Aqualisa DCV ACY1015 User manual

DCV ACCESSORIES
INSTALLATION
GUIDE

2
CONTENTS
Parts Supplied 3
Warranty 5
Before You Start 5
Fixed Heads Installation 5
Fixed Arms Installation 6
Wall Outlet Installation 8
Shower Kit Installation 9
Brass Wall Mount Installation 11
TOOLS REQUIRED (Tools not supplied)
PTFE
We have taken great care to ensure that this product reaches you in
perfect condition. However should any parts be damaged or missing
please contact your point of purchase. This does not aect your statutory
rights. In addition if you require replacement parts please contact the
Aqualisa customer helpline on 01959 560010 for assistance.
GENERAL CLEANING
Whilst modern plating techniques are used in the manufacture of these
fittings, the plating will wear if not cleaned properly. The safest way
to clean your product is to wipe with a soft damp cloth. Stains can be
removed using washing up liquid.
DO NOT USE ABRASIVE CLEANERS.

3
PARTS SUPPLIED
ADJUSTABLE SHOWER KIT NO. DESCRIPTION QTY
1 Wall Plugs 2
2 Upper Rail Bracket 1
3 Short Wall Screw 1
4 End Caps 2
5 Handset Holder 1
6 Handset 1
7 Riser Rail 1
8Shower Hose - 1.5m 1
9 Hose Restraint 1
10 Lower Rail Bracket 1
11 Long Wall Screw 1
3
11
6
5
7
8
91
4
4
2
10
1
ACY1010 includes 1.5m metal hose - Chrome
ACY1011 includes 1.5m smooth hose - Satin
(Metal hose shown for illustrative purposes)
BRASS WALL MOUNT HOLDER NO. DESCRIPTION QTY
1 Cover Plate 1
2 Wall Plugs 2
3 Backplate 1
4 Allen Key 1
5 Wall Screws 2
6 Handset Holder 1
7 Grub Screws 2
1
3
6
2
5
47
ACY1015

4
FIXED HEADS NO. DESCRIPTION QTY
1 Shower Head 1
2Ball Joint 1
3 Filter Washer 1
1
2
3
12
3
1
2
3
12
3
ACY1005 200mm square
ACY1006 300mm square
ACY1004 200mm round
ACY1007 300mm round
FIXED ARMS - WALL AND CEILING NO. DESCRIPTION QTY
1 Backnut 1
2 Backnut Washer 1
3 Fixing Nut 1
4 Cover Plate 1
5 Shower Arm 1
2
1
4
5
2
1
4
3
5
1
2
3
4
5
2
1
4
5
2
1
4
3
5
1
2
3
4
5
2
1
4
5
2
1
4
3
5
1
2
3
4
5
ACY1003
ACY1002
ACY1001
BRASS WALL OUTLETS NO. DESCRIPTION QTY
1 Backnut 1
2 Backnut Washer 1
3 Wall Cover Plate 1
4 Wall Outlet 1
1
2
3
4
ACY1013 Wall outlet
ACY1014 Wall outlet incl. handset holder

5
BEFORE YOU START
This shower should be installed by a competent person in compliance with
current Water Supply Regulations. For further details contact your Local
Water Authority.
a. Identify all components and check pack contents.
b. Turn o water mains supply.
Before making any pipe connections all supplies MUST be
thoroughly flushed to remove any debris.
WARRANTY
Aqualisa products are supplied complete with a 1 year guarantee that can
be upgraded by registering this product with Aqualisa.
See www.aqualisa.co.uk/warranty for details.
FIXED HEADS INSTALLATION
Ensuring the filter washer is in the correct position, attach the fixed
head to the fixed arm by screwing the ball joint into place.
1
Shower head Ball joint
Filter washer
Shower head Ball joint
Filter washer
Shower head Ball joint
Filter washer
Shower head Ball joint
Filter washer
Open the shower valve and check for leaks.
2

6
FIXED ARMS INSTALLATION
Backnut washer
Backnut
Cover plate
Shower arm
Backnut washer
Backnut
Cover plate
Fixing nut
Shower arm
Backnut
Backnut washer
Fixing nut
Cover plate
Shower arm
Backnut washer
Backnut
Cover plate
Shower arm
Backnut washer
Backnut
Cover plate
Fixing nut
Shower arm
Backnut
Backnut washer
Fixing nut
Cover plate
Shower arm
Backnut washer
Backnut
Cover plate
Shower arm
Backnut washer
Backnut
Cover plate
Fixing nut
Shower arm
Backnut
Backnut washer
Fixing nut
Cover plate
Shower arm
Backnut washer
Backnut
Wall
Female fitting
(not supplied)
Wall
Backnut washer
Backnut
Cover plate
Shower arm
Backnut washer
Backnut
Cover plate
Fixing nut
Shower arm
Backnut
Backnut washer
Fixing nut
Cover plate
Shower arm
Backnut washer
Backnut
Wall
Female fitting
(not supplied)
Wall
With rear access:
Without rear access:
These instructions apply to:
ACY1001 Ceiling arm
ACY1002 Rounded wall arm
ACY1003 Squared wall arm
(ACY1003 shown for with/without
illustrative purposes)
Note: For round fixed wall and ceiling
arms only, fit the cover plate and fixing
nut (flat side of fixing nut facing the
wall) to the shower arm.

7
Connect the fixed arm to a suitable ½” female connector using
PTFE tape or similar, to achieve a watertight seal.
3
Temporarily cap o the fixed arm, open the shower valve and check for leaks.
4
Feed the fixed arm thread through a 22-28mm hole in the wall
and secure with the backnut ensuring the backnut washer is fitted
between the backnut and the wall, if accessible.
2
Run pipework from the shower valve to the desired location for the
fixed arm ensuring it terminates in a suitable ½” female connector (not
supplied). All pipework and connectors must be secured using suitable
fixings. Note: For round fixed wall and ceiling arms only, fit the cover plate
and fixing nut (flat side of fixing nut facing the wall) to the shower arm.
1
With rear access:
Run pipework from the shower valve to the desired location for the
fixed arm ensuring it terminates in a suitable ½” female connector (not
supplied). All pipework and connectors must be secured using suitable
fixings. Note: For round fixed wall and ceiling arms only, fit the cover plate
and fixing nut (flat side of fixing nut facing the wall) to the shower arm.
1
The backnut and backnut washer are not required. Wind the fixed arm
thread directly into the ½” female connector (not supplied) using PTFE
tape or similar, to achieve a watertight seal.
Temporarily cap o the fixed arm, open the shower valve and check for leaks.
2
3
Without rear access:

8
Run pipework from the shower valve to the desired location for the
wall outlet ensuring it terminates in a suitable ½” female connector
(not supplied). All pipework and connectors must be secured using
suitable fixings.
1
With rear access:
Connect the wall outlet to a suitable ½” female connector using
PTFE tape or similar, to achieve a watertight seal.
3
Temporarily cap o the wall outlet, open the shower valve and check
for leaks.
4
Feed the wall outlet thread through a 22-28mm hole in the wall
and secure with the backnut ensuring the backnut washer is fitted
between the backnut and the wall, if accessible.
2
Wall outlet incl.
handset holder
Backnut washer
Backnut
Wall
Cover plate
Wall outlet incl.
handset holder
Cover plate
Female fitting
(not supplied)
Wall
WALL OUTLET INSTALLATION
With rear access: Without rear access:
Wall outlet incl.
handset holder
Backnut washer
Backnut
Wall
Cover plate
Wall outlet incl.
handset holder
Cover plate
Female fitting
(not supplied)
Wall
These instructions apply to both:
ACY1013 Wall outlet
ACY1014 Wall outlet incl. handset holder
(ACY1014 shown for illustrative purposes)

9
Attach the lower rail bracket onto the bottom of the rail.
4
Run pipework from the shower valve to the desired location for the
wall outlet ensuring it terminates in a suitable ½” female connector
(not supplied). All pipework and connectors must be secured using
suitable fixings.
1
The backnut and backnut washer are not required. Wind the wall outlet
thread directly into the ½” female connector (not supplied) using PTFE
tape or similar, to achieve a watertight seal.
Temporarily cap o the wall outlet, open the shower valve and check
for leaks.
2
3
Without rear access:
SHOWER KIT INSTALLATION
Prepare two fixing points, using the fixings provided.
Note: The maximum distance between fixing points is 620mm
1
Fit the hose restraint to the rail followed by the handset holder. The
handset holder button must be depressed whilst fitting. The button
must be to the left of the rail, and the holder to the right.
2
Secure the upper rail bracket into position on the finished wall
surface using the short wall screw.
3

10
Place the end caps into the upper and lower rail brackets and push
firmly into position.
7
Ensuring the hose washer is in the correct position; attach the
non-conical end of the hose to the wall outlet. Run the shower for a
few seconds to clear any debris that may be present.
Pass the conical end of the shower hose through the hose restraint.
Ensuring the hose washer is in the correct position; attach the
conical end of the hose to the shower head, then place the hose in
the handset holder.
Run the shower and check for leaks.
8
9
10
11
Slide the rail assembly up through the upper rail bracket.
5
Align the small hole in the rail with the
lower rail bracket. Secure the lower
rail bracket to the wall, using the long
wall screw.
6

11
BRASS WALL MOUNT HOLDER INSTALLATION
Cover plate
Handset holder
Wall screws
Backplate
Wall plugs
Grub screws
Allen key
Push the cover plate to the wall.
5
Using the backplate as a template, mark and prepare two holes in
the desired location using the fixings provided.
1
Secure the backplate into position using the wall screws.
2
Loosen the grub screws located within the handset holder using the
allen key provided. Oer up the handset holder to the backplate
ensuring the handset holder sits flush to the finished wall surface.
3
Tighten the grub screws using the allen key provided.
4

Aqualisa Products Limited
The Flyers Way
Westerham Kent TN16 1DE
Customer Helpline: 01959 560010 | Brochure Hotline: [phone]
Website: www.aqualisa.co.uk | Email: [email protected]
Warranty: www.aqualisa.co.uk/warranty
Republic of Ireland
Sales enquiries: 01-864-3363
Service enquiries: 01-844-3212
Drawing No: 8136 Issue 01 Apr 19
Please note that calls may be recorded for
training and quality purposes.
The company reserves the right to alter, change
or modify the product specifications without
prior warning.
™ Trademark of Aqualisa Products Limited.