Argos HOME 618/9138 User manual

Assembly Instructions - Please keep for future reference
Dimensions
Width - 60cm
Depth - 19.5cm
Height - 121.5cm
Important
Version 2 Date: 04/10/16
7 Tier CD DVD Media Unit
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
- Please read these instructions fully before starting assembly
618/9138
606/8345
609/9163

1
Safety and Care Advice
Important –Please read these instructions fully before startingassembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Handy Hints
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Regularly check and ensure
that all bolts and fittings are
tightend properly.

Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline:
Argos = 0345 6400800
2
Left panel (18.9 x 120cm)
1Right panel (18.9 x 120cm) 2Front side panel x 2
(4.5 x 120cm)
3
Top panel (60.1 x 19cm)
4
Support panel (56.8 x 14.5cm)
6
Shelf panel x 5 (56.8 x 14.5cm)
7
Front panel (47.7 x 4.5cm)
8
Bottom front panel (47.7 x 4.5cm)
9
Back panel (118.2 x 59.4cm)
10
Bottom panel (56.8 x 15.5cm)
5
Finished front edge

A B C
D E F
3
Ruler - Use this ruler to help correctly identify the screws
Tools required
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Phillips screwdriver
(medium & large)
Small
hammer
Ruler/tape
measure
Drill
Eye protection
(when using a
hammer or glue)
The screws length is measured from the head to the point (30mm screw shown).
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Components - Fittings
Shelf support x 20
30mm Dowel x 24 15mm Locking nut x 639mm Locking pin x 6
Nail x 24 Support cover x 20
G H I
14mm Screw x 2
Wall strap x 2
Wall plug x 2
x 2
(This screw is
included in the
wall strap bag)
7mm Suitable drill bit
(for use with wall plug)
Pencil

4
Assembly Instructions
Step 1
Fitting dowels and
locking pins
b:
a:
c:
a: Insert Dowels into
the Right panel and
Left panel .
A
2
1
c: Carefully locate the
Front side panel onto
the Right panel and
Left panel .
3
2
1
Screw Locking pins
into the Right panel
and Left panel .
B
2
1
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
b: Insert Dowels into
the Front side panel .
A
3
Continued on next page.
A
A
B
B
B
B
A
2
1
A
A
A
A
B
3
3
1
3
2
X 2

Assembly Instructions
Step 1 - continued
5
e:
d:
f:
f: Carefully locate the
Bottom front panel
onto the Bottom panel .
9
5
e: Insert Dowels into
the Front panel and
Bottom front panel .
A
8
9
d: Insert Dowels into
the Support panel and
Bottom panel .
A
6
5
A
A
A
A
AA
A
A
A
A
A
A
65
8
5
9
9

6
Assembly Instructions
Step 2
a:
b:
a: Carefully locate the
Front panel , Support
panel and Bottom
panel onto the Left
panel .
8
6
5
1
Insert 2 Locking nuts
into the Support panel
and Bottom panel .
C
Use a screwdriver to turn
Locking nuts clockwise
to lock.
C
b: Carefully locate the
Right panel onto the
unit.
2
Insert 2 Locking nuts
into the Support panel
and Bottom panel .
C
Use a screwdriver to turn
Locking nuts clockwise
to lock.
C
Attaching left and right
panels
6
5
6
5
C
6
5
8
6
5
8
C
C
C
1
2
1
C
C

Assembly Instructions
7
a:
Step 3
b:
a: Screw Locking pins
into the Top panel .
B
4
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
b: Carefully locate the
Top panel onto the
unit.
4
Insert 2 Locking nuts
into the Left panel and
Right panel .
C
Use a screwdriver to turn
Locking nuts clockwise
to lock.
C
Attaching top panel
1
2
C
B
C
C
B
4
4
1
2
B

8
Assembly Instructions
Step 4
Attach back panel
using nails .
D
10
Fixing back panel
Important:
The unit MUST
be ‘square’ when
back is attached.
10
D
Unfinished back surface

Warning:
In order to prevent
overturning, this
product must be
used with the wall
attachment device
provided.
9
Assembly Instructions
Step 5
With help, move this
product
into position.
Fixing to wall
Use Screws(2 pcs) to
fix Wall straps(2 pcs)
onto the unit.
Mark fixing holes on wall
and remove this product.
Drill 2 holes and insert
Wall pulgs(2 pcs) .
Reposition this product
and fix wall straps using
Screws(2 pcs) .
Warning:
Before drilling,
check wall for
hidden pipes
and cables.
Warning:
This product is
heavy.
Lift with care.
G
I
H
I
Top panel
wall
G
H
I
II I H
Note: Wall plugs supplied are
for solid wall only.
be used for your wall, seek
professional advice if in doubt.