ARGON18 E-118 NEXT User manual

E-118 NEXT 216A: ASSEMBLY GUIDE
Revision 6.0 - 05-03-2017

Assembly overview.......................................2-4
1. Frame inspection ........................................5
2. Fork installation........................................6-7
3. Handlebar installation ................................8-12
4. Handlebar assembly ................................ 13-14
5. Cable housing installation........................... 15-16
6. Electronic drive-train specication................... 17-20
7. Front brake installation.............................. 21-23
8. Rear brake installation .............................. 24-25
9. Armrest assembly .......................................26
10. Seatpost installation ...................................27
11. Saddle adjustment................................. 28-29
12. Derailleur hanger adjustment ..........................30
13. Parts’ SKUs and Descriptions ....................... 31-34
E-118 NEXT 216A: Table of contents
For the warranty to be valid, the bicycle must
be fully assembled by an authorized Argon
18 dealer. High end components, particularly
carbon parts, need extra care when assembled.
Those components must be installed using a
calibrated torque wrench to make sure every
bolt is at the right torque setting to prevent
damage.

2. Fork installation1. Frame inspection
5. Cable housing installation
IMPORTANT NOTICE: It is easier to install the
cables and cable housings before the bearings.
6. Electronic drive-train
specication
3. Handlebar installation
4. Handlebar assembly
2
E-118 NEXT 216A: Assembly overview

9. Armrest assembly
12. Derailleur hanger adjustment10. Seatpost installation 11. Saddle adjustment
3
E-118 NEXT 216A: Assembly overview
8. Rear brake installation7. Front brake installation

13. Parts listing
4
E-118 NEXT 216A: Assembly overview

Parts installed on the frame Description Screw Torque Detail
type Nm
1 Front derailleur hanger Screw (2) 3mm 4Nm Loctite
2 Rear derailleur hanger Screw (2) 3mm 4Nm Loctite
3 Bottle cage Screw (4) 4mm 3Nm Grease
4 Bottom bracket cover Screw (2) 5mm 2Nm Grease
When assembling a new frame, be sure to check if the following parts are assembled correctly.
5
E-118 NEXT 216A: 1. Frame inspection

2.1 Install bearings 27 MR136 (1 ¼’’)
and 26 MR122 (1 1/8’’) inside the
frame after greasing the surfaces.
2.2 Install the fork by placing the lower
part rst, and then balancing the upper
part in its nal position.
6
E-118 NEXT 216A: 2. Fork installation
27
26
GREASE
GREASE

2.3 Slightly unscrew the steering
column set screw (4c) located on the
fork.
2.4 Screw in the compression column
(4b) (specic to the size of your frame)
inside the head tube. The threads
must be lightly greased until the
compression column can be inserted
smoothly and tightly.
2.5 Screw in the safety screw (4c) at
6Nm.
7
E-118 NEXT 216A: 2. Fork installation
4b
4c
GREASE
GREASE
6Nm

3.1 Choose the desired position of
the handlebar: high (+ 2.5cm) or low
(- 2.5cm).
3.2 Apply grease on the 4 screws (6)
(M6x22mm) and tighten them at 6Nm
in an alternate way.
8
E-118 NEXT 216A: 3. Handlebar installation
6
GREASE
6Nm

3.3 Install vertical spacers (17) and two
sleeve nuts (15).
See next page for stack conguration
options.
9
E-118 NEXT 216A: 3. Handlebar installation (continued)
15
17
GREASE 5Nm
5Nm
5Nm 5Nm
CARBON FIBER
ASSEMBLY
COMPOSITE