Argos Lamberto Ottoman TV Bed User manual

Assembly Instructions - Please keep for future reference
Dimensions (4-6)
Length - 227 cm
Width - 146 cm
Height - 103 cm
Lamberto Ottoman TV Bed
Issue 1 - 11/10/15
496/8870
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call one of the Customer Helplines:
00465430 800 (For order problems,incorrect product or missing/damaged parts).
01626 879 158 (Only for problems with TV Installation, Electrical System or TV Lift not working).

Safety and Care Advice
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Assembly requires 2 people.
Do not fully tighten bolts until
the whole bed is assembled.
Do not over tighten the nuts to
avoid causing damage to the
threads.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers and
Allen keys.
Dispose of all packaging
carefully and responsibly.
Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Important Ottoman Safety Warnings
·Caution.This bed frame uses a pressurised mechanism.
·Always operate with caution and always use the fabric hand strap to lift & lower the ottoman
frame and only as shown illustrated in the assembly instructions.
·You must ensure the mattress is on the frame before lifting the mechanism - failure to do so may
result in injury.
·Please ensure children and pets are kept away from the bed when lifting the ottoman frame
· If removing the mattress, make sure that the frame is secured as it could flip open.
· Only use the storage compartment when the frame is fully raised in the ‘up’ position.
·No children or animals to be left unattended when the frame is in the ‘up’ position.
· Do not remain on the bed whilst the lifting mechanism is in use.
·Beware of Entrapment - Keep both hands clear of mechanism when moving the frame up or down.
·When lifting the bed remove all bedding except the fitted sheet.
ENSURE MATTRESS IS ON
BEFORE LIFTING

2
0345 6400 800
Side rails x2
Fabric Hand Strap
(4-6 - 1930 × 305 x 35mm)
Headboard (4-6 -1460 × 1030mm)
Ottoman Frame (4-6 -1900 × 1370mm)
‘U’ shaped cross bar (4-6 -1390 × 40mm)
Footboard (4-6 -1460 × 770mm)
Fabric base cover
(4-6 -1420 × 1960mm)
Angle Brackets x4
8Hinge Mechanisms x1 pair
8a 8b

3
0345 6400 800
B C
D E F
x1
x38
x44
x4
A
F
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
0
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150
1 2 3 4 5 6
Ruler/tape
measure
Components - Fittings
G
K
N
H
L
P
J
M
x32 x6
Nut (M8) x6
Phillips screw-driver
Spanner
Spanner
(supplied)
Allen key
(supplied)
T
Cable Management Clip
TV INSTALLATION KIT
Flange Lock-Nut Mattress Stopper
Cable Clip Cable Tie
Cable Management Tube
Allen Screw (M8x30mm)
Screw (4x50mm)
Spring Washer (for M8 screw)
Allen Key (for M8 screws)
Flat Washer (for M8 screw)
For holding nuts (F&H) x1 x2 x2
x3 x3
x1 x1 x1
Screw-Washer set (M8x25mm)
Counter-Sunk Screw (M6x12mm)
Counter-Sunk Screw (M4x12mm)
Allen Key (5mm)
Allen Key (4mm)
Allen Key (2.5mm)
x4
x4
x4
x1
x1
x1
Allen Screw (M8x45mm)
R
x1Spanner for Nut (M6)
Mains Power Lead (3 metre)
Q
S

Assembly Instructions
4
R
F
I
T
H
E
R
E
BOLTS SHOULD BE IN CENTRE
OF LONG HOLES
Opening from left side
E
A
C
D
At this stage you can
choose to have the
ottoman frame lifting from
either side as shown.
Attaching Hinge
Mechanism
To lift from the left side,
assemble hinge
mechanisms in the
location shown.
For Left Opening
Secure the hinge
mechanisms to the
headboard and
footboard using screw
, spring washer
and flat washer .
HEADBOARD
FOOTBOARD
IMPORTANT
Use blue colour fixing
holes for left side opening.
IMPORTANT
Use blue colour fixing
holes for left side opening.
AC
D
8
8
FIT TO BLUE LABELS
R
F
I
T
H
E
R
E
L
F
I
T
H
E
R
E
R
F
I
T
H
E
R
E
L
F
I
T
H
E
R
E
R
F
I
T
H
E
R
E
R
F
I
T
H
E
R
E
L
F
I
T
H
E
R
E
L
F
I
T
H
E
R
E
R
F
I
T
H
E
R
E
L
&
R
F
I
T
H
E
R
E
L
&
R
F
I
T
H
E
R
E
R
F
I
T
H
E
R
E
L
F
I
T
H
E
R
E
L
F
I
T
H
E
R
E
BLUE
BLUE
a
b
Note: Use the holes
colour coded blue.

Assembly Instructions
5
L
F
I
T
H
E
R
E
Opening from right side
E
A
C
D
BOLTS SHOULD BE IN CENTRE
OF LONG HOLES
FIT TO RED LABELS
RED
RED
R
F
I
T
H
E
R
E
L
F
I
T
H
E
R
E
R
F
I
T
H
E
R
E
L
&
L
F
I
T
H
E
R
E
L
F
I
T
H
E
R
E
R
F
I
T
H
E
R
E
R
F
I
T
H
E
R
E
R
F
I
T
H
E
R
E
L
&
R
F
I
T
H
E
R
E
L
F
I
T
H
E
R
E
L
F
I
T
H
E
R
E
L
F
I
T
H
E
R
E
R
F
I
T
H
E
R
E
R
F
I
T
H
E
R
E
a
b
Attaching Hinge
Mechanism
To lift from the right side,
assemble hinge
mechanisms in the
location shown.
For RightRight Opening
Secure the hinge
mechanisms to the
headboard and
footboard using screw
, spring washer
and flat washer .
HEADBOARD
FOOTBOARD
IMPORTANT
Use red colour fixing holes
for right side opening.
IMPORTANT
Use red colour fixing holes
for right side opening.
AC
D
8
8
Note: Use the holes color
coded red.

Assembly Instructions
6
10mm
Note: Do not tighten fully.
Leave 10mm protruding
as in the diagram.
a: Loosely insert screws
with spring washers
and flat washers
into each side of
headboard and footboard
and .
A
CD
A
a:
C
D
b: Hang the side rail
brackets onto screws
behind the flat washers.
b:
A

7
a:
b:
Assembly Instructions
b: Fit the 'U' shaped cross
bar to centre of side
rails using screws .
Note: The fixing hole
locations are marked on
K
ACD
E
ACD
a: Fit angle brackets
into each corner, using
fixings and .
Note: Do not fully tighten
at this stage.
Assembling Bedstead
Make sure the frame is
straight and square.
When all the bolts are in
place, make sure the frame
is still square and then fully
tighten all screws.
K
the side rails.

8
Assembly Instructions
Fitting Base Cover
With help, carefully turn
the frame on its side and
attach fabric base cover
to the bottom of the
footboard with the velcro
tape.
Make sure fabric is fixed
evenly all round.
! Warning:
The frame is heavy. Lift
evenly at each end taking
care not to twist it.
side rails, headboard and

9
b:
a:
c:
Assembly Instructions
Prepare To Install TV
To Raise The
Mechanism
Before fitting the
television to the TV lift
please check below:
Depth 7 cm
=
Maximum dimensions of
TV that can be used in
this bed:
Note: The TV is not
supplied with the bed, it
is purchased separately.
The TV mounting bracket
(x) is factory fitted to
column bracket (y). The
bracket (x)can be turned
upside down to give more
flexibility in adjustment -
see Step 7 & 8 for more
information.
a:
b: Gently press down on
the top of the TV lift
handle with the palm of
your hand until it comes
to a stop.
Lift the lid on top of
footboard .
c: Release pressure and
the lift will rise smoothly
to the top. Do not try to
pull it up.
Width = 80 cm
Height = 44 cm
Maximum weight of TV
that can be used in this
bed = 6.5 Kg
(y)
(x)