、2Tone、5Tone
5 SQ、CT/DCS、Tone、C&T、C/T
6 2.5K~50K
7 WIDE（25K）、NARROW（12.5K）
8 ON、OFF
9 ON、OFF
10 0~70MHz
11 OFF、REPEATER、BUSY
12 0~z
13 ON、OFF
14 1~11、edit、OFF
15 ON、OFF
16
1~100,
17
1~32,
18
FREQ、VOLT、OFF
19
ON、OFF
20
1~30Min、OFF
21
50ms~500ms
22
OFF、1~9
23
5ST、10ST、15ST、2SP
24
1~5
25
1750Hz、2100Hz、1000Hz、1450Hz
26
FREQ、CH、NAME
27
FACTORY？ INITIALIZE？
144-146MHz , 430-440MHz
2.5KHz,5KHz,6.25KHz,10KHz,12.5KHz,15KHz,20
KHz,25KHz,30KHz,50KHz
DC 13.8V±15%
CTCSS/DCS/5Tone/2Tone/DTMF
±2.5ppm
-20℃ ~ +60℃
124x101x36mm
0.45kg
≤0.25μV ≤0.35μV
≥70dB ≥60dB
+1~-3dB(0.3~3KHz) +1~-3dB(0.3~2.55KHz)
≥45dB ≥40dB
<3%
>2W@10%
VHF: 25/5W, UHF: 20/5W
16KΦF3E 11KΦF3E
≥70dB ≥60dB
≥40dB ≥36dB
≥60dB ≥60dB
+1~-3dB(0.3~3KHz) +1~-3dB(0.3~2.55KHz)
≤5%
4.7 Receiving
4.8 Transmitting
Choose a receiving channel or frequency for receiving call, if the RX signal is week,
Hold [PTT] and speak into microphone. the radio start transmit, the screen shows red
TX and eld strength. Hold the microphone approximately 2.5-5.0cm from your lips and
speak to microphone in your normal speaking voice to get best timbre.
When the RX icon and eld strength ashes, but can not hear the calling, it means
current channel receive a matching carrier but unmatching signaling. Refer to
CTCSS/ DCS CODE or Optional Signaling setup in Page 6).
hold front panel key or microphone key to monitor weak signal.
4.9 Emergency Alarm
In standby, hold key, release it until the LCD displays ALARM, the alarm function
turns on. Program emergency alarm rule shall be programmed by PC software.
4.10 Keypad Lockout
In standby, hold key or key , the radio emit Du sound, the LCD displays LOCK.
Now release the key , the keypad is locked. To turn of key lock, hold key or key until
the radio emit Du Du, the LOCK icon disappear. now release the key.
4.11 Transmit Tone Pulse Frequency
Hold PTT and [DN] key will transmit selected Pre-programmed tone pulse frequency.
4.12 VFO Scan and Channel Scan
1. VFO scan: In VFO mode, press microphone key or key to start VFO scan . if the
radio has programm PL1, PH1, ,PL2, PH2, PH2 frequency( in the buttom of channel list), VFO
scan will between PL1-PL2 and PL2-PH2.
2. Channel Scan: In channel mode press microphone key and then press key to start
channel scan. Channel scan setting shall be programmed by PC software.
4. BASIC OPERATIONS 4. SHORTCUT OPERATION
Press microphone key and then press number key TO fast enter following functions,
then press key to choose value. presss key or key to Store.
No. Function name Combination Key
Squelch level setting
Optional signaling setting
Scan Skip
Scan
Busy channel lockout
Frequency reverse
Time out timer
Sub channel on/off switch
Offset direction
Function Menu
Power setting.
LCD brightless
DTMF Code check
When check DTMF code, press PTT will send current DTMF code.
To revise DTMF code, press key and then press key to enter edit mode.
In DTMF check mode
input DTMF code by number keys , then press PTT to transmit the code and store.
5. FUNCTION SETTING
5.1 By Front Panel Key
1. Press key to enter main menu.
2. Press key or key to choose function.
Press key to choose value.
3.
4. Press key or key to store and exit.
When setting DCS code, key is for switch between positive and inverse code.
»
5.2 By Microphone Key
1. Press key and then press key to enter menu.
2. Press key or key to choose function.
Press key to choose value.
3.
4. Press key to store and exit
When setting DCS code, key is for switch between Positive and inverse code.
key is for choose special DCS.
Function list
Function list
No. Function name Setting value
TX CTC/DCS
RX CTC/DCS
TX/RX CTC/DCS
Optional signaling
Squelch mode
Step size
Band width
Reverse
Talk around
Offset frequency
5. FUNCTION SETTING
No. Function name Value
Busy channel Lock
Channel name
TX OFF
Scramber
Compander
Sub channel display
Key beep
Time out timer
DMTF transmit time
Squelch level
Scan pause time
LCD brightness
Tone burst frequency
Channel display
Reset
Press PTT to transmit
Press PTT to transmit
5Tone
2Tone
67 8 
6. SPECIFICAITONS

GENERAL
Frequency Range
Channel Spacing
Phase-locked Step
Operating Voltage
Squelch
Frequency Stability
Operating Temperature
Dimensions(mm)
Weight (main unit)
Carrier/
25K (Wide Band) 12.5K (Narrow band)
TRANSMITTER
RECEIVER
Wide band Narrow band
Wide band Narrow band
Power Output
Modulation
Adjacent Channel Powe
Hum & Noise
Spurious Emission
Audio Response
Audio Distortion
Sensitivity (12dB Sinad)
Adjacent Channel
Selectivity
Audio Response
Hum & Noise
Audio distortion
Audio power output
6
»
28
ON、OFF
NC(Noise reduction)
4.13 FM radio
Press microphone key or front panel key to switch the radio to channel mode,
Input FM radio frequency directly by the microphone number keys.
Europe version:
467.55-467.725MHz
12.5K
Europe version:
USA version:
USA version: 462.5625-462.725MHz
136-174MHz , 400-490MHz
RX:
TX/RX:
TX/RX:
TX/RX:

/
【UP】/【DN】
【UP】/【DN】
【PTT】
»
»
5
1 +
2 +
3 +
4 +
5 +
6 +
7 +
8 +
9 +
10 +
11 +
12 +
13 +
1 67Hz~254.1Hz、000N~777I
2 67Hz~254.1Hz、000N~777I
3 67Hz~254.1Hz、000N~777I
4 OFF、DTMF、2Tone、5Tone
5 SQ、CT/DCS、Tone、C&T、C/T
6 2.5K~50K
7 WIDE（25K）、NARROW（12.5K）
8 ON、OFF
9 ON、OFF
10 0~70MHz
11 OFF、REPEATER、BUSY
12 0~z
13 ON、OFF
14 1~11、edit、OFF
15 ON、OFF
16
1~100,
17
1~32,
18
FREQ、VOLT、OFF
19
ON、OFF
20
1~30Min、OFF
21
50ms~500ms
22
OFF、1~9
23
5ST、10ST、15ST、2SP
24
1~5
25
1750Hz、2100Hz、1000Hz、1450Hz
26
FREQ、CH、NAME
27
FACTORY？ INITIALIZE？
144-146MHz , 430-440MHz
2.5KHz,5KHz,6.25KHz,10KHz,12.5KHz,15KHz,20
KHz,25KHz,30KHz,50KHz
DC 13.8V±15%
CTCSS/DCS/5Tone/2Tone/DTMF
±2.5ppm
-20℃ ~ +60℃
124x101x36mm
0.45kg
≤0.25μV ≤0.35μV
≥70dB ≥60dB
+1~-3dB(0.3~3KHz) +1~-3dB(0.3~2.55KHz)
≥45dB ≥40dB
<3%
>2W@10%
VHF: 25/5W, UHF: 20/5W
16KΦF3E 11KΦF3E
≥70dB ≥60dB
≥40dB ≥36dB
≥60dB ≥60dB
+1~-3dB(0.3~3KHz) +1~-3dB(0.3~2.55KHz)
≤5%
4.7 Receiving
4.8 Transmitting
Choose a receiving channel or frequency for receiving call, if the RX signal is week,
Hold [PTT] and speak into microphone. the radio start transmit, the screen shows red
TX and eld strength. Hold the microphone approximately 2.5-5.0cm from your lips and
speak to microphone in your normal speaking voice to get best timbre.
When the RX icon and eld strength ashes, but can not hear the calling, it means
current channel receive a matching carrier but unmatching signaling. Refer to
CTCSS/ DCS CODE or Optional Signaling setup in Page 6).
hold front panel key or microphone key to monitor weak signal.
4.9 Emergency Alarm
In standby, hold key, release it until the LCD displays ALARM, the alarm function
turns on. Program emergency alarm rule shall be programmed by PC software.
4.10 Keypad Lockout
In standby, hold key or key , the radio emit Du sound, the LCD displays LOCK.
Now release the key , the keypad is locked. To turn of key lock, hold key or key until
the radio emit Du Du, the LOCK icon disappear. now release the key.
4.11 Transmit Tone Pulse Frequency
Hold PTT and [DN] key will transmit selected Pre-programmed tone pulse frequency.
4.12 VFO Scan and Channel Scan
1. VFO scan: In VFO mode, press microphone key or key to start VFO scan . if the
radio has programm PL1, PH1, ,PL2, PH2, PH2 frequency( in the buttom of channel list), VFO
scan will between PL1-PL2 and PL2-PH2.
2. Channel Scan: In channel mode press microphone key and then press key to start
channel scan. Channel scan setting shall be programmed by PC software.
4. BASIC OPERATIONS 4. SHORTCUT OPERATION
Press microphone key and then press number key TO fast enter following functions,
then press key to choose value. presss key or key to Store.
No. Function name Combination Key
Squelch level setting
Optional signaling setting
Scan Skip
Scan
Busy channel lockout
Frequency reverse
Time out timer
Sub channel on/off switch
Offset direction
Function Menu
Power setting.
LCD brightless
DTMF Code check
When check DTMF code, press PTT will send current DTMF code.
To revise DTMF code, press key and then press key to enter edit mode.
In DTMF check mode
input DTMF code by number keys , then press PTT to transmit the code and store.
5. FUNCTION SETTING
5.1 By Front Panel Key
1. Press key to enter main menu.
2. Press key or key to choose function.
Press key to choose value.
3.
4. Press key or key to store and exit.
When setting DCS code, key is for switch between positive and inverse code.
»
5.2 By Microphone Key
1. Press key and then press key to enter menu.
2. Press key or key to choose function.
Press key to choose value.
3.
4. Press key to store and exit
When setting DCS code, key is for switch between Positive and inverse code.
key is for choose special DCS.
Function list
Function list
No. Function name Setting value
TX CTC/DCS
RX CTC/DCS
TX/RX CTC/DCS
Optional signaling
Squelch mode
Step size
Band width
Reverse
Talk around
Offset frequency
5. FUNCTION SETTING
No. Function name Value
Busy channel Lock
Channel name
TX OFF
Scramber
Compander
Sub channel display
Key beep
Time out timer
DMTF transmit time
Squelch level
Scan pause time
LCD brightness
Tone burst frequency
Channel display
Reset
Press PTT to transmit
Press PTT to transmit
5Tone
2Tone
67 8 
6. SPECIFICAITONS

GENERAL
Frequency Range
Channel Spacing
Phase-locked Step
Operating Voltage
Squelch
Frequency Stability
Operating Temperature
Dimensions(mm)
Weight (main unit)
Carrier/
25K (Wide Band) 12.5K (Narrow band)
TRANSMITTER
RECEIVER
Wide band Narrow band
Wide band Narrow band
Power Output
Modulation
Adjacent Channel Powe
Hum & Noise
Spurious Emission
Audio Response
Audio Distortion
Sensitivity (12dB Sinad)
Adjacent Channel
Selectivity
Audio Response
Hum & Noise
Audio distortion
Audio power output
6
»
28
ON、OFF
NC(Noise reduction)
4.13 FM radio
Press microphone key or front panel key to switch the radio to channel mode,
Input FM radio frequency directly by the microphone number keys.
Europe version:
467.55-467.725MHz
12.5K
Europe version:
USA version:
USA version: 462.5625-462.725MHz
136-174MHz , 400-490MHz
RX:
TX/RX:
TX/RX:
TX/RX:

/
【UP】/【DN】
【UP】/【DN】
【PTT】
»
»
5
1 +
2 +
3 +
4 +
5 +
6 +
7 +
8 +
9 +
10 +
11 +
12 +
13 +
1 67Hz~254.1Hz、000N~777I
2 67Hz~254.1Hz、000N~777I
3 67Hz~254.1Hz、000N~777I
4 OFF、DTMF、2Tone、5Tone
5 SQ、CT/DCS、Tone、C&T、C/T
6 2.5K~50K
7 WIDE（25K）、NARROW（12.5K）
8 ON、OFF
9 ON、OFF
10 0~70MHz
11 OFF、REPEATER、BUSY
12 0~z
13 ON、OFF
14 1~11、edit、OFF
15 ON、OFF
16
1~100,
17
1~32,
18
FREQ、VOLT、OFF
19
ON、OFF
20
1~30Min、OFF
21
50ms~500ms
22
OFF、1~9
23
5ST、10ST、15ST、2SP
24
1~5
25
1750Hz、2100Hz、1000Hz、1450Hz
26
FREQ、CH、NAME
27
FACTORY？ INITIALIZE？
144-146MHz , 430-440MHz
2.5KHz,5KHz,6.25KHz,10KHz,12.5KHz,15KHz,20
KHz,25KHz,30KHz,50KHz
DC 13.8V±15%
CTCSS/DCS/5Tone/2Tone/DTMF
±2.5ppm
-20℃ ~ +60℃
124x101x36mm
0.45kg
≤0.25μV ≤0.35μV
≥70dB ≥60dB
+1~-3dB(0.3~3KHz) +1~-3dB(0.3~2.55KHz)
≥45dB ≥40dB
<3%
>2W@10%
VHF: 25/5W, UHF: 20/5W
16KΦF3E 11KΦF3E
≥70dB ≥60dB
≥40dB ≥36dB
≥60dB ≥60dB
+1~-3dB(0.3~3KHz) +1~-3dB(0.3~2.55KHz)
≤5%
4.7 Receiving
4.8 Transmitting
Choose a receiving channel or frequency for receiving call, if the RX signal is week,
Hold [PTT] and speak into microphone. the radio start transmit, the screen shows red
TX and eld strength. Hold the microphone approximately 2.5-5.0cm from your lips and
speak to microphone in your normal speaking voice to get best timbre.
When the RX icon and eld strength ashes, but can not hear the calling, it means
current channel receive a matching carrier but unmatching signaling. Refer to
CTCSS/ DCS CODE or Optional Signaling setup in Page 6).
hold front panel key or microphone key to monitor weak signal.
4.9 Emergency Alarm
In standby, hold key, release it until the LCD displays ALARM, the alarm function
turns on. Program emergency alarm rule shall be programmed by PC software.
4.10 Keypad Lockout
In standby, hold key or key , the radio emit Du sound, the LCD displays LOCK.
Now release the key , the keypad is locked. To turn of key lock, hold key or key until
the radio emit Du Du, the LOCK icon disappear. now release the key.
4.11 Transmit Tone Pulse Frequency
Hold PTT and [DN] key will transmit selected Pre-programmed tone pulse frequency.
4.12 VFO Scan and Channel Scan
1. VFO scan: In VFO mode, press microphone key or key to start VFO scan . if the
radio has programm PL1, PH1, ,PL2, PH2, PH2 frequency( in the buttom of channel list), VFO
scan will between PL1-PL2 and PL2-PH2.
2. Channel Scan: In channel mode press microphone key and then press key to start
channel scan. Channel scan setting shall be programmed by PC software.
4. BASIC OPERATIONS 4. SHORTCUT OPERATION
Press microphone key and then press number key TO fast enter following functions,
then press key to choose value. presss key or key to Store.
No. Function name Combination Key
Squelch level setting
Optional signaling setting
Scan Skip
Scan
Busy channel lockout
Frequency reverse
Time out timer
Sub channel on/off switch
Offset direction
Function Menu
Power setting.
LCD brightless
DTMF Code check
When check DTMF code, press PTT will send current DTMF code.
To revise DTMF code, press key and then press key to enter edit mode.
In DTMF check mode
input DTMF code by number keys , then press PTT to transmit the code and store.
5. FUNCTION SETTING
5.1 By Front Panel Key
1. Press key to enter main menu.
2. Press key or key to choose function.
Press key to choose value.
3.
4. Press key or key to store and exit.
When setting DCS code, key is for switch between positive and inverse code.
»
5.2 By Microphone Key
1. Press key and then press key to enter menu.
2. Press key or key to choose function.
Press key to choose value.
3.
4. Press key to store and exit
When setting DCS code, key is for switch between Positive and inverse code.
key is for choose special DCS.
Function list
Function list
No. Function name Setting value
TX CTC/DCS
RX CTC/DCS
TX/RX CTC/DCS
Optional signaling
Squelch mode
Step size
Band width
Reverse
Talk around
Offset frequency
5. FUNCTION SETTING
No. Function name Value
Busy channel Lock
Channel name
TX OFF
Scramber
Compander
Sub channel display
Key beep
Time out timer
DMTF transmit time
Squelch level
Scan pause time
LCD brightness
Tone burst frequency
Channel display
Reset
Press PTT to transmit
Press PTT to transmit
5Tone
2Tone
67 8 
6. SPECIFICAITONS

GENERAL
Frequency Range
Channel Spacing
Phase-locked Step
Operating Voltage
Squelch
Frequency Stability
Operating Temperature
Dimensions(mm)
Weight (main unit)
Carrier/
25K (Wide Band) 12.5K (Narrow band)
TRANSMITTER
RECEIVER
Wide band Narrow band
Wide band Narrow band
Power Output
Modulation
Adjacent Channel Powe
Hum & Noise
Spurious Emission
Audio Response
Audio Distortion
Sensitivity (12dB Sinad)
Adjacent Channel
Selectivity
Audio Response
Hum & Noise
Audio distortion
Audio power output
6
»
28
ON、OFF
NC(Noise reduction)
4.13 FM radio
Press microphone key or front panel key to switch the radio to channel mode,
Input FM radio frequency directly by the microphone number keys.
Europe version:
467.55-467.725MHz
12.5K
Europe version:
USA version:
USA version: 462.5625-462.725MHz
136-174MHz , 400-490MHz
RX:
TX/RX:
TX/RX:
TX/RX: