Aqua-Marina BT-88890 User manual

INFLATABLE
FISHING BOATS
User’s Guide
W W W. S I L V E R M A R I N E . C O M
BT-88890
BT-88891
BT-88892
Aqua Marina

8
THANK YOU FOR CHOOSING AQUA MARINA
FISHING SPORT BOATS
“Load your boat with fishes this summer with an AM CLASSIC fishing boat that has a place for
everything!” The AM CLASSIC fishing boat offers great performance, durability and versatility.
Best of all, it’s so easy to set up and transport, simply put it in your car trunk and get some
fishing fun!
This manual has been compiled to help you achieve long term safe use and pleasure from your
Aqua Marina® boats.
GENERAL INFORMATION
SAFETY
In a manual of this type it is impossible to give adequate space to the topic of water safety.
Check in your local area for information and/or training as needed. Inform yourself about local
regulations and dangers related to boating and/or other water activities. It is your responsibility to
be aware of and comply with all relevant safety regulations. For all water recreation or sport you
should have a reasonable swimming ability. Just as swimmers have a cardinal rule about not
swimming alone. It is strongly advised that you should never go boating alone.
PLEASE KEEP THIS MANUAL IN A SECURE PLACE, AND HAND IT OVER TO THE NEW
OWNER WHEN YOU SELL THE CRAFT. RECORD THE "HULL IDENTIFICATION NUMBER"
(HIN) WHICH IS PRINTED ON THE BOAT'S HULL IN THE FOLLOWING BOX:
MANUFACTURER’S CERTIFICATION
This boat comply with ISO 6185 standard established by the International Organization for
Standardization.
MANUFACTURER’S RECOMMENDATION
The total number of persons, motor
power and total weight shall not
exceed the limits labeled (Fig. 1)
on the boat.
Fig.1
2

1. 94/25/EC as amended by Directive 2003/44/EC boat design category
Design Category D “SHELTERED WATERS” Designed for voyages on sheltered coastal
waters, small bays, small lakes, rivers and canals when conditions up to, and including, wind
force 4 and significant wave heights up to, and including, 0,3 m may be experienced, with
occasional waves of 0,5 m maximum height, for example from passing vessels.
2. Country of origin
3. Maximum person’s capacity
4. Manufacturer’s recommended maximum load capacity
5. Manufacturer’s recommended working pressure
6. Hull identification number (HIN)
7. CE mark, manufacturer’s name and address
8. Maximum motor power
SAFETY CHECK LIST & SAFETY WARNING
• Always wear an approved Personal Flotation Device (Life Preserver)
• Be aware of your local boating rules and regulations and abide by them accordingly
• Check inflation levels each time before you go out and inflate your boat for a full 24 hours
before undertaking long trips
• DO NOT allow children to use Aqua Marina unsupervised
• DO NOT consume alcohol while boating or operating a boat while under the influence of
alcohol or drugs
• DO NOT drag your Aqua Marina over rocks or gravel if it can be avoided
• DO NOT exceed the certified maximum capacities of this boat under any circumstance
• DO NOT go boating alone
• DO NOT use compressors, co2 or compressed air for inflation, only use Aqua Marina
recommended pumps
• DO NOT use your Aqua Marina Boat as a personal flotation device as they are designed for
leisure/recreation in mind
• DO NOT sleep inside of your Aqua Marina while on the water
SPECIFICATIONS AND FEATURES
SPECIFICATIONS
STANDARD EQUIPMENT
Items
Models
BT-88890
BT-88891
BT-88892
Items
Models
BT-88890
BT-88891
BT-88892
9.8'x4'4"
(300x134cm)
3+1
4
2+1 0.12 bar hull
400kg(883lbs) 18kg(39.6lbs)
17kg(37.4lbs)
20kg(44lbs)
380kg(838lbs) 410kg(904lbs)
430kg(948lbs) 3KW(4HP)
Size Max
passenger
Air
chambers
Air
pressure
Standard
Max. payload
Max. payload
with optional
plywood deck
Max. motor
power
Net
weight
500W
1 pc 1 pair 1 pc 1 set 1 pc1 pc
With T-18
trolling motor
Gas motor
mount
Trolling motor
mount
Carry
bag
Aluminum
oar
11”
Foot pump
Repair
patch
Pressure
gauge
Wooden
bench seat
Motor
/Motor Mount
3

DESCRIPTION
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
SET UP INSTRUCTION
UNFOLD THE BOAT
Choose a smooth and clean surface to spread the
boat out so that the inflatable chambers can fill easily.
BOSTON SCREW VALVE OPERATION
Follow the instructions below for valve operation and correct inflation and deflation procedures.
1. Double valve cap (valve lets air in, not out). (Fig.1)
2. Quick deflation cap. (Fig.2)
3. Unscrew the double valve cap. (Fig.3)
4. Insert the output end of air pump into the valve and fill. (Fig.4)
5. To deflate, unscrew the quick-deflation cap. (Fig.5) CAUTION: Double valve does not operate
when the cap is off. Do not unscrew this cap while boat is in the water.
1
4
7
10
13
15
Bow carry handle
Inflatable I-beam floor
Aluminum oar
Motor mount(for BT-88890)
Wooden bench seat
* Optional plywood deck
2
5
8
11
14
Grab line
Oar lock
Inflation valve
Boston screw valve
Electric motor mount (for BT-88891and BT-88892)
3
6
9
12
Inflatable cushion seat
Oar holder
Fishing rod holder
Rubbing strake
2
1
3 15 8 10 749
14
11 12135
6
14
4

INFLATION VALVE OPERATION
1. Open external cap and pull firmly to extend out. (Fig.1)
2. Attach suitable adapter nozzle to inflation end of pump. Insert pump and start to pump. (Fig.2)
3. When fully inflated, gently twist adapter sleeve to right while backing pump out of valve.(Fig.3)
4. Fully remove adapter and close external stopper. Valve should appear depressed into
itself. (Fig.4)
INFLATION STEPS
1. Inflate the chambers following the numerical sequence marked on the valves. It is very
important to follow the numerical sequence; failure to do so
will result in an improper inflated boat.
2. Inflate the hull. After inflation, insert the provided pressure
gauge into the air valve to check the air pressure. Ideal
pressure is 1.45psi-0.10bar.
3. Inflate the floor until it is stiff to the touch but NOT hard.
NOTES: Check the pressure every time before usage. Air temperature and weather condition
do affect the internal air pressure of inflatable products. In cold weather the product will lose
some pressure due to the fact that the air will contract. If this occurs, you may want to add a
little air to the product. However, in hot weather, the air will expand. You must let some air out to
prevent the product from failing due to overpressure.
• Only use Aqua Marina® approved inflation pumps
• Never use motor-driven high-pressure air pumps as this may result in over-inflation. Fill with
cold air only
• Under and over-inflation will result in safety hazards
• Always check the inflation pressure before using the boat
• Never stand on or rest objects on the boat during inflation
• Never open the cap of air valve while the boat is in use
• Be sure the valve is tightly closed before using the boat
Double valve capDouble valve cap
Fig.1 Fig.2 Fig.3 Fig.4
Fig.1&2 Fig.3 Fig.4 Fig.5
1
2
Inflate
Deflate
0
1
2
0.1
0
3
4
5
6
7
8
bar
psi
1.45psi-0.1bar
5

Fig.1
Fig.2 Fig.3
HULL ASSEMBLY
1. Wooden bench seat installation
Slide the seat into position by inserting the
flaps on both chamber of the boat into
notches on the Seat Board.
*Optional PLYWOOD DECK INSTALLATION (B0302122)
NOTE: The Plywood deck is an optional accessory for Classic.(Fig.1)
Tip: It's better to inflate the boat about 20% before plywood deck installation.
a. Start by fitting the wooden bow board between the air tubes and bottom. Push it forward as
far as possible until it reaches the top of the bow (Fig. 2) and the air valve of the inflatable floor
fits into the hole of the stern wooden board. Fit the back board to the rear end. (Fig.3)
Fig.4 Fig.5
b. Lift the middle section a bit and create a roof-like structure.(Fig.4)
c. Step on raised part of two connected floor sections and push down the two boards at the joint.
Make sure the deck is flatten by spreading inside the boat (Fig 5).
6

Fig.3.1 Fig.3.2 Fig.3.3
Fig.6 Fig.7
d. Inflate the two side tubes of the boat first by using the foot pump in the package. (Fig.6)
e. Last step is to inflate the floor of the boat with a foot pump to finish. (Fig.7)
2. Motor mount installation (for BT-88890)
• Put straight tubes of the motor mount onto the boat fitting holes. (Fig.3.1)
• Put upper tubes of the motor mount onto the boat fitting holes. (Fig.3.2)
• Adjust to make sure the motor mount fits boat in place and firmly. (Fig.3.3)
3. Electric motor installation
1. Release the small adjustable tension collar from electric motor.
2. Put stainless steel pipe into the upper and the lower buckle of the boat stern.
3. Adjust to make sure the motor fits boat in place and firmly.
4. Fix the tension collar and tighten it.
NOTE:
• The floorboards must be assembled before inflating the boat.
• After the assembly, carefully check the floorboards are secured and tight. If the floorboards
are not tight or smooth, re-do the assembly.
7

Fig.4
Fishing
Rod
Fishing
Rod
Holder
End Cap
Fishing
Rod
Fishing
Rod
Holder
End Cap
4. Fishing rod holder use (Fig.4)
• Slide the end cap over the end of the fishing rod
• Insert the fishing pole into the holder
OUTBOARD MOTOR INSTALLATION
After the boat is fully inflated and well assembled,
attach your outboard motor onto motor mount at the center.
OAR ASSEMBLY
1. Insert “Shaft A” through the oar-lock first.
2. Insert “Shaft A” with the pin end into “Shaft B” with the blade towards outboard (water)
3. Double check and make sure the retainer ring onto the other end of the “Shaft A”, from inside
of the boat.
4. When the oars are not in use secure the oars onto the oar holders located on each side of the
boat.
A
B
Shaft A
Shaft B
Retainerring
NOTE:
• Ensure the motor is always fixed on the motor mount
• Read the instruction of outboard motor for correct installation and operation
• Overpowering a boat can result in serious injury, death or boat damage. Find the maximum
motor power marked on the boat label
8

1
2
3
• Storage is best in a dry room. Ensure protection against rodents and other vermin, as they feed
on the fabric of the canoe
• Store the product and accessories in a dry, temperature controlled, between 32 degrees
Fahrenheit (0 degrees Celsius) and 104 degrees Fahrenheit (40 degrees Celsius) storage
location
PRODUCT CARE AND STORAGE
The boat is made of the highest quality materials and complies with ISO 6185 standards. Altering
the construction of the boat will endanger your own safety, safety of the occupants and void the
limited warranty!
There is very little that you have to do to keep your boat in good condition for many years.
• When landing on the shore, carry the boat. Do not tow it on the sand or ground as damage
may occur
• If you use the tow rings to tow the boat, go slowly to avoid over-towing as damage may occur
• Clean your boat after a trip to prevent damage from sand, salt water or sun exposure. Most dirt
can be removed with a garden hose, a sponge and mild soap. Make sure the boat is
completely dry before storing. Use as few cleaning agents as possible, do not discharge waste
agents into water, and clean your boat preferably on land
• Be sure your product is completely dry before storing
• The products may be stored inflated, but do not place any heavy or sharp objects on it.
Hanging the boat is not recommended
• Open all air valves and deflate boat completely. Remove all the accessories from the boat;
seats and oars
• Fold the bow end twice to the middle of the boat tightly while forcing out any remaining air;
Repeat this procedure for the stern. The boat storage bag is designed to allow you to get your
boat into the bag as easily as possible with minimal folds. Follow the diagram below for the
best folding procedures:
9

LEAK DETECTION AND REPAIR
AIR LEAK DETECTION
If your boat appears a bit soft, it might not be because of a leak. If the boat was inflated late in
the day with 32 °C (90 °F) air, that air might cool down to 25 °C (77 °F) overnight. The cooler air
exerts less pressure on the hull, so it could appear soft the next morning. If there has been no
temperature variation, you need to start looking for a leak:
• Take a good look at your boat from just a few feet away. Flip it over and closely check over the
outside. Any large leaks should be clearly visible
• If you have an idea where your leak is, use a mix of dishwashing liquid and water in a spray
bottle, and spray over the suspicious areas. Any leak will produce bubbles that will pinpoint the
location of the leak
• Check valves for leak, if necessary, spray soapy water around the valve and the valve base
SMALL REPAIRS
Inadvertent punctures can be repaired using included vinyl repair patch. You can purchase
additional PVC or silicon based glue for repairing camping mats, tents or shoes from your local
market to patch your boat. Please refer to the instruction of the glue for patching.
1. Thoroughly clean and dry the damaged area. Completely deflate the product.
2. Cut a portion of the patch to cover the puncture and allow an additional 1/4” on all sides.
Always cut a round patch, never leave square corners.
3. Be sure the repair area is completely dry.
4. Apply generous coat glue to the vinyl repair patch and to the product.
5. Allow the glue to dry for 2 to 3 minutes, or until the glue becomes tacky.
6. Apply the patch to the product, using your thumb or finger; apply even pressure across the
entire surface of the patch. Make sure the edges of the patch are pressed down along the
entire diameter.
7. Allow the product to dry for at least 12 hours before inflating and using.
If there are large tears/cracks, please bring the water craft or any essential equipment part into a
professional repair shop for appropriate repair or replacement.
10