APW Wyott BM-80 User manual

PRODUCT: QUANTITY: ITEM #:
Models: BM-80 BM-80D BM-80-UL BM-80D-UL (“D” designates drain)
Designed Smart
Built Solid
APW Wyott Design Features
Options
Insulated Hot Food Wells
Bottom Mount Series
APW Wyott Foodservice Equipment Company · 729 ThirdAve., Dallas, TX 75226
[phone] · [phone] · Fax [phone] · www.apwwyott.com· [email protected] Rev. 5/22/2005
Insulated Bottom Mount Hot Food Well BM-80
• Constructed of deep-drawn 20 ga. type 304 stainless steel.
• Units with drain are provided with stainless steel ½ NPT
drain welded to bottom of pan and provided with
removable screen.
• Entire heat assembly covered with inspection housing
with layer of 1 1/2" thick compressed fiberglass insulation.
Reliability backed by APW Wyott’s Warranty
•AllAPW Wyott food wells are backed by a 1-year parts
and labor warranty, including on-site service calls within
50 miles of authorized service technicians.
• Certified by the following agencies:
• 20 ga. deep-drawn stainless steel well pans.
•Available with or without drain.
• Unit may be used wet or dry (wet use offers best
results).
• Easy access to heating elements.
• Thermostatic control with 36” capillary (effective
length 26”).
• Large indicating pilot light.
• Multiple units can be installed in same table or
counter.
• Multiple wattages and voltage choices
• Thermostat with 72” capillary (effective length 62”)
• Recessed bezel (56360)
• Drain kit (56420)
• Lever operated shut off valve (56360)
• Infinite Controls
• Square corners - BM-80C
See reverse side for product specifications.
Greatest Selection of Hot Food Wells!
• Heavy-duty bottom mount, insulated rectangular drop-in
hot food well is designed for installation in metal
countertop.
• Available with Round Corners or Square Corner (add
a "C" to model number) designs.
• Units available in a UL recognized component
construction with open wires and increase-decrease
plate or complete UL listed construction including
electrical conduit, bezel and control box.
• Available in a variety of wattage power to accommodate
your needs, whether it is for High Performance, Fast
Recovery power or Energy Efficient, Lower wattage
(750 watts) power.
• Available with Welded Drain Design or no drain.
Most Effective Heat System!
• All Bottom Mounted Food Wells are heated by tubular
calrod heat element shaped in serpentine fashion for
even heat distribution to pan base.
• Element is mounted under well and secured by an
aluminized reflector shield for maximum efficiency.
• Thermostatically controlled for fast heat recovery.

Insulated Hot Food Wells
Bottom Mount Series
PRODUCT: QUANTITY: ITEM #:
Models: BM-80 BM-80D BM-80-UL BM-80D-UL (“D” designates drain)
APW Wyott Foodservice Equipment Company · 729 ThirdAve., Dallas, TX 75226
[phone] · [phone] · Fax [phone] · www.apwwyott.com· [email protected] Rev. 5/22/2005
# 1401
*APW Wyott reserves the right to modify specifications or discontinue models without incurring obligation.
PRODUCT SPECIFICATIONS
Construction:
Well is constructed of deep-drawn 20 ga. type
304 stainless steel, with 28 ga., fully insulated
aluminized steel outer housing. Units shipped
with drain are provided with stainless steel 1/2"
NPT drain welded to bottom of pan provided with
removable screen. Unit is heated by a tubular
calrod heat element shaped in serpentine
fashion for even heat distribution to pan base.
Element is mounted under well and secured by
aluminized reflector shield for maximum
efficiency. Top edge of unit has a 13/16" flange.
Recommended flange turndown 3/4". BM-80
Round Corner versions are made with a 1"
radiused. Thermostatic control has 36" capillary
(effective length 26")
Electrical Specifications:
120V, 750W, 6.25 Amps
120V, 1200W, 10 Amps
208V, 1600W, 7.7 Amps
208/240V, 1200/1600W, 5.8/6.7 Amps
208/240/277V, 900/1200/1600W, 4.3/5.0/5.8 Amps
Overall Dimensions:
Outside: 8 5/16”H x 13 13/16”W x 21 3/4”L
(21.1cm x 35.1cm x 55.2cm)
Inside: 6 1/4”H x 12 3/16”W x 20 1/8”L
(15.9cm x 30.9cm x 51.1cm)
Cutout: 11 7/8”W x 19 7/8”L
(30.2cm x 50.5cm)
UL Models: Control size: 5 15/16”W x 6 7/16”H
Control cutout: 5 3/4”W x 6 1/4”H
If UL kit added, 6” clearance
necessary for thermostat box.
Shipping Information:
Weight: 20 lbs. (9.1kg), UL models: 24 lbs. (10.9kg)
Freight Class: 92 1/2
FOB: Dallas, TX 75226