Argos 603/7840 User manual

7
Assembly is complete.
Width - 47cm
Depth - 55cm
Height - 96cm
Assembly Instructions - Please keep for future reference
Dimensions
Paris Chair
c:
d:
c:
After the sitting test,
re - tighten bolts again,
if any adjustment needed.
d:
It is highly recommend
to re - tighten all the bolts
again after using the chair
for 7 days.
Note : Please keep the
allen key to re - tighten
all bolts again when
required.
Assembly Instructions
603/7840
603/7857
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
Issue 1 - 9/08/16
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800

1
Step 2
e:
Assembly Instructions
Screw the lock seats
with hand screw driver
by following the pre drilled
holes.
E
De:
a:
Tighten all bolts.
Note : Stand the chair on
a level floor.
a:
b:
Sit on the chair to
the legs.
6
Pre-drilled
hole
E
D
b:
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Care and maintenance
• Check you have all the
components and tools listed on
page 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
• Maximum safe weight of
user: 110 Kgs.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts.
• Reguraly check and ensure
that all bolts and fittings are
tightend properly.
• Do not stand or put weight on
the product during assembly,
this could cause damage.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Do not stand on the chair.
• Do not use the chair as step
ladder
• Assemble the item as close
to its final position (in the same
room) as possible.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.

2
Components - Parts
Please check you have all the parts listed below
Chair back x 1 Seat x 1
12
3
4Right side rail x 1Front leg frame x 1
BACK
5
c:
A
B
C
Assembly Instructions
d:
d:
c:
Stand the chair on a
floor. Insert bolts with
spring washers and
washers through side
rails holes into front leg
frame screw all bolts
by using ball allenkey .
3
A
G
B
C
Place the seat pad
on the table. Put the
chair frame on top of the
seat back.
2
Insert screw into
the pre - drilled holes on
the righ leg rail and
left leg rail using a
screwdriver.
F
6
BACK
6
F
5Left side rail x 1 6Right leg rail x 1
7Left leg rail x 1
7
1
34
5
6
7
2
6
7
BACK
Note :The quantities below are the correct amount to complete the assembly of 1 chair.
If you have damaged or missing components, call the
Customer Helpline:
Argos = 0345 6400800

Components - Fittings
Please check you have all the fittings listed below
Note :The quantities below are the correct amount to complete the assembly of 1 chair. In some cases more
fittings may be supplied than are required.
65 mm Bolt x 8
B
Spring washer x 8
C
D
Washer x 8
F
Lock seat x 2 38mm Screw x 4
A
E
19 mm Screw x 4
3
G
Ball allenkey x 1
Tools required
Phillips screwdriver
(medium & large)
Assembly Instructions
Step 1
a:
4
A
a:
b:
b:
Put left side rail into
left side hole of the chair
back and right side rail
into right side hole.
Insert bolt with spring
washers and washers
through side rails holes
into the chair backs.
Screw all bolts by using
ball allenkey .
B
C
G
Do not fully tighten.
Fit the front leg frame
onto the right and left
side rails and right
and left leg rails .
3
4
4
5
1
pre - drilled hole
A
B
C
Right side rail
Left side rail
Insert screw into the
pre-drilled holes in the
right leg rail and
left legs rail tighten
(although not fully) with
a screwdriver.
7
F
5
F
R
L
BACK
BACK
6
6 7
6
74
5
BACK
4
5
6
7
1
3
Ruler - Use this ruler to help correctly identify the screws
100 20 30 40 50 60 70 80 90 100
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
The screws length is measured from the head to the point (30mm screw shown).