Aqualisa Quartz Electric User manual

QUARTZ™BATH
INSTALLATION
GUIDE

Quartz™ Bath Installation Guide 02
COMPONENTS (HP/COMBI)
Mains fed and separately pumped water systems only

Quartz™ Bath Installation Guide 03
COMPONENTS (GRAVITY PUMPED)
Gravity stored water systems only

Quartz™ Bath Installation Guide 04
IMPORTANT INFORMATION
Safety information
This appliance can be used by children aged
from 3 years and above and persons with
reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be
made by children without supervision.
This product must be installed by a competent
person in accordance with all relevant current
local and national Water Supply Regulations.
ALL PRODUCTS REQUIRING AN ELECTRICAL
CONNECTION MUST BE INSTALLED BY A
QUALIFIED PERSON FOLLOWING THE
LATEST REVISION OF THE ELECTRICAL
WIRING REGULATIONS, BOTH NATIONAL
AND LOCAL AND CERTIFIED TO CURRENT
BUILDING REGULATIONS.
This system should be installed so that other
taps or appliances operated elsewhere within
the premises do not significantly aect the flow.
The Quartz Smart Valve™must not be used with
a hot water supply temperature of over 65ºC.
If the maximum hot water temperature is likely
to rise above 65ºC then a Thermostatic
Blending Valve must be used.
The Quartz Smart Valve™is supplied factory
pre-set at maximum temperature of 45ºC.
The maximum temperature is fully adjustable
to suit site conditions. If adjusted, we
recommend the outlet temperature is set
to a MAXIMUM of 46ºC.
The Quartz Smart Valve™must be installed in an
accessible location for servicing and maintenance.
The Quartz Smart Valve™must not be installed
in situations where either the ambient
temperature is likely to exceed 40ºC or where
freezing may occur.
The bath controller must not be installed in
situations where the ambient temperature is
likely to fall below 5ºC or rise above 40ºC.
We do not recommend the use of a bath
controller in steam therapy facilities.
This appliance must be earthed.
Cables must be protected by a suitably sized
conduit or trunking to avoid risk of damage and
to allow removal for service and maintenance
purposes
Ensure that the conduit is run to avoid the
bath controller fixing holes.
Surface mounted cables must also be protected
by a suitable approved conduit, even in a loft,
where there may be a risk of damage from
vermin.
The power lead must only be replaced by the
manufacturer or his accredited agent.
The bath controller is supplied from a safety
low voltage source.
This product is suitable for domestic use only.
Aqualisa products are supplied complete with
a 1 year guarantee that can be upgraded by
registering the product with Aqualisa.
See www.aqualisa.co.uk/guarantee for details.
Installation of the pumped Quartz Smart
Valve™(for gravity stored systems)
The pumped Quartz Smart Valve™shower
system is designed to operate up to a maximum
static pressure of 100kPa ((1 bar)(10 metres
head)(14.5psi)). Under no circumstances must
the pumped Quartz Smart Valve™be connected
directly to the water main or in line with another
booster pump.
The minimum actual capacity of the cold water
storage cistern should be not less than 225
litres (50 gallons). The capacity of the hot
water cylinder must be capable of meeting
anticipated demand.

Quartz™ Bath Installation Guide 05
Installation of the standard (unpumped)
Quartz Smart Valve™(for balanced
high pressure and unvented systems,
combination boiler systems and
separately pumped gravity systems)
Pressures: The standard (unpumped) Quartz
Smart Valve™is designed to operate up to a
maximum static pressure of 700kPa ((7 bar)
(100psi)). Where pressures are likely to exceed
700kPa ((7 bar)(100psi)), a pressure reducing
valve must be fitted to the incoming mains
supply. A setting of 400kPa ((4 bar)(60psi)) is
recommended. It should be noted that daytime
pressures approaching 600kPa ((6 bar)(80psi))
can rise above the stated maximum overnight.
Special notes for combination
boiler systems
The appliance must have a minimum domestic
hot water rating of 24kW and be of the type
fitted with a fully modulating gas valve.
If in any doubt, please contact the appliance
manufacturer before installation commences.
PLEASE NOTE: DUE TO PERFORMANCE
CHARACTERISTICS OF COMBINATION
BOILERS, SEASONAL INLET TEMPERATURE
CHANGE WILL AFFECT THE QUARTZ SMART
VALVE™OUTLET FLOW RATE RESULTING IN
VARYING SHOWER FLOW RATE AND FLOW
CONTROL RANGE. INLET TEMPERATURE
CHANGE MAY ALSO CAUSE THE
TEMPERATURE DISPLAY TO FLASH; THIS IS
NOT NECESSARILY CHANGING THE OUTLET
TEMPERATURE.
Special notes for separately pumped
gravity systems and universal/negative
head pumps (for divert systems)
We recommend a MINIMUM pump rating of
1.5 bar. For optimum performance a 2.5 bar
pump should be used for all separately
pumped installations.
A twin ended pump is required for use with
single outlet products.
A universal/negative head type twin ended
pump (works on both positive and negative head
conditions) MUST be used with divert products.
The minimum actual capacity of the cold water
storage cistern should be not less than 225
litres (80 gallons). The capacity of the hot water
cylinder must be capable of meeting the
anticipated demand.
THIS PRODUCT IS NOT SUITABLE FOR USE
WITH A SINGLE ENDED PUMP.
Connections
This product incorporates 15mm ‘push-fit’ type
connections. Tube should be cut using a rotary
type cutter and lubricated using a silicone grease,
petroleum jelly, or similar, prior to insertion into
the fitting. 15mm pipework must be used to
connect the product.
If plastic pipe is used, the tube insert must not
increase the tube diameter or extend the cut-
o length by more than 2mm.
THESE FITTINGS ARE NOT SUITABLE FOR
STAINLESS STEEL TUBE. COMPRESSION
FITTINGS MUST NOT BE USED.
Pipe sizing
PLEASE NOTE: Check pipe size requirements for
connections to outlets and accessories. Long pipe
runs, on both inlet and outlet, will reduce the flow
rate at the shower head, 22mm pipe work should
be used on inlets and reduce down to 15mm as
close to the valve as possible to reduce pressure
losses and help maintain flow rate. If using 15mm
pipe, copper pipe is preferred, to optimise
performance minimise the number of elbows used.
If long pipe runs are unavoidable on the outlet, use
copper pipe rather than plastic, particularly if a
diverter is used, and minimise the number of
elbows as the pipe inserts are very restrictive.
Flushing
Some modern fluxes can be very corrosive and,
if left in contact, will attack the working parts of
this unit. All soldering must be completed and the
pipe work thoroughly flushed out in accordance
with current local and national Water Supply
Regulations prior to connection of the product.
Declaration of conformity
Aqualisa Products Limited declares that the
Quartz Smart Valve™and bath controller, in
conjunction with the wired remote, complies with
the essential requirements and other relevant
provisions of the Low Voltage Directive (2014/35/
EU) and the EMC Directive (2014/30/EU).
After installation
Familiarise the end user with the operation of this
product and hand them this guide. Complete and
post the guarantee card or register online at
www.aqualisa.co.uk

Quartz™ Bath Installation Guide 06
QUARTZ™BATH INSTALLATION
This product must be installed by a competent person in accordance with the relevant
Water Supply Regulations.
Prior to installation, ensure all additional guides supplied with this product are read and
understood.
In addition to the guide below, it is essential that the important information (overleaf)
is read and understood and that you have all the necessary components before
commencing installation.
The Quartz™ bath system is supplied with universal fixings intended to secure the
Quartz Smart Valve™ to a suitable surface.
•
!
Although the Quartz Smart Valve™complies with all relevant EMC standards, if incorrectly
sited, it may interfere with digital TV reception. Please follow the recommendations below to
minimise this eect.
If TV interference is an issue a service kit is available (part no: 652102).
See recommended layouts below.
Images of Quartz Smart Valve™for illustration only, refer to instruction 1 for orientation.
Valve colour may vary – the Original Quartz™valve being black, and the Quartz Smart Valve™
being orange.
• Route cables separately, and as far apart from each other as possible.
• Aerial to point away from the Quartz Smart Valve™.
• Ensure the distance between the Quartz Smart Valve™ and the aerial is as large as possible.
DIGITAL TV INTERFERENCE
AERIAL
LARGEST POSSIBLE DISTANCE
DATA
CABLE
POWER
CABLE
CABLE
TO TV
HIGH PROBABILITY
OF INTERFERENCE,
BOTH RADIATED
AND CONDUCTED
POWER
CABLE CABLE
TO TV
DATA
CABLE
AERIAL
SHORT DISTANCE
LAYOUT WHICH COULD CAUSE PROBLEMSLOWEST PROBABILITY OF INTERFERENCE
1
To ensure safe operation and installation of this product, the Quartz Smart Valve™MUST be
installed in one of the orientations shown.
300 mm
210 mm
70 mm
300 mm
210 mm
210 mm
450 mm
450 mm
70 mm

Quartz™ Bath Installation Guide 07
2
Isolation valves are supplied with the Quartz Smart Valve™and
must be fitted on both inlets and the blended water outlet. All
pipe work should be run in 15mm pipe. All pipe work should
be supported. For externally pumped gravity fed installations,
22mm pipe work should be run as close to the Quartz Smart
Valve™as possible before reducing down to 15mm.
To ensure optimum performance use the minimum amount of elbows.
To maximise flow rates we recommend using copper pipe with the minimum amount of elbows.
•
!
The inlet supply centres are 48mm.
Please note arrow on isolation valve to indicate direction of flow.
DO NOT use compression fittings on the inlet and outlet spigots this will aect the
warranty if fitted.
•
!
3
Choose the position for your Quartz Smart Valve™as close to the bath controller as possible.
The Quartz Smart Valve™may be sited in the roof space above the proposed bath site, in the
airing cupboard or behind a screwed bath panel if more convenient. If siting in the roof space,
ensure that freezing cannot occur and that no insulation material is placed under or over the
The Quartz Smart Valve™. Please refer to the system layout diagrams.
The Quartz Smart Valve™MUST be sited in a position that is safely accessible for servicing
and commissioning purposes. When fitted in a loft space, the route to and the area around
the Quartz Smart Valve™must be boarded to ensure a safe working environment.
The optimum position for the Quartz Smart Valve™is in the roof space above the
controller site to take full advantage of the ease and speed of installation.
The distance between the Quartz Smart Valve™and the controller must be within the
range of the 10m data cable supplied.
4
Place the Quartz Smart Valve™on a solid mounting surface, and
place the fixing feet into suitable positions. Mark, then drill and
prepare suitable fixings before securing the Quartz Smart Valve™
to the mounting surface using the screws provided, (if suitable).
5
Flush through both hot and cold supply pipes.
REFER TO SAFETY INFORMATION SECTION
The maximum hot water inlet temperature must be no more than 65˚C.
•
!

Quartz™ Bath Installation Guide 08
6
Attach the supply pipes to the Quartz Smart Valve™, ensuring
that the cold and hot feeds are fitted into the appropriately
marked inlets.
7
Run a pipe from the mixed water outlet of the Quartz Smart Valve™to the proposed siting
for the bath fill outlet.
To ensure optimum performance use the minimum amount of elbows.
To maximise flow rates we recommend using copper pipe with the minimum amount of elbows.
•
!
Suitable non restrictive double check valves (not supplied) MUST be fitted to the blended
outlet pipe in line with the current Water Supply Regulations.
•
!
8
Place the paper template on the wall in the desired location for
the bath controller and mark all fixing points and the data cable
entry point. Remove the template and drill a Ø16mm hole at the
appropriate position for the data cable.
Ensure the data cable is the correct way round as both ends dier in type of connection used.
The data cable should be run in conduit to allow for replacement if required.
Care should be taken to ensure the mounting holes do not pierce the data cable conduit.
•
!
If installing this Quartz™product as a replacement product, it may be necessary to purchase
a concealed retro-fit wall plate to cover the existing hole in the tiling. The cavity in the wall
should be plugged using a suitable material for the wall plate to be
secured to. Contact our Customer Service Department to purchase product code:
QZD.B3.RWP.14 – Quartz Smart Valve™concealed retro-fit wall plate.
9
Drill and prepare the four wall fixings for the bath controller using the fixings provided,
(if suitable).

Quartz™ Bath Installation Guide 09
10
Feed the bath controller connection end of the data cable
through the centre hole in the mounting plate. Run a bead
of silicone sealant in the mastic groove on the back of the
mounting plate and press into position on the finished wall
surface. Ensure the data cable is held securely by the narrow
middle slot of the mounting plate and fix to the wall using the
brass screws provided.
11
Plug the data cable into the rear of the bath controller and push
fully home.
Slide the bath controller onto the mounting plate.
12
Secure the bath controller onto the mounting plate with the
fixing screw located at the base of the bath controller using a
small Pozidriv screwdriver.
•
!
To ensure a watertight seal, we recommend running a thin bead of silicone around the
concealed bath controller once it has been secured to the mounting plate.
13
Connect the outlet pipe to the mixed water outlet on the Quartz Smart Valve™. Using pipe
clips as appropriate, ensure that all pipe work is perpendicular to the Quartz Smart Valve™,
i.e. not putting any strain on the fittings.
To ensure optimum performance use the minimum amount of elbows.
To maximise flow rates we recommend using copper pipe with the minimum amount
of elbows.
Before any electrical adjustment is attempted, the electricity supply must be turned
o at the mains switch.
Electrical installation may only be carried out by a qualified person.
All copper pipe work must be cross-bonded and connected to a reliable earthing point.
•
!

Quartz™ Bath Installation Guide 10
14
Connect the Quartz Smart Valve™power lead to a double pole 3
amp fuse switched spur incorporated in the fixed wiring circuit, in
accordance with current wiring rules (refer to safety information
section). Ensure that this is located in an accessible, dry location
and not in the bathroom.
THIS APPLIANCE MUST BE EARTHED
We recommend protecting surface mounted cables in suitable approved conduit to avoid
the risk of damage from vermin.
The power lead should also be clipped in place with ‘P’ clips or similar to avoid accidents.
•
!
15
Loosen the single fixing screw on the top of the Quartz Smart
Valve™and then carefully tilt the lid up and o the location lugs,
and set the lid aside.
Connect the low voltage, 10m data cable into the socket adjacent
to the temperature adjuster as indicated on the label. Feed the
cable out of the Quartz Smart Valve™ensuring it is correctly
routed within the data cable channel.
A further data cable socket has been provided for use with a wired remote or
diverter. This can be accessed by carefully snapping and removing the entry pillar and
connecting the cable as described above. Please refer to the Wired Remote Installation
Guide or Diverter Installation Guide for the relevant wiring diagrams.
•
!
16
The Quartz Smart Valve™is supplied factory set to either ‘NORMAL HP’ mode or ‘NORMAL
GRAVITY’ mode depending on which product has been ordered.
BALANCED HP SYSTEMS AND SEPARATELY PUMPED GRAVITY SYSTEMS:
The standard QuartzSmart Valve™fits to balanced high pressure
systems or separately pumped gravity systems. It may be set to
‘NORMAL HP’, or for water economy, ‘ECO HP’ mode.
STANDARD COMBINATION BOILER SYSTEMS:
When installed on combi boiler systems, the standard Quartz Smart
Valve™should be set to ‘COMBI’ mode for optimum performance.
GRAVITY PUMPED QUARTZ SMART VALVE™:
The gravity pumped Quartz Smart Valve™installed on gravity systems
ONLY may be set to ‘NORMAL GRAVITY’, or for water economy, ‘ECO GRAVITY’ mode.
In order to fill your bath as quickly and eciently as possible, we recommend the ‘ECO’
settings are not used.
•
!
When making any adjustment to the Quartz Smart Valve™ settings the power MUST
be isolated.
•
!

Quartz™ Bath Installation Guide 11
17
Reinstate the electrical supply to the Quartz Smart Valve™. Press the ‘Start/Stop’
button on the bath controller to turn the bath on.
18
Run the bath at maximum temperature (factory pre set to
45ºC). If required, maximum temperature adjustment can
be made with a flat bladed screwdriver using the ‘MAX TEMP
ADJUSTMENT’ control as indicated. When the temperature
has been set to the desired position, carefully replace the
Quartz Smart Valve™lid and secure the fixing screw, hand
tight only.
Site conditions can aect temperature settings, installer to adjust as required.
•
!

Quartz™ Bath Installation Guide 12
SYSTEM LAYOUT DIAGRAMS
Typical gravity system installation
(compatible with pumped Quartz Smart ValveTM)
Typical combination boiler installation
(compatible with standard QuartzSmart ValveTM)
Typical UHW system installation
(compatible with standard QuartzSmart ValveTM)
Typical thermal storage unit system installation
(compatible with standard QuartzSmart ValveTM)
Typical pumped system installation
(compatible with standard QuartzSmart ValveTM)
Supply
Hot water
cylinder
10m
max
Bath
controller
10m
max
Bath
controller
Central
heating
boiler
Supply
Supply
Pressure
reducing valve
if required
10m
max
Bath
controller
Supply
Hot water cylinder
Connect
‘A’ or ‘B’
Cold feed
to cylinder
B
A
NB: THE BASE OF THE QUARTZ
SMART VALVETM MUST BE SITED
NO HIGHER THAN THE BASE
LEVEL OF THE CISTERN
10m
max
Underside of cistern
Bath
controller
Supply
Underside of cistern
Hot water
cylinder NB: 1.5 bar MINIMUM
universal pump rating
Cold feed
to cylinder
Connect
‘A’ or ‘B’
B
A
10m
max
Bath
controller
Typical gravity system installation
(compatible with pumped Quartz Smart ValveTM)
Typical combination boiler installation
(compatible with standard QuartzSmart ValveTM)
Typical UHW system installation
(compatible with standard QuartzSmart ValveTM)
Typical thermal storage unit system installation
(compatible with standard QuartzSmart ValveTM)
Typical pumped system installation
(compatible with standard QuartzSmart ValveTM)
Supply
Hot water
cylinder
10m
max
Bath
controller
10m
max
Bath
controller
Central
heating
boiler
Supply
Supply
Pressure
reducing valve
if required
10m
max
Bath
controller
Supply
Hot water cylinder
Connect
‘A’ or ‘B’
Cold feed
to cylinder
B
A
NB: THE BASE OF THE QUARTZ
SMART VALVETM MUST BE SITED
NO HIGHER THAN THE BASE
LEVEL OF THE CISTERN
10m
max
Underside of cistern
Bath
controller
Supply
Underside of cistern
Hot water
cylinder NB: 1.5 bar MINIMUM
universal pump rating
Cold feed
to cylinder
Connect
‘A’ or ‘B’
B
A
10m
max
Bath
controller
Typical gravity system installation
(compatible with pumped Quartz Smart ValveTM)
Typical combination boiler installation
(compatible with standard QuartzSmart ValveTM)
Typical UHW system installation
(compatible with standard QuartzSmart ValveTM)
Typical thermal storage unit system installation
(compatible with standard QuartzSmart ValveTM)
Typical pumped system installation
(compatible with standard QuartzSmart ValveTM)
Supply
Hot water
cylinder
10m
max
Bath
controller
10m
max
Bath
controller
Central
heating
boiler
Supply
Supply
Pressure
reducing valve
if required
10m
max
Bath
controller
Supply
Hot water cylinder
Connect
‘A’ or ‘B’
Cold feed
to cylinder
B
A
NB: THE BASE OF THE QUARTZ
SMART VALVETM MUST BE SITED
NO HIGHER THAN THE BASE
LEVEL OF THE CISTERN
10m
max
Underside of cistern
Bath
controller
Supply
Underside of cistern
Hot water
cylinder NB: 1.5 bar MINIMUM
universal pump rating
Cold feed
to cylinder
Connect
‘A’ or ‘B’
B
A
10m
max
Bath
controller

Quartz™ Bath Installation Guide 13
Typical gravity system installation
(compatible with pumped Quartz Smart ValveTM)
Typical combination boiler installation
(compatible with standard QuartzSmart ValveTM)
Typical UHW system installation
(compatible with standard QuartzSmart ValveTM)
Typical thermal storage unit system installation
(compatible with standard QuartzSmart ValveTM)
Typical pumped system installation
(compatible with standard QuartzSmart ValveTM)
Supply
Hot water
cylinder
10m
max
Bath
controller
10m
max
Bath
controller
Central
heating
boiler
Supply
Supply
Pressure
reducing valve
if required
10m
max
Bath
controller
Supply
Hot water cylinder
Connect
‘A’ or ‘B’
Cold feed
to cylinder
B
A
NB: THE BASE OF THE QUARTZ
SMART VALVETM MUST BE SITED
NO HIGHER THAN THE BASE
LEVEL OF THE CISTERN
10m
max
Underside of cistern
Bath
controller
Supply
Underside of cistern
Hot water
cylinder NB: 1.5 bar MINIMUM
universal pump rating
Cold feed
to cylinder
Connect
‘A’ or ‘B’
B
A
10m
max
Bath
controller
Typical gravity system installation
(compatible with pumped Quartz Smart ValveTM)
Typical combination boiler installation
(compatible with standard QuartzSmart ValveTM)
Typical UHW system installation
(compatible with standard QuartzSmart ValveTM)
Typical thermal storage unit system installation
(compatible with standard QuartzSmart ValveTM)
Typical pumped system installation
(compatible with standard QuartzSmart ValveTM)
Supply
Hot water
cylinder
10m
max
Bath
controller
10m
max
Bath
controller
Central
heating
boiler
Supply
Supply
Pressure
reducing valve
if required
10m
max
Bath
controller
Supply
Hot water cylinder
Connect
‘A’ or ‘B’
Cold feed
to cylinder
B
A
NB: THE BASE OF THE QUARTZ
SMART VALVETM MUST BE SITED
NO HIGHER THAN THE BASE
LEVEL OF THE CISTERN
10m
max
Underside of cistern
Bath
controller
Supply
Underside of cistern
Hot water
cylinder NB: 1.5 bar MINIMUM
universal pump rating
Cold feed
to cylinder
Connect
‘A’ or ‘B’
B
A
10m
max
Bath
controller
Typical gravity system installation
(compatible with pumped Quartz Smart ValveTM)
Typical combination boiler installation
(compatible with standard QuartzSmart ValveTM)
Typical UHW system installation
(compatible with standard QuartzSmart ValveTM)
Typical thermal storage unit system installation
(compatible with standard QuartzSmart ValveTM)
Typical pumped system installation
(compatible with standard QuartzSmart ValveTM)
Supply
Hot water
cylinder
10m
max
Bath
controller
10m
max
Bath
controller
Central
heating
boiler
Supply
Supply
Pressure
reducing valve
if required
10m
max
Bath
controller
Supply
Hot water cylinder
Connect
‘A’ or ‘B’
Cold feed
to cylinder
B
A
NB: THE BASE OF THE QUARTZ
SMART VALVETM MUST BE SITED
NO HIGHER THAN THE BASE
LEVEL OF THE CISTERN
10m
max
Underside of cistern
Bath
controller
Supply
Underside of cistern
Hot water
cylinder NB: 1.5 bar MINIMUM
universal pump rating
Cold feed
to cylinder
Connect
‘A’ or ‘B’
B
A
10m
max
Bath
controller

Quartz™ Bath Installation Guide 14
QUARTZ™BATH OVERFLOW FILLER
The bath overflow filler is suitable for baths up to a maximum thickness of 24mm.
•
!
Installation videos are available on our website www.aqualisa.co.uk/installation-videos
or alternatively, scan the QR codes on the reverse of this guide.
Carefully unscrew and remove the overflow filler outlet from the
body assembly and set aside.
1
Carefully unscrew and remove the bath waste clicker assembly
from the waste body and set aside.
2
Oer the bath waste into position ensuring the rubber washer is
correctly aligned between the waste assembly and the bath base.
3
Ensuring the rubber washer is correctly aligned, pass the bath
waste clicker through the bath and secure to the waste body
assembly.
4

Quartz™ Bath Installation Guide 15
Connect the bath waste to a suitable waste pipe.
5
Oer the outlet body assembly into position at the rear of the
bath ensuring the rubber washer is correctly aligned between the
outlet body assembly and bath wall.
6
Ensuring the rubber washer is correctly aligned, pass the overflow
filler outlet through the bath and secure to the body assembly.
7
Remove the relevant inlet blanking plug and attach the flexible
hose to the blended inlet connection.
8
PTFE thread tape MUST be used to guarantee a watertight seal.
•
!
9
Connect the flexible hose to the blended supply pipe ensuring suitable non
restrictive double check valves (not supplied) are fitted in line with current Water
Supply Regulations.

Quartz™ Bath Installation Guide 16
WASTE PIPE EXTENSION KIT
If required for larger baths, a 900mm waste pipe conversion kit is available from
the Aqualisa Customer Service Department. Please contact our Customer Service
Department on 01959 560010.
•
!
Unscrew the clamping nut and remove the waste pipe from the
waste assembly.
1
Remove the clamping nut and sealing washer from the waste pipe and set aside.
2
Carefully cut down the length of the waste pipe, and disconnect
from the outlet assembly, ensuring not to damage the outlet.
3
To reassemble, push the longer waste pipe into position over the outlet, and secure it in
place using a jubilee clip (not supplied).
NOTE: The waste pipe may need to be softened by running it under hot water, to ensure it
slides over the outlet.
4
Please do not leave the bath filler running unattended. Although the overflow will remove
excess water once the bath is overfilled, this may not be sucient to prevent the bath from
overflowing (depending on system conditions).
If you have any queries regarding the installation of this product please contact the
Aqualisa Customer Service Department on 01959 560010.
•
!

Quartz™ Bath Installation Guide 17
USER GUIDE
The Quartz™ bath system has a maximum run time of 12 minutes as a
precaution to prevent overflow.
The bathfill can be stopped at anytime by pressing the ‘Start/Stop’ button.
•
!
Bath overflow filler user guide
1. Push the waste cover to engage the plug fitting.
2. Push the waste cover again to disengage the plug fitting.
Please do not leave the bath filler running unattended. Although the overflow
will remove excess water once the bath is overfilled, this may not be sucient
to prevent the bath from overflowing (depending on system conditions).
If you have any queries regarding the installation of this product please contact
the Aqualisa Customer Service Department on 01959 560010.
•
!
Bath controller user guide
1. Turn the temperature dial to the required setting.
2. Press the ‘Start/Stop’ button on the controller, to
fill the bath.
3. The blue LED display will flash until the selected temperature has
been reached and will then remain constant.
4. The temperature may be adjusted once the bath is filling.
5. Press the ‘Start/Stop’ button on the bath controller to stop the bath filling,
when at the desired depth.

Quartz™ Bath Installation Guide 18
Cleaning and maintenance
Your Quartz™bath system should be cleaned using only a soft cloth and washing up liquid.
The ‘click clack’ waste plug mechanism should be kept clear of debris to ensure the plug
maintains a watertight seal. The plug can be unscrewed and removed to check and clean
the mechanism.
DO NOT USE ABRASIVE CLEANERS
Cleaning and maintenance should not be undertaken by children without supervision by a
person responsible for their safety.
It is imperative that descaling is carried out in accordance with the
manufacturer’s instructions, substances that are not suitable for plastics and
electroplated surfaces must not be used.
•
!

Aqualisa Products Limited
The Flyers Way
Westerham Kent TN16 1DE
Customer Helpline: 01959 560010
Brochure Hotline: [phone]
Website: www.aqualisa.co.uk
Email: [email protected]
Republic of Ireland
Sales enquiries: 01-864-3363
Service enquiries: 01-844-3212
Please note that calls may be recorded for training and
quality purposes.
The company reserves the right to alter, change or modify
the product specifications without prior warning.
™ Trademark of Aqualisa Products Limited.
Scan here for
Quartz™bathfill
installation video
Part No: 703950 Issue 02 Nov 18

Check out our full range of Showers
Electric Showers
Digital Showers
Mixer Showers
Power Showers
Smart Showers
Shower Towers
From Top Shower Brands
Mira Showers
Aqualisa Showers
Triton Showers
Gainsborough Showers
Shower Pumps can upgrade your showering experience even more
Stuart Turner Shower Pumps
Salamander Shower Pumps
Grundfos Shower Pumps