Aqualisa Quartz Electric User manual

Quartz
Digital
Exposed with djust ble height he d
Inst ll tion guide
TM
Qu rtz Digit l exposed with djust ble he d installation instructions Page 1

Qu rtz Digit l exposed with djust ble he d installation instructions Page 2
Qu rtz Digit l exposed
Qu rtz Digit l exposed with
djust ble he d

Qu rtz Digit l exposed with djust ble he d installation instructions Page 3
Components (HP/Combi)
iterature not shown
Components (Gravity pumped)
iterature not shown

Qu rtz Digit l exposed with djust ble he d installation instructions Page 4
Important information
S fety inform tion
This product must be installed by a competent person in accordance with all relevant current Water Supply Regulations.
A SHOWERS REQUIRING AN E ECTRICA CONNECTION MUST BE INSTA ED BY A QUA IFIED PERSON
FO OWING THE ATEST REVISION OF BS 7671 (WIRING REGU ATIONS) AND CERTIFIED TO CURRENT
BUI DING REGU ATIONS.
This product is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning safe use of the product, understanding the hazards involved, by a person responsible for their safety.
Children should be supervised to ensure they do not play with the product.
Cleaning and user maintenance shall not be made by children without supervision.
This system should be installed so that other taps or appliances operated elsewhere within the premises do not
significantly affect the flow.
The shower must not be used with a hot water supply temperature over 65°C.
The processor is supplied factory pre-set at a maximum temperature of 45°C. The maximum temperature is fully
adjustable to suit site conditions. If adjusted, we recommend the outlet temperature is set to a MAXIMUM of
46°C.
The Digital processor must be installed in an accessible location for servicing and maintenance.
The Digital processor must not be installed in situations where either the ambient temperature is likely to exceed
40°C or where freezing may occur.
The control must not be installed in situations where the ambient temperature is likely to fall below 5°C or rise
above 40°C.
We do not recommend the use of Quartz Digital in steam therapy facilities.
This appliance must be earthed.

Qu rtz Digit l exposed with djust ble he d installation instructions Page 5
Cables which are chased into the wall must be protected by a suitably sized conduit or sheathing to allow for
removal in the event of service and maintenance purposes.
Surface mounted cables must also be protected by a suitable approved conduit, even in a loft, where there may
be a risk of damage from vermin.
The power lead must only be replaced by the manufacturer or his accredited agent.
The user control is supplied from a safety low voltage source.
This product is suitable for domestic use only.
Quartz Digital is supplied with a 5 year guarantee.
Inst ll tion of Digit l Gr vity Pumped processor (for gr vity stored
systems)
The Quartz Digital Gravity Pumped shower system is designed to operate up to a maximum static pressure of
100kPa ((1 bar)(10 metres head)(14.5psi)).
Under no circumstances must the pumped processor be connected directly to the water main or in line with
another booster pump.
The minimum actual capacity of the cold water storage cistern should be not less than 225 litres (50 gallons).
The capacity of the hot water cylinder must be capable of meeting anticipated demand.
Inst ll tion of Digit l HP/Combi processor (for b l nced high pressure
nd unvented systems, combin tion boiler systems nd sep r tely
pumped gr vity systems)
Pressures: The Quartz Digital HP/Combi shower system is designed to operate up to a maximum static pressure of
700kPa ((7 bar)(100psi)). Where pressures are likely to exceed 700kPa ((7 bar)(100psi)), a pressure reducing valve
must be fitted to the incoming mains supply. A setting of 400kPa ((4 bar)(60psi)) is recommended. It should be
noted that daytime pressures approaching 600kPa((6 bar)(80psi)) can rise above the stated maximum overnight.
Speci l notes for combin tion boiler systems
The appliance must have a minimum domestic hot water rating of 24kW (80,000BTU) and be of the type fitted
with a fully modulating gas valve.
If in any doubt, please contact the appliance manufacturer before installation commences.
P EASE NOTE: DUE TO PERFORMANCE CHARACTERISTICS OF COMBINATION BOI ERS, SEASONA IN ET
TEMPERATURE CHANGE WI AFFECT THE PROCESSOR OUT ET F OW RATE RESU TING IN VARYING SHOWER
F OW RATE AND F OW CONTRO RANGE. IN ET TEMPERATURE CHANGE MAY A SO CAUSE THE TEMPERATURE
ED’S TO F ASH; THIS IS NOT NECESSARI Y CHANGING THE OUT ET TEMPERATURE.

Qu rtz Digit l exposed with djust ble he d installation instructions Page 6
Speci l notes for sep r tely pumped gr vity systems
We recommend a MINIMUM pump rating of 1.5 bar. For optimum performance a 2.5 bar pump should be used
for all separately pumped installations.
A twin ended pump is required for use with single outlet Digital products.
A universal type twin ended pump (works on both positive and negative head conditions) is required for use with
Digital Divert products.
The minimum actual capacity of the cold water storage cistern should be not less than 225 litres (80 gallons). The
capacity of the hot water cylinder must be capable of meeting the anticipated demand.
THIS PRODUCT IS NOT SUITAB E FOR USE WITH A SING E ENDED PUMP.
Connections
This product incorporates ‘push-fit’ type connections. Tube should be cut using a rotary type cutter and
lubricated using a silicone-based lubricant or petroleum jelly (Vaseline or similar) prior to insertion into the fitting.
If plastic pipe is used, the tube insert must not increase the tube diameter or extend the cut-off length by more
than 2mm.
THESE FITTINGS ARE NOT SUITAB E FOR STAIN ESS STEE TUBE. COMPRESSION FITTINGS MUST NOT BE USED.
Pipe si ing
ong pipe runs, on both inlet and outlet, will reduce the flow rate at the shower head, 22mm pipe work should be
used on inlets and reduce down to 15mm as close to the valve as possible to reduce pressure losses and help
maintain flow rate. If using 15mm pipe, copper pipe is preferred, to optimise performance minimise the number
of elbows used. If long pipe runs are unavoidable on the outlet, use copper pipe rather than plastic, particularly if
a diverter is used, and minimise the number of elbows as the pipe inserts are very restrictive.
Flushing
Some modern fluxes can be very corrosive and, if left in contact, will attack the working parts of this unit. All
soldering must be completed and the pipe work thoroughly flushed out in accordance with current Water Supply
Regulations prior to connection of the product.
After inst ll tion
Familiarise the end user with the Quartz Digital operation and hand them this guide. Complete and post the
guarantee card or register online at www.aqualisa.co.uk

Qu rtz Digit l exposed with djust ble he d installation instructions Page 7
Installation instructions
This product must be installed by a competent person in accordance with the
relevant Water Supply Regulations.
In addition to the guide below, it is essential that the written instructions
overleaf are read and understood and that you have all the necessary
components (shown overleaf) before commencing installation.
The Quartz Digital shower system is supplied with universal fixings intended
to secure it to a suitable wall.
!
!
90mm
445mm
270mm
350mm
265mm
70mm
To ensure safe operation and installation of this product, the processor MUST be
installed in one of the orientations shown.
1
Isolation valves are supplied with the Digital
processor and must be fitted on both inlets and
the blended water outlet. All pipe work should
be run in 15mm pipe. All pipe work should be
supported. For externally pumped gravity fed
installations, 22mm pipe work should be run
as close to the processor as possible before
reducing down to 15mm.
2
The inlet supply centres are 48mm. The inlet supply centres deviate from
EN1111 and EN1287, but are deemed to be a special case. Please note arrow
on isolation valve to indicate direction of flow.
Compression fittings should not be used on the inlet and outlet spigots and
may affect the warranty if fitted.
!
!

Qu rtz Digit l exposed with djust ble he d installation instructions Page 8
Flush out the hot and cold supply pipes.
5
The maximum hot water inlet temperature must be no more than 65°C.
!
Place the Digital processor on a solid mounting
surface, adjusting the fixing feet into suitable
positions. Mark then drill and prepare suitable
fixings before securing the processor to the
mounting surface using the screws provided.
4
Choose the position for your Digital processor
as close to the shower control as possible. The
processor may be sited in the roof space above
the proposed shower site, in the airing cupboard
or behind a screwed bath panel if more
convenient. If siting in the roof space, ensure
that freezing cannot occur and that no insulation
material is placed under or over the processor.
Please refer to the system layout diagrams.
3
!THE PROCESSOR MUST BE SITED IN A POSITION THAT IS SAFE Y
ACCESSIB E FOR SERVICING AND COMMISSIONING PURPOSES. WHEN
FITTED IN THE OFT SPACE, THE ROUTE TO AND THE AREA AROUND THE
PROCESSOR MUST BE BOARDED TO ENSURE A SAFE WORKING
ENVIRONMENT.
The optimum position for the Digital processor is in the roof space above the
shower site to take full advantage of the ease and speed of installation –
please refer to the note above.
The distance between the Digital processor and shower control must be
within range of the 10m data cable supplied.

Qu rtz Digit l exposed with djust ble he d installation instructions Page 9
6Attach the supply pipes to the Digital processor,
ensuring that the cold and hot feeds are fitted
into the appropriately marked inlets.
DO NOT SO DER NEAR TO P ASTIC
COMPONENTS.
!
Drill a hole through the ceiling, a minimum of Ø30mm, maximum Ø40mm.
8
Feed the riser rail assembly containing the
supply pipe and data cable through the hole in
the ceiling, ensuring that the control is at the
desired height, the rail is vertical, and that there
is adequate working clearance above the top of
the rail in the roof space.
9
Temporarily slide the gel hook up the rail ensuring it is positioned higher than
the lower fixing bracket assembly.
10
ocate a suitable entry point into the ceiling for the riser rail, avoiding joists
and services.
7
The centre of the riser rail stands 45mm from the wall. If this is not suitable, the
spacers provided with the fixing brackets will increase the depth to 70mm from
the wall.
!
Place the lower bracket support pillar into
position ensuring the locking lug is correctly
fitted into the location hole.
11

Qu rtz Digit l exposed with djust ble he d installation instructions Page 10
Carefully slide the fixing bracket over the rail
onto the support pillar.
12
Place the upper rail bracket support pillar into
the desired location ensuring that both the
hose restraint and the handset holder are below
the rail wall bracket.
15
Ensuring the rail assembly has been passed through the hole in the ceiling and
is at the desired height, mark the screw holes and remove the fixing bracket.
13
Prepare suitable fixings and slide the fixing bracket back over the rail onto
the support pillar. Secure to the wall using the screws provided.
14
Slide the fixing bracket over the rail onto the
support pillar and repeat the above fixing
procedure.
16

Qu rtz Digit l exposed with djust ble he d installation instructions Page 11
Carefully slide the rail end covers onto the
fixing brackets flush with the finished wall
surface and click the sides firmly into position.
17
Slide the ceiling plate up to the ceiling to cover
the entry hole.
18
The ceiling plate cannot be sited against an
uneven surface. If there is coving or an
alternative obstruction, please ensure the entry
hole is neat and unobtrusive; otherwise the
inner tube could be visible within the showering area.
If the ceiling height is over 2.4m (8ft), a Digital riser rail extension kit will be
required. Contact our Customer Service Department to purchase a riser rail
extension kit (part no: 223217).
!

Qu rtz Digit l exposed with djust ble he d installation instructions Page 12
Connect the outlet pipe to the mixed water outlet on the Digital processor,
using the push-fit elbow provided. Using pipe clips as appropriate, ensure that
all pipe work is perpendicular to the processor, i.e. not putting any strain on
the fittings.
19
Do not solder any additional pipe work to the 15mm copper pipe from the
Digital shower system as the low voltage data cable could be damaged.
Instead, use push-fit fittings where necessary, to connect additional
copper piping.
TO ENSURE OPTIMUM PERFORMANCE USE THE MINIMUM AMOUNT
OF E BOWS.
TO MAXIMISE F OW RATES WE RECOMMEND USING COPPER PIPE WITH
THE MINIMUM AMOUNT OF E BOWS.
BEFORE ANY E ECTRICA ADJUSTMENT IS ATTEMPTED, THE E ECTRICITY
SUPP Y MUST BE TURNED OFF AT THE MAINS SWITCH.
E ECTRICA INSTA ATION MAY ON Y BE CARRIED OUT BY A QUA IFIED
PERSON.
!
Connect the processor power lead to a double
pole 3amp switched fused spur, incorporated in
the wiring circuit, in accordance with current
wiring rules. Ensure that this is located in an
accessible, dry location and not in the
bathroom.
20
THIS APP IANCE MUST BE EARTHED.
We recommend protecting surface mounted cables in suitable, approved
conduit to avoid the risk of damage from vermin.
The data cable and power lead should also be clipped in place with ‘P’ clips or
similar, to avoid accidents.
!

Qu rtz Digit l exposed with djust ble he d installation instructions Page 13
Connect the low voltage data cable into the
socket adjacent to the temperature adjuster
as indicated on the label. Feed the cable out of
the processor box ensuring it is correctly
routed within the data cable channel.
22
A further data cable socket has been provided
for use with the secondary Digital remote
control or Digital diverter. This can be accessed by carefully snapping and
removing the entry pillar and connecting the cable as described above.
!
Unscrew the single fixing on top of the
processor box and then carefully tilt the lid up
and off the location lugs and pull the lid clear.
21
Connect the power to the processor and press
the ‘Start/stop’ button on the controller to turn
the shower on. Ensuring the hose washers are
fitted at either end of the shower hose, attach
the hose and flush the system through for 15
seconds to clear any debris. Turn the shower off
and isolate from the electricity supply.
23

Qu rtz Digit l exposed with djust ble he d installation instructions Page 14
Thread the shower hose through the hose
restraint.
24
Ensuring the hose washer is in the correct
position, depress the anti-swivel locking button
on the handset and secure the handset to the
hose, then place the handset into the handset
holder.
25
The Digital processors are supplied factory set
with the flow rate at either ‘NORMA HP’ or
‘NORMA GRAVITY’ mode depending on which
shower system has been ordered.
HP/COMBI PROCESSORS ON BA ANCED HP
SYSTEMS:
HP/Combi Digital processors fitted to balanced
high pressure systems may be set to ‘NORMA HP’, or for water economy,
‘ECO’ modes.
HP/COMBI PROCESSORS ON COMBINATION BOI ER SYSTEMS:
For HP/Combi Digital processors installed on combi boiler systems, for optimum
performance we recommend setting the flow rate to the ‘COMBI’ mode.
26
N.B. The ‘ECO’ flow rate mode should not be selected for shower systems fitted
to combination boilers.
GRAVITY PUMPED PROCESSORS:
Gravity Pumped Digital processors fitted to gravity systems may be set to
‘NORMA GRAVITY’, or for water economy, ‘ECO’ flow rate modes.
WHEN MAKING ANY ADJUSTMENT TO THE PROCESSOR SETTINGS THE
POWER MUST BE ISO ATED.
!

Qu rtz Digit l exposed with djust ble he d installation instructions Page 15
Run the shower at maximum temperature
(factory pre set to 45°C). If required, maximum
temperature adjustment can be made with
a flat bladed screwdriver using the ‘MAX TEMP
ADJUSTMENT’ control as indicated. When the
temperature has been set to the desired
position, carefully replace the Digital processor
lid and secure the fixing hand tight only.
28
Site conditions can affect temperature settings, installer to adjust as required.
A COPPER PIPE WORK MUST BE CROSS-BONDED AND CONNECTED TO
A RE IAB E EARTHING POINT.
!
Re-instate the electricity supply to the Digital processor. Press the ‘Start/stop’
button on the controller to turn the shower on.
27

Aqualisa Products imited
The Flyer’s Way
Westerham Kent TN16 1DE
Customer helpline: 01959 560010
Brochure Hotline: [phone]
Website: www.aqualisa.co.uk
Email: [email protected]
Republic of Ireland
Sales enquiries: 01-864-3363
Service enquiries: 01-844-3212
Part No:700994 Issue 01 Jan 14
Please note that calls may be recorded for training and quality purposes
The company reserves the right to alter, change or modify the product specifications without prior warning
® Registered Trademark Aqualisa Products imited

Check out our full range of Showers
Electric Showers
Digital Showers
Mixer Showers
Power Showers
Smart Showers
Shower Towers
From Top Shower Brands
Mira Showers
Aqualisa Showers
Triton Showers
Gainsborough Showers
Shower Pumps can upgrade your showering experience even more
Stuart Turner Shower Pumps
Salamander Shower Pumps
Grundfos Shower Pumps