AnyTone MINI CB User manual

KNOW ABOUT THIS RADIO
1Squelch control, SQ, ASQ switch key
2Mode/Scan key
3RF Gain control
4CH9/CH19/Keypad lock
5Power On/Off Volume control
6LCD
7External speaker Jack
8Antenna Jack
MINI CB RADIO
USER MANUAL
163
24
5
8
7

Squelch level control(O.F to 2.8 level available)
ASQ control(A.1-A.9 level available)
Mode control
Short press
1. , until LCD displays SQ and then displays X.X, X.X stands for SQ
level, the bigger value stands for high squelch level.
Short press [
2. UP ] or [ DN ] to change SQ level.
Hold [
3. UP ] or [ DN ] can fast change SQ level.
Hold
4. or wait for 3 seconds to store and exit.
Note：The higher SQ level selected, the stronger signal required to open
speaker and hear the calling.
Hold
1. key, until LCD displays AQ, the ASQ function turned on. The LCD will
displays "A.X", "X" stands for the ASQ level, the bigger value stands for high
squelch level.
Short press microphone [
2. UP ] or [ DN ] to change SQ level
Hold microphone [
3. UP ] or [ DN ] can fast change ASQ level.
Hold
4. or wait for 3 seconds to store and exit.
Note：The higher ASQ level selected, the stronger signal required to open
speaker and hear the calling.
Short press
1. key to switch between AM /FM mode.
The LCD displays the selected mode.
2.
Channel Control
Short press [
1. UP ] or [ DN ] to change working channel.
Hold [
2. UP ] or [ DN ] can fast change working channel.
HOW TO USE THIS RADIO
Power On/Off the radio
Volume control
Turn VOL switch clockwise to power on the radio, the LCD displays the Norms
1.
and then displays channel number.
Turn VOL switch anti-clockwise, until hear Ka Ta, the radio is powered off.
2.
Turn clockwise to increase volume, anti-clockwise to decrease volume.

Note：When RFG function is on the LCD displays R if RFG level is 6 means the
attenuation is 6dBm.
Note：In lock Mode all keys except PTT is valid.
Scan function
RF Gain contro
Emergency Channel
Keypad Lock
Norms control
Install external speaker
Resume factory default
Hold
1. to start scan function, "SC" falshes in the LCD;
Press [
2. UP ] or [ DN ] to change scan direction during scan;
Press
3. or [PTT] key to exit scan function.
Short press
1. key, LCD displays R and the present RF gain level ashes.
Short press microphone [
2. UP ] or [ DN ] to change level.
Short press
3. key to exit RF gain level control.
Short press
1. key to choose CH9, the channel number ashes.
Short press
2. key again to choose CH19, the channel number ashes.
Short press
3. key third time to return to last normal channel.
Hold
1. key for over 2 seconds to lock the keys, LCD displays "LC".
Hold
2. key for over 2 seconds again to unlock the keys, LCD displays OF.
Hold
1. to power on radio, until LCD displays the norms;
Press [
2. UP ] or [ DN ] to choose wanted norms;
Power off and power on again.
3.
Choose a 8Ω external speaker with 3.5mm mono connector.
Hold
1. key to power on radio, until the LCD displays "RT", the resume work
nish.
All channel and function setting will resume factory default after above operation.
2.

RECEIVER
Sensitivity Less than 1uV for 10dB(S+N)/N
Image Rejection 70dB
Adjacent Channel Rejection 60dB
IF Frequencies 1st 10.695MHz
2nd 455KHz
Automatic Gain Control(AGC) Less than 10dB change in audio
Output for inputs from 10 to 50000uV
Squelch less than 1uV
Audio Output Power 1Watts
Frequency Response 300-3000Hz
TRANSMITTER
Power Output 4 WattsFM/AM
Transmission interference inferior to 4nW(-54dBm)
Frequency Response 300-3000Hz
Modulated signal distortion inferior to 5%
Output Impedance 50 ohms
SPECIFICATION
GENERAL
Modulation Mode AM/FM
Frequency Range 26.565-27.99125MHz
Frequency Tolerance 0.005%
Input Voltage 13.2V
Dimensions(in mm) 104x108x25cm
Weight 416g
Ferquency Control PLL Synthesizer
Operating Temperature
Range -20℃to +50℃
Current Drain
Transmit with push-to-talk /UP/DN and coiled cord
Receive 2A MAX
VOL Max Squelched 0.3A
Weight 0.8A
Antenna Connector UHF,SO-239