Argos Summerton 137/6300 User manual

Step 7
Summerton Ottoman Bedstead
If you need help or have damaged or missing parts, call the Customer Helpline: 01992 450333
Assembly Instructions - Please keep for future reference
Important - Please read these instructions fully before starting assembly
Dimensions
Width x Depth x Height
208cm x 144cm x 35/97cm (Double)
218cm x 160cm x 35/97cm (King)
137/6300
134/2884
128/1938
129/5450
Issue 1 - 27.03.12

Safety and Care Advice
Important–Please read these instructions fullybefore starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals away
from the work area, small parts if
swallowed could cause choking.
• Make sure you have enough
space to layout the parts before
starting.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Assembly requires 2 people.
• Do not fully tighten bolts until
the whole bed is assembled.
• Do not overtighten the nuts to
avoid causing damage to the
threads.
• We do not
recommend the
use of power
drill/drivers for
inserting bolts,
or screws as this could damage
the unit. Only use hand screw-
drivers and Allen keys.
• Dispose of all packaging
carefully and responsibly.
.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
stunrostlobesooloneraereht
. .tinusihtno
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
1

Components If you have damaged or missing components,
call the Customer Helpline: 01992 450333
2
1 Right side rail
2 Left side rail 6 Gas strut x 2
8 Mattress support x 2
5 Hinge x 2
3 Headboard
4 Footboard
7 Base panel
13 Side rail x 2
14 Centre rail x 1
16 Bottom centre rail x 1
12 Front frame rail x 1
18 Support rail x 2
23 Base support x1
11 Back frame rail x 1
22 Belt
15 Slats x 28 (double)
x 30 (king)
Please check you have all the parts listed below
21 Side slat caps x 28
(double) x 30 (king)
20 Centre slat caps x 14 (double)
x 15 (king)
9 Wooden foot x 4
17 Support rail x 4
10 Long leg x 2
19 Short support leg x 1

Components - Fittings
3
Please check you have all the fittings listed below
Tools required
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
A
55mm M6 Bolt x 2
45mm M4 Wood screw x 16 M6 Flat washer x 12
5mm Allen key x 1 (supplied) 4mm Allen key x 1 (supplied)
Nut x 4
B
15mm M6 Bolt x 6
C
D E
H
20mm M6 Bolt x 22
I
35mm M6 Bolt x 1Plastic foot adjuster x 2
Plastic cap x 1
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
F
Flat washer x 8
K
25mm M6 Bolt x 4
Phillips screwdriver
G
J
40mm M8 Bolt x 8 30mm M4 Screw x 4
N
M
Spanner x 1 (supplied)
Spring washer x 8
L

Assembly Instructions
4
Step 1
3
Attaching feet
a. Attach 2 x wooden feet
to the underside of
the headboard using
screws as shown.
9
3
D
b. Attach 2 x wooden feet
to the underside of
the footboard using
screws as shown.
9
4
D
9
3
D D
4
4
Please note: There are
no guide holes for the
screws D on the head-
board 3 or footboard 4
Position the feet
approximately 1” (2.5cm)
from the edge and
screw into position.
D
3 4
a:
b:
9
D D
9
D D
9
D D

Assembly Instructions
Step 2
4
Assemble footboard
a: Attach the base support
to the footboard
using bolts and
washers as shown.
b: Attach the support
rails to the footboard
as shown using
screws .
17
423
5
A
F
D
F
F
A
A
D
D
D
D
a:
c:
4
23
b:
4
17
17
c: Attach the support
rails to the headboard
as shown using
screws .
17
D
3
D
D
D
D
3
17
17
Please note: There are no
guide holes for screws D
On the footboard or
headboard .
Position support rails
between the guidelines
and screw into place.
D
17
4
3

Assembly Instructions
6
Step 3
2
1
3
MLK
LK
L
K
L
K
M
M
Attaching side rails
a: Position left side rail
adjacent to headboard
so that the holes in the
headboard line up with
the bracket on the side
rail.
Secure in place using 2
screws , spring
washer and washer .
2
3
M
L K
Secure in place using 2
screws , spring
washer and washer .
M
L K
a:
b:
3
M
b: Position right side rail
adjacent to the headboard
so that the holes in the
footboard line up with
the bracket on the side
rail.
1
3
Note: Ensure that foot-
board, headboard and side
rails are square.
c: Position left side rail
adjacent to footboard
so that the holes in
the footboard line up
with the bracket on the
side rail. Secure in place
using 2 screws .
Position the right side
rail (1) adjacent to
footboard (4) so that the
holes in the footboard
line up with the bracket
in the side rail. Secure in
place using 2 screws .
2
1
4
4
M
M

Assembly Instructions
Step 4
7
c: Attach the support rails
to the side rails &
using screws as
shown.
18 1
2
N
b: Attach the bottom
centre rail to the
headboard and foot-
board using bolts
and washers as shown.
3
4
16
I
F
Assemble base
a: Attach the short
support leg to the
underside of the bottom
centre rail using bolt
. Insert cap .
19
16
HJ
3
4
16
16
19
1
I
F
I
F
H
J
a: b:
c:
N
N
N
18
18
2
1
2
N

Assembly Instructions
Step 5
Step 6
8
Inserting base panel
Carefully insert the base
panel as shown,
making sure the joins are
not stressed or torn.
Attaching hinges
a: Attach the hinges to
the side rails &
using 4 x bolts as
shown.
b: Attach the gas struts
with the thinner tube
facing down towards the
bed base. Secure in place
to the top of the hinge
using nut as shown.
c: Secure gas strut to
the bottom of the hinge
using nut as shown.
7
7
C
C
C
C
5
1 2
6
6
5
5
6
5
1
C
E
E
E
6
6
5
5
5
b:
a:
c:
2
E

Assembly Instructions
Step 7
9
Frame assembly
a: Attach belt to front
frame rail .
b: Connect the side rails
back frame rail , front
frame rail , and centre
rail using bolts and
washers as shown.
The side rails 13 should
be positioned with the row
of 3 holes to the rear.
13
13
C
F
C
F
C
F
C
F
C
F
C
C
C
C
C
C
C
C
11
12
12
22
14
c: Flip the assembled
frame over.
Connect the mattress
supports to the back
frame rail using bolts
as shown.
C
11
8
d: Attach the long legs
to the underside of the
frame using bolts as
shown. Insert the plastic
foot adjusters .
C
G
10
G
G
b:
a:
c:
d:
11
13
12
22
8
13
14
11
13
12
13
14
14
10
10
22
12
8
11
C
FC
F