Argos PRO FITNESS XT2000 Owner's manual

These instructions contain important information which will help you get best from your
equipment and ensure safe and correct assembly, use and maintenance.
If you need help or have damaged or missing parts, call the Customer Helpline:0345 600 1714
or visit www.argos-support.co.uk
Assembly & User Instructions- Please Keep for future reference
Important – Please read these instructions fully before assembly or use
XT2000 Cross Trainer
869/3653

Contents
Safety Information
2-3
Components - Parts
4
Components – Fixings
5
Assembly Instructions
6-13
Workout Area
14
Exercise Information
15-27
. Before Starting
15
. Muscle Chart
16
. Warning up and Cooling Down
17-18
. Console operation
19-27
Care and Maintenance
28
Exploded Parts Diagram
29
Parts List
30-31
1

、
This exercise equipment is built for optimum safety. However, certain precautions apply whenever you
operate a piece of exercise equipment. Be sure to read the entire manual before you assemble, operate or use
this equipment.
Assembly
• The product must be installed on a stable and
level surface. To protect the floor or carpet from
damage, place a mat under the cross trainer.
• Assemble the item as close to its final position
(in the same room) as possible.
• Make sure you have enough space to layout the
parts before starting.
• Keep children and animals away from the work
area, small parts could pose a choking hazard if
swallowed.
• Dispose of all packaging carefully and responsibly.
• Check you have all the components and tools
listed in the parts list, bearing in mind that, for ease
of assembly, some components are pre-assembled.
• The assembly of this equipment is best carried
out by 2 people.
Use
• It is the responsibility of the owner to ensure that all
users of this product are properly informed as to how
to use this product safely.
• This product is intended for domestic use only.
Do not use in any commercial, rental, or institutional
setting.
•Use the equipment only for intended use, as
described in this manual. Do not use attachments not
recommended by the manufacturer.
• Keep this equipment indoors, away from moisture
and dust. Do not put the equipment in a garage,
outbuilding, covered patio, or near water.
• Your product is intended for use in clean dry
conditions. You should avoid storage in excessively
cold or damp places as this may lead to corrosion
and other related problems that are outside our
control.
• Keep unsupervised children away from the
equipment.
• Disabled persons should not use the equipment
without a qualified person or doctor in attendance.
• Always wear appropriate workout clothing when
exercising. Do not wear loose or baggy clothing, as
it may get caught in the equipment. Wear trainers
to protect your feet while exercising.
•Do not place any sharp objects around the
equipment.
• Keep hands away from all moving parts.
• If any of the adjustment devices are left projecting,
they could interfere with the user’s movement.
• Before using the equipment to exercise, always
perform stretching exercises to properly warm up.
• Only one person at a time should use the equipment.
• If the user experiences dizziness, nausea, chest
pain, or other abnormal symptoms stop the workout
and seek immediate medical attention.
• Injuries to health may result from incorrect or
excessive training.
• This product is suitable for a maximum user weight
of: 120kg.
Important – Please read fully before assembly or use
Safety Information
2

• This product conforms to: BS EN ISO 20957-1 and -
9 Class (H) - Home Use - Class (C).
• This stationary training equipment is not suitable for
high accuracy purposes
• The cross trainer is not equipped with a free wheel
and therefore the moving parts cannot be stopped
immediately.
• To mount and dismount the equipment safely, hold
the handlebar and step on/down the footplatform
when it is in the lowest position.
• When choosing a location for the equipment make
sure that the location and position permit access to a
plug.
• Keep the power cord away from any heated
surface
• Do not operate the equipment if the power cord or
plug is damaged,or if the equipment is not working
properly.
• Always examine your examine bike before use to
ensure all parts are in working order.
• Never insert any object or baby parts into any
opening.
3
Warning: Before beginning any exercise program, consult your Doctor. This is especially important
for persons over the age of 35 or persons with pre-existing health problems. You MUST read all instructions
before using any fitness equipment. Argos and its associates assumes no responsibility for personal injury
or property damage sustained by or through the use of this product. Over exercising may result in serious
injury or death. If you feel faint stop exercising immediately. Warning! Heart rate monitoring systems may be
inaccurate. For the most accurate heart rate measure, please hold both hand pulse sensors continuously
during any programme.
Safety Information
Important – Please read fully before assembly or use

Note: Some of the smaller components may be pre-fitted to larger components. Please check carefully
before contacting Argos regarding any missing components.
Components - Parts
If you have damaged or missing parts, please call the
Customer Helpline: 0345 600 1714
http://www.argos-support.co.uk
.
4
Please check you have all parts listed below
11.Front Post
2.Left Footplate Bar
3.Right Footplate Bar
8.Handles(L&R)
4.Front Stabilizer
5.Rear Stabilizer
10.Fixed Handle
24/25. Handrail Bottom
Cover X 2
26/27.L&R Foot
Bar Cover
32/33.L&R Footplate
35/36. Handrail
Front/Rear
Cover X 2
37. Front Post
Ring X 1
43.Bottle Holder
48.M8 T-Shaped
Knob
Cover X 2
60.Console
90/91.L&R Front Cover
92.Power Adaptor
1.Main Frame
94/95. L/R Front Post
Cover x 2

Note: The quantities below are the correct amount to complete the assembly. In some cases more
hardware may be supplied than are required. Some of the fixings are pre-fitted to the larger components.
Please check carefully before contacting Argos regarding any missing fixings.
Components – Fixings
Please check you have all the fixings listed below
81
82
83
70
59
M10x69 Allen Bolt x 2
87
80
79
75
74
73
71
69
85
M8x87 Allen Bolt x 2
M8×42mm Hex Bolt x 4
Ø9×Ø22×R19mm Arc Washer x 6
Ø10mm Washer x 4
M10×20mm Allen Bolt x 4
Ø8mm Washer x 10
M10 Nut x 2
M8×15mm Allen Bolt x 12
ST4.2×15mm Philips Screw x 3
M8 Nut x 6
Ø8mm Spring Washer x 12
Plastic Ring x 2
Ø10mm Spring Washer x 4
Multi Wrench
6# Allen Key
5# Allen Key
86
ST4.2×15mm Philips Screw x 10
88
ST4.8×15mm Philips Screw x 2
5

Total mass of the product is 43 kg. Total size of the equipment is (width) 67.5 cm × (depth) 122.5 cm ×
(height) 160.5 cm.
1Main Frame
2Left Footplate Bar
3Right Footplate Bar
4Front Stabilizer
5Rear Stabilizer
8Handle (L&R)
10 Fixed Handle
11 Front Post
12 Left Action Arm
13 Right Action Arm
21 Transport Wheel (L&R)
22 Level Foot
24 Left Handle Bottom Cover
25 Right Handle Bottom Cover
26 Left Footplate Bar Cover
27 Right Footplate Bar Cover
32 Left Pedal
33 Right Pedal
34 Handrail Axle Sleeve
35 Handrail Front Cover
36 Handrail Rear Cover
37 Front Post Ring
43 Water Bottle Bracket
48 T-shaped Knob
59 Plastic Ring
60 Console
90 Left Front Post Cover
91 Right Front Post Cover
92 Power Charge
94 Left Front Post Cover
95 Right Front Post Cover
Assembly Instructions
6

Assembly Instructions
a. Attach the Front Stabilizer (4) to the Main Frame (1) using 2 x M10x20mm Allen Bolts (80), 2 x 10mm
Washers (74) and 2x10mm Spring Washers (71).
b. Attach the Rear Stabilizer (5) to the Main Frame (1) using 2 x M10x20mm Allen Bolts (80), 2 x 10mm
Washers (74) and 2x10mm Spring Washers (71).
Note: The round gear on the Leveling Feet (22) can be rotated to ensure the cross trainer sit flat on the
ground as shown in the diagram. Turn it anti clockwise to increase height and turn it clockwise to
decrease height.
Step 1
7

Assembly Instructions
Step 2
a. Attach the Left Footplate (32) to the Left Footplate Bar (2) using 3 x M8×15mm Allen Bolts (79), 3 x
Ø8mm Spring Washers (73) and 3 x Ø8mm Washers (75).
b. Attach the Right Footplate (33) to the Right Footplate Bar (3) using 3 x M8×15mm Allen Bolts(79), 3 x
Ø8mm Spring Washers (73) and 3 x Ø8mm Washers (75).
c. Fix the Left & Right Footplate Bar (2, 3) to the Crank Connector (6) using 2 x Ø10×69mm Allen Bolts
(81) and 2 x M10 Nuts (69).
8

Assembly Instructions
a. Connect the Wire (C) to the wire (C1).
b. Fix the Front Post (11) to the Main Frame (1) using 6 x M8×15mm Allen Bolts (79), 6 x Ø8mm Spring
Washers (73), 2 x Ø9xØ22×R30mm Arc Washers (85) and 4 x Ø8mm Washers (75).
Step 3
9

Assembly Instructions
a. Fix the Left Footplate Bar (2) to the Left Action Arm (12) using 1 x Ø11.5×67mm Allen Bolt (82) and 1 x
M8 Aircraft Nut (70).
b. Fix the Right Footplate Bar (3) to the Right Action Arm (13) using 1 x Ø11.5×67mm Allen Bolt (82) and
1 x M8 Aircraft Nut (70).
10
Step 4

Step 5
a. Attach the Handle (10) to the bracket on the Front Post (11), and secure with M8 Lock knob (48).
Note: To adjust the position of the handle, turn the M8 lock knob (48) anti clockwise to loose the
handle (10) as shown in the diagram, and adjust the handle (10) to your required position, then
secure the M8 lock knob (48).
b. Pass the two signal cables (B) on the Fixed Handle (10) into the holes on both sides of the Front
Post (11) and out of the top hole on the Front Post (11).
c. Connect the signal cables A1 and B1 on the Console (60) with the signal cables A and B from the
Front Post (11), respectively.
d. Attach the Console (60) to the Front Post (11) using 4 x M5x8MM Dome Head Philips Bolt (84).
a) Note: Part (84) is pre-assembled.
e. Slide the Left Handle Cover (90) from Right Handle Cover (91) to the left and right ends of the
Handle (10) respectively,and put two Joint Rings (59) on the left and right side of the Handle (10)
respectively, and then push them together from both sides.
f. Lock the Left & Right Handle Cover (90, 91).to Front Post (11) using 4 x ST4.2x15mm Philips Screw
(86).
Assembly Instructions
11

Assembly Instructions
a. Insert the Left Handle (8L) to the Left Action Arm (12); insert the Right Handle (8R) into the Right
Action Arm (13).
b. Fix the Left Handle (8L) to the Left Action Arm (12) using 2 x M8×42mm Hex Bolt (83), 2 x
Ø9×Ø22×R19mm Arc Washers (85) and 2 x M8 Nuts (70).
c. Fix the Right Handle (8R) to the Right Action Arm (13) using 2 x M8×42mm Hex Bolt (83), 2 x
Ø9×Ø22×R19mm Arc Washers (85) and 2 x M8 Nuts (70).
d. Put the Front Post Ring (37) on the Front Post (11). Attach the Front Post Cover (94 & 95) to the
Main Frame (1) and the Front Post Ring (37) with 3 x ST4.2 x 15mm Phillips Screws (87).
Step 6
12

Assembly Instructions
Step 7
a. Fix the Handle Front Cover (35) and Handle Rear Cover (36) to the Left Action Arm (12) and Right
Action Arm (13) respectively using 4 x ST4.2×15mm Philips Screws (86).
b. Fix the Water Bottle Bracket (43) to the Front Post (11) using 2 x ST4.8×15mm Philips Screws (88).
c. Attach the Left Handle Bottom Cover (24) and Right Handle Bottom Cover (25) to the Left and Right
Action Arm (12 & 13).
d. Fix the Left Footplate Bar Cover (26) and Right Footplate Bar Cover (27) into the position shown in
the diagram using 2 x ST4.2×15mm Philips Screws (86).
13
27
26

The free area must be at least 0.6m greater than the training area. This is a space where you can safely
dismount, without obstruction, in case of an emergency. Where two pieces of equipment are positioned
adjacent to each other the free area may be shared.
Only one person should be within the training area when the equipment is in use.
0.6m
(Free area)
0.6m
(Free area)
0.6m
(Free area)
Training area
1.3m
Workout Area
0.6m
(Free area)
14

85% to Max
65% to 85%
55% to 65%
Up to 55%
Tailor your exercise program according to your physical condition. If you have been inactive for several
years, or are overweight, you must start slowly and increase your time on the equipment; a few minutes per
workout increase is advisable.
Initially, you may be able to exercise only for a few minutes in your target zone, however, your aerobic fitness
will improve over the next six to eight weeks. Don’t be discouraged if it takes longer. It’s important to work at
your own pace.
Please remember these essentials:
• Have your doctor review your training and diet programs to advise you of a workout routine you should adopt.
• Begin your training program slowly with realistic goals.
• Monitor your pulse frequently. Establish your target heart rate based on your age and condition.
• Set up your equipment on a flat even surface with adequate training area, as prescribed in this manual.
Exercise intensity
To maximize the benefits of exercising, it is important to exercise at an appropriate intensity. The intensity level
can be found by using your heart rate as a guide. For effective aerobic exercise, your heart rate should be
maintained at a level between 65% and 85% of your maximum heart rate as you exercise. This is known as
your target zone. You can find your target zone in the table below.
200
180
160
140
120
100
80
25 30 35 40 45 50 55 60 70
Age
During the first few months of your exercise program, keep your heart rate near the low end of your target zone
as you exercise. After a few months, your heart rate can be increased gradually until it is near the middle of your
target zone as you exercise.
To measure your heart rate, stop exercising but continue moving your legs or
walking around and place two fingers on your wrist. Take a six-second heartbeat
count and multiply the results by 10 to find your heart rate. For example, if your
six-second heartbeat count is 14, your heart rate is 140 beats per minute.
(A six-second count is used because your heart rate will drop rapidly when you
stop exercising.) Adjust the intensity of your exercise until your heart rate is at the
required level.
Exercise Information
Cardiovascular
performance
Intermediate aerobic
Effective fat burning
Before starting
Beats per minutes (bpm)
15

Aerobic Exercise
Aerobic exercise improves the fitness of your lungs and heart - your body’s most important muscle. Aerobic
exercise is promoted by any activity that uses your large muscles (arms, legs, or buttock, for example).
Weight Training
Along with aerobic exercising which helps get rid of and keep off the excess fat that our bodies can store,
weight training is an essential part of an exercise routine. Weight training helps tone, build and strengthen
muscle. If you are working above your target zone, you may want to do a lower number of reps.
Targeted Muscle Groups
The exercise routine that is performed on the cross trainer will develop the upper and lower body muscle
groups. These muscle groups are highlighted on the muscle chart below.
A: Trapezius
B: Anterior Deltoid
C: Pectoralis Major
D: Serratus Anterior
E: Biceps
F: Abdominal
G: Sartorius
H: Quadriceps
I: Tibialis Anterior
J: Trapezius
K: Posterior Deltoid
L: Triceps
M: Latissimus Dorsi
N: Gluteals
O: Hamstrings
P: Gastrocnemiu
Muscle Chart
Exercise Information
16

Each workout should include the following three parts:
1. A warm-up, consisting of 5 to 10 minutes of stretching and light exercise. A proper warm-up
increases your body temperature, heart rate, and circulation in preparation for exercise.
2. Training zone exercise, consisting of 20 to 30 minutes of exercising with your heart rate in your training
zone. (Note: During the first few weeks of your exercise program, do not keep your heart rate in your training
zone for longer than 20 minutes.)
3. A cool-down, with 5 to 10 minutes of stretching. This will increase the flexibility of your muscles and will help
to reduce post-exercise muscle soreness.
Exercise Frequency
To maintain or improve your fitness, plan three workouts each week, with at least one day of rest
between workouts. After a few months of regular exercise, you may complete up to five workouts each
week, if desired. Remember, the key to success is make exercise a regular and enjoyable part of your
everyday life.
Suggested Stretches
For a correct warm up, see the following basic stretching exercises. Move slowly as you stretch, never
bounce.
Toe touch stretch
Stand with your knees bent slightly and
slowly bend forward from your hips.
Allow your back and shoulders to relax
as you reach down towards your toes as
far as possible.
Hold for 15 counts, then relax
Repeat 3 times.
Stretches: Hamstrings, back of knees and back.
Hamstring stretch
Sit with one leg extended. Bring the sole
of the opposite foot toward you and rest
it against the inner thigh of your
extended leg. Reach towards your toes
as far as possible.
Hold for 15 counts, and then relax.
Repeat 3 times for each leg.
Stretches: Hamstrings, lower back and groin.
Warming up and Cooling down
Exercise Information
17

Inner thigh stretch
Calf/Achilles stretch
With one leg in front of the other, reach
forward and place your hands against a wall.
Keep your back leg straight and your back
foot flat on the floor. Bend your front leg,
lean forward and move your hips toward the
wall.
Hold for 15 counts, then relax.
Repeat 3 times for each leg. To cause
further stretching of the Achilles
tendons, bend your back leg as well.
Stretches: Calves, Achilles tendons and ankles.
Quadriceps stretch
With one hand against the wall for balance,
reach back and grasp one foot with your
other hand. Keeping your bent knee
pointing directly down towards the floor,
gently pull your heel towards your buttock
until you feel a gentle stretch in the target
area.
Hold for 15 counts, and then relax.
Repeat 3 times for each leg.
Stretches: Quadriceps and Hip muscles.
Sit with the soles of your feet together
and your knees outwards. Pull your feet
towards your groin area as far as
possible, and push your knee down
towards the ground.
Hold for 15 counts, and then relax.
Repeat 3 times.
Stretches: Quadriceps and Hip muscles.
Exercise Information
18

Exercise Information
Console Operation
RECOVERY Key:
This function is used to test your recovery after
workout. Press this key and hold the hand pulse
sensors. The console will count down 60 seconds
and a value of F1 to F6 will be displayed.
F1means good recovery.
Note: You need to have your pulse tested during
the workout before using this function. Otherwise
this key will not work.
MODE Key:
●Press to switch display from SPEED to RPM, to
DIST to ODO during workout.
●To switch the functions that need to input
desired value under workout mode
RESET Key
●Clear the value to zero when set up workout
mode
+ Key:
●Increases value of selected workout
parameter. During the workout pressing +will
increase the resistance load.
- Key:
●Decrease value of selected workout
parameter. During the workout pressing -will
decrease the resistance load.
START/STOP Key:
●Start & Pause workouts.
●Start body fat measurement and quit the
body fat program.
●When off, press and hold the START/STOP
key for 3 seconds to reset all functions.
Key Functions
Display
Mode
Start/Stop
Recovery
Reset
19
Mobile Phone Holder