Argos Jenson Mirror User manual

Spare Parts
Visit: www.argos-support.co.uk
Email: [email protected]
Call: 0330 016 1114
Customer Support
Call: 0345 640 2020
Issue 1 - 08/12/20
Jenson
Mirror
940/0371

Safety
Important - Please read these instructions fully before starting assembly
• WARNING: To prevent
possible overbalancing this unit
must be secured to a wall using
the 2 overbalance protector kits
supplied.
• A unit that is allowed to topple
can cause serious or fatal injury.
In addition to wall fixing the unit,
place heavy items on the lower
shelves, do not put any heavy
objects on top of the unit and
never allow children to climb or
hang on drawers, doors or
shelves.
• Refer to guide after section 18
for wall fixing information.
Care Advice
• Check you have all the
components and tools listed on
relevant pages.
• Remove all fittings from the
specified plastic bag and
separate them into their groups.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Assembly videos are
available throughout
these instructions by
scanning in the QR
codes.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean with a damp cloth.
• Warning: This unit weighs
approximately 34kgs.
Please lift with care.
• Assembly to be carried out by
a competent adult only.
• During assembly children
should be kept away from the
product due to possible risk of
injury.
• Installation shall only be
carried out exactly according to
the manufacturer’s instructions -
otherwise a safety risk can
occur if incorrectly installed.
• Do not use this item if any
components are missing or
damaged.
• Regularly check all fastenings
to ensure they are properly
tightened.

Cabinet Panels Please remove protective film from any gloss panels
459.5 x 29cm
DF-00023102
1137.1 x 28.8cm
DF-00023104
2137.1 x 28.8cm
DF-00023105
556.1 x 5.8cm x 6
DF-00023103
XDF-00022219
3135.3 x 58.7cm
DF-00023802
655.6 x 35.5cm x 3
DF-00022241
754.9 x 14cm x 6
DF-00022244
854.9 x 8.7cm x 3

Drawer Panels Note: the internal drawer panels are grey
955.6 x 9.6cm
DF-00023808
11 26 x 6.8cm
WRP-00000473
10 26 x 6.8cm
WRP-00000474
WRP-00000475
12 52.85 x 6.8cm
TDF-00022552
13 53.95 x 25.1cm

Fittings Use these drawings to
correctly identify the fittings
F171GY
Bag 1
Bag 2
Hx 2 Jx 4
A
F901
F22
Ax 16 Cx 16
I
F3
F74
x 2
F
F646
x 4
A
F901
Ax 2
D
F73
x 4
G
F639
x 4
Bx 16
F900
Bag 3 Bag 4
Bag 5
L
F52
x 24 Mx 18
F63
F51
x 25
E
K
F464
x 5
Qx 1 Rx 1 L
F52
F259
F258
x 2
Px 6
F109
Nx 6 Ox 6
F506
F507

Fittings
F474
FST
Tx 2
F307
Ux 2
Shoe Boys
Sx 3
c
c
cd
e
a b
dd
ee
Tools
Only used for
drilling walls

1
Finished
front edge
www.youtube.com/watch?v=yG4x�JJeSg
Fitting Ball Bearing Runners
Dx 4
Ux 2
Finished
front edge
2
1
2nd hole
A B
2nd hole
A B
Bag 1
A
F901
F22
Ax 16 Cx 16 F
F646
x 4
D
F73
x 4
Bx 16
F900
F51
x 25
E

2
3
Cx 4
2
1
Bx 4
2
1
4
2
1
Ax 12

5
6
2
1
Nx 6
2
1
S
eIMPORTANT:
Carefully snap off
these fittings from
the Shoe Boys
x 6
Shoe Boys
Sx 3
c
c
a b
dd
ee
Bag 4
Px 6
F109
Nx 6 Ox 6
F506
F507

7
8
x 6
5
Finished
front edge
Finished
front edge
Finished
front edge
Finished
front edge
Finished
front edge
Cx 12 Bx 12
1
5
Finished
front edge 5
5
Finished
front edge
5
5
5
9
1
5
5
5
5
5
5
x 4
x 2
IMPORTANT:
Support panels until other
end panel is fitted in the
next step

Finished
front edge
10
11
12
2
x 4
Finished
front edge
Ax 4
Tx 2
Only use 1 Screw
to fit each Bracket
4
4
x 2

Finished
front edge
13
14
Qx 1 Lx 2
Bag 5
Qx 1 Rx 1 L
F52
F259
F258
x 2
4
4
x 4

15
16
www.youtube.com/watch?v=FeaI6541z7o
Squaring up a Chest and fitting the Back Panel
A = B
Make sure measurement A and B
are the same before attaching the
back panel
B
B
A
A
3
Ex 25

17
3
Fx 4
‘Tap’

18
Tx 2
WARNING!
In order to prevent overturning
this product must be used with the
2 wall attachment devices provided
See the next section for a
guide to wall mounting and
fixings
Slide the Brackets against the wall. Fit the 2nd screws supplied
with the Brackets into the underside of the Top panel.
Mark the slot at the back of the Brackets for drilling into the wall.
Wall fixings are not supplied as they will need to suit the wall type.
Note: Take care when drilling the wall that you do not drill
into any pipes, wires etc.
If in doubt, consult an expert.
3
Top

Important note:
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
If plastic wall plugs
are supplied with your
product:
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect fixings is the
responsibility of the installer.
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well fitted and are a tight fit in the
drilled hole.
Types of walls You can use one of the following types of wall plug if your
walls are made of brick, breeze block, concrete, stone or wood.
Generally aerated blocks should not
be used to support heavy loads, use
a specialist fitting in this case. For light
loads, general purpose wall plugs can
be used.
For use with plasterboard partitions or
hollow wooden doors.
For use with walls stuck with
plasterboard. The hammer fixing allows
it to be fixed to the wall rather than the
plasterboard. Always check the fixing
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions.
For use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
No.1 “General Purpose” wall plug No.3 “Cavity Fixing” wall plug No.5 “Hammer Fixing” wall plug
No.2 “Plasterboard” wall plug
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.6 “Shield Anchor” wall plug
Heavy loads
A Guide to Wall Mounting & Fixings
Care &
Maintenance
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.

20
19
FST
Shoe Boys
Sx 3
c
c
cd
e
a b
dd
ee
c
d
IMPORTANT:
Carefully snap off the rest
of the fittings from the
Shoe Boys to use later
6
x 3
Shaped
front edge
Ox 6
Px 6
Warning:
Glass! Handle
with care
Bag 4
Px 6
F109
Nx 6 Ox 6
F506
F507

22
23
x 3
x 3
Mx 3
Finished
front edge
8
8
21 b
Sx 3 Lx 9
6
x 3
Bag 3
L
F52
x 24 Mx 18
F63

25
26
Mx 3
x 3
x 3
7
IMPORTANT:
Support this panel
until the Shoe Boy is
fitted in the next step
Sx 3
Lx 9
a
x 3
Finished
front edge
7
24

28
S
d
Lx 6 x 6
27
Mx 6
x 3