Argos Hearts 2595386 User manual

Assembly Instructions - Please keep for future reference
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Argos Customer Helpline: 03456 400 800
Hearts 2595386
Stars 4591151
Hearts
Stars
Issue 3 - 23-09-2015
Mia Hearts / Stars 4+2 Drawer Chest
Dimensions
Width
Depth
Height
:
:
:
350272
88.5 cm
43.3 cm
90.0 cm

!Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
1
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not recommend the use
of power drill/drivers for
inserting screws, as this could
damage the unit. Only use hand
screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page
with these instructions for
future reference.

Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call
the Argos Customer Helpline: 03456 400 800
2
350272-03
2
(81,6 cm x 38,3 cm)
Side, left
13
(73,4 cm x 9,8 cm)
Drawer back, large
15
(74,4 cm x 34,7 cm)
Drawer bottom, large
11
(35 cm x 9,8 cm)
Drawer side, right/left
4
x
1
(88,5 cm x 43,3 cm)
Top
3
(81,6 cm x 38,3 cm)
Side, right
4
(88,5 cm x 4,4 cm)
8
(76,7 cm x 9,5 cm)
Front rail
10
(76,1 cm x 14,5 cm)
Drawer front, large
7
(76,7 cm x 7 cm)
5
(82,2 cm x 39,5 cm)
Back
4
x
4
x
4x
2
x
12
x
6
(80 cm x 1,7 cm)
H-Profile
9
(37,9 cm x 14,5 cm)
Drawer front, small
12
(33,4 cm x 9,8 cm)
Drawer back, small
14
(34,4 cm x 34,7 cm)
Drawer bottom, small
2
x
2
x
2
x

Components - Fittings
Please check you have all the panels listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
3350272-04
6 ø7.8 x 40mm Wooden dowel x
Aa Ab
ø6 x 30mm Wooden dowel x 24
Cb
ø5 x 8, cc34mm Bolt x 18
Ca
ø15 x 10.5mm Cam x
18 1.2 x 15mm Nail x
Di
25
Hk
12
M4 x 9mm Screw x
Kb
ø5.8 x 8mm Screw x
28
Sk
12 245 x 17 x 10mm Drawer runner x
17060 16040 90 15013070 120100 14011050 803020100
Ruler - Use this ruler to help correctly identify the screws
Tools required
Flatblade screwdriver
(Medium)
Hammer Phillips screwdriver
(Medium & large)
Back fitting w. ø3.5 x 15mm Screw x
Fi
12
ø4 x 25mm Screw x
Jb
16
ø3 x 35mm Screw x
Bp
24
2
Vl
44 x 23 x 23mm Angle x
Ko
8
ø4,2 x 9,5mm Screw x
Wb
Support for drawer runner x
2
Wall strap and instruction x 1
Fh
ø10 x 9mm Spacer x
Nu
6
Kf
6
ø5.8 x 19mm Screw x
ø3.5 x 14mm Screw x
Je
4

Assembly Instructions
Fix the posts
4
onto the
sides
2
and
3
using
screws
Jb
into the holes
indicated.
The top of the posts
4
and
the sides
2
and
3
must
be ush.
Step 1.1
Assembly of the chest.
Step 1
Knock the dowels
Aa
into the holes indicated
on the sides
2
and
3
using a small hammer.
Screw the bolts
Cb
into
the holes indicated on the
sides
2
and
3
.
Step 1.2
4
350272-05
Cb
ø5 x 8, cc34mm Bolt x 2
ø4 x 25mm Screw x
Jb
16
4
ø7.8 x 40mm Wooden dowel x
Aa
Jb
Jb
Cb
Cb
Aa
Aa
Aa
Aa
Jb
Jb
Jb
Jb
Jb
Jb
Jb
Jb
Jb
Jb
3
4
4
4
4
2
84
4
2
4
5
1
3
4
7
3
2
6
5
44
32
4
Jb
Jb
Jb
Jb
Jb

Assembly Instructions
Slide the top of the
drawer runners
Sk
backwards. You can
identify the front end of
the drawer runner
Sk
by
the two M4 holes. See
details.
Place the Spacers
Nu
as
shown, and x the front
end of the upper drawer
runners
Sk
to the sides
2and 3using screws
Kf
through the holes
number 2 and 11 as
indicated.
Fix the front end of
the rest of the drawer
runners
Sk
to the sides
2and 3using screws
Kb
through the holes
number 2 and 11 as
indicated.
See details.
Step 1.3
350272-06
5
3
Sk
Kb
Note the hole!
Bottom end of
right hand side
Front end
Sk
Front end
Front end
Sk
10 245 x 17 x 10mm Drawer runner x
Kb
ø5.8 x 8mm Screw x
16
Sk
Sk
Kb
Kb
Sk
Sk
Sk
Kb
2
ø10 x 9mm Spacer x
Nu
4
Kf
4
ø5.8 x 19mm Screw x
Kb
Kb
Sk Sk
Nu
Nu Kf
Kf
Sk
Sk
Sk
Sk
Kb
Sk
Nu
Nu
Kf
Kf
Kb
Kb
Sk
Kb
Hole no.
11
Hole no. 11
Hole no. 2
Hole no.
2
Hole no.
11
Hole no. 11
Hole no.
2
Hole no. 2

Assembly Instructions
Slide the top of the draw-
er runners
Sk
forwards.
Place the Spacers
Nu
as
shown, and x the back
end of the upper drawer
runners
Sk
to the sides
2and 3using screws
Kf
through the holes
indicated.
Fix the back end of
the rest of the drawer
runners
Sk
to the sides
2and 3using screws
Kb
through the holes
indicated.
See details.
Step 1.4
Screw the bolts
Cb
into
the holes indicated on the
top
1
.
Step 1.5
6
350272-07
Kb
ø5.8 x 8mm Screw x
8
Kb
Kb
Kb
Kb
2
3
ø10 x 9mm Spacer x
Nu
2
Kf
2
ø5.8 x 19mm Screw x
Kb
Sk
Kb
Kf
Nu
Nu
Kf
Kb
Kb
Cb
ø5 x 8, cc34mm Bolt x
4
1
Cb
Cb
Cb
Cb

Assembly Instructions
Fix the drawer runner
supports
Wb
to the top
1
using screws
Je
into the
holes indicated.
Step 1.6
Slide the top of the
drawer runners
Sk
backwards. You can
identify the front end of
the drawer runner
Sk
by
the two M4 holes.
Fix the front end of the
drawer runners
Sk
to the
drawer runner support
Wb
using screws
Kb
through
the holes number 2 as
indicated.
See details.
Step 1.7
Slide the top of the
drawer runners
Sk
forwards.
Fix the drawer runners
Sk
to the drawer runner
support
Wb
using screws
Kb
through the holes
indicated.
See details.
Step 1.8
350272-08
7
1
Sk
2 245 x 17 x 10mm Drawer runner x
Kb
ø5.8 x 8mm Screw x
2
Kb
ø5.8 x 8mm Screw x
2
Wb
Support for drawer runner x
2
ø3.5 x 14mm Screw x
Je
4
Sk
Front end
Front end
Wb
Wb
Je Je
Wb
Je Je
Kb
Sk
Sk Kb
Kb
Kb
1
1
Wb
Wb
Hole no.
2

Assembly Instructions
Place the sides 2and
3onto the back rail 7.
Push cams
Ca
into the
holes indicated on the
back rail 7.
Arrows pointing towards
the sides 2/3.
Turn the cams
Ca
to the
right to x the sides 2
and 3.
Step 1.11
Knock the dowels
Aa
into
the holes indicated on
the back rail
7
using a
small hammer.
Step 1.9
Fix the angles
Vl
using
screws
Ko
into the holes
indicated on the front
rail
8
.
Step 1.10
8
350272-09
Ca
ø15 x 10.5mm Cam x
2
3
2
Ca
Ca
7
Ko
Vl
8
Ko Ko
Aa
Aa
7
Ko
4
ø4,2 x 9,5mm Screw x
2
Vl
44 x 23 x 23mm Angle x
2 ø7.8 x 40mm Wooden dowel x
Aa
Vl

Assembly Instructions
Place the front rail 8
as shown.
Fix the angles
Vl
to the
sides using screws
Ko
.
See detail.
Step 1.13
Place the top 1onto the
sides 2and 3.
Push cams
Ca
into the
holes indicated on the
sides 2and 3.
Arrows pointing towards
the top 1.
Turn the cams
Ca
to the
right to x the top 1.
Step 1.12
350272-10
9
8
Ko
Ko
Ko
4
ø4,2 x 9,5mm Screw x
Ca
3
2
1
Ca
Ca
Ca
ø15 x 10.5mm Cam x
4

Assembly Instructions
Step 1.15
!
Important!
The chest of
drawers is heavy.
Lift with care.
Its recommended that the
chest is xed to the wall.
Use the ttings
Fh
. Follow
the instructions included
with the ttings.
Step 1.14
Place the backs 5into
the rabbet on the top 1
into the H-prole 6and
onto the posts 4.
!
Important!
Make sure the
angle between the
top
1
and the posts
4
is
90° when the backs
5
is
attached.
Fix the backs
5
to the top
1, the posts 4and the
back rail 7
using
nails
Di
.
Use a small hammer.
350272-10
9
8
Ko
Ko
Ko
4
ø4,2 x 9,5mm Screw x
Ca
3
2
1
Ca
Ca
Ca
ø15 x 10.5mm Cam x
4
10
350272-11
Wall strap and instruction x 1
Fh
Di
Di
Di
6
7
5
14
4
Di
5
Distribute equally !Distribute equally !
1
1
1.2 x 15mm Nail x
Di
24

Assembly Instructions
Knock the dowels
Ab
into the holes indicated
on the drawer sides 11
using a smal hammer.
Step 2.2
Fix the drawer sides 11
to the drawer backs 12
and 13 as shown, using
screws
Bp
.
Step 2.1
Assembly of the drawers.
Step 2
350272-12
11
2
x
2
x
Bp
Bp
ø3 x 35mm Screw x
Bp
24
12
11
11
14
12
11
11
4
x
11
11
Ab
Ab
4x
15
13
11
11
10
Ab
ø6 x 30mm Wooden dowel x 24
4x
2
x
11
11
13
11
11
Bp
Bp
9
Ab
Ab

Assembly Instructions
Slide the drawer bottoms
14 and 15 into the
drawer sides 11 .
Step 2.3
Step 2.4
Screw the bolts
Cb
into
the holes indicated on
the drawer fronts 9and
10 .
Step 2.5
Push the drawer fronts
9
and 10
onto the drawer
sides
11
.
Place cams
Ca
into the
holes indicated. Arrow
pointing towards the front.
Turn the cams
Ca
to the
right to x the front.
12
350272-13
Cb
ø5 x 8, cc34mm Bolt x 12
10
Cb
Cb
4
x
11
11
Ca
Ca
10
Cb
Cb
9
9
11
11
2
x
4
x
2
x
Ca
ø15 x 10.5mm Cam x
12
Ca
Ca
4
x
2
x
11
11
14
11 15
11
350272-12
11
2
x
2
x
Bp
Bp
ø3 x 35mm Screw x
Bp
24
12
11
11
14
12
11
11
4
x
11
11
Ab
Ab
4x
15
13
11
11
10
Ab
ø6 x 30mm Wooden dowel x 24
4x
2
x
11
11
13
11
11
Bp
Bp
9
Ab
Ab

Assembly Instructions
Pull out the drawer
runners. Slide the
drawers onto the runners.
Fit and x the lower
drawer rst and work your
way up.
Fix drawers to the drawer
runners using screws
Hk
.
Step 2.7
Step 2.6
!
Important!
Make sure the
angle between the
drawer fronts
9/
10
and
the drawer sides
11
is 90°
before the drawer bottoms
14
and
15
is xed using
Fi
as shown.
To adjust the angle between
the drawer sides and the
fronts push the tting
Fi
sidewards. See details.
350272-14
13
90°
Hk
12
M4 x 9mm Screw x
Hk
Hk
Fi
Fi
4
x
Fi
Back fitting w. ø3.5 x 15mm Screw x
Fi
12
Fi
Fi
Fi
Fi
2
x

350272-14
13
90°
Hk
12
M4 x 9mm Screw x
Hk
Hk
Fi
Fi
4
x
Fi
Back fitting w. ø3.5 x 15mm Screw x
Fi
12
Fi
Fi
Fi
Fi
2
x
No.3 "Shield Anchor" Wall Plug
Heavy Loads
For use with heavier loads such as TV
& HiFi Speakers and Satellite Dishes etc.
No.4 "Cavity Fixing" Wall Plug
For use with plaster board partitions or
hollow wooden doors.
No.5 "Cavity Fixing - Heavy Duty"
Wall Plug
For use when fitting or supporting heavy
loads such as shelving, wall cabinets,
coat racks.
IMPORTANT:
When drilling into walls always check that there are no
hidden wires or pipes etc. Make sure that the screws and
wall plugs being used are suitable for supporting your unit.
Consult a qualified tradesperson if you are unsure.
HINTS:
1) General Rule Always use a larger screw and wall plug if you are not sure.
2) Ensure you use the recommended drill bit to match the wall plug and hole size.
3) Ensure you drill the hole horizontally, do not force the drill or enlarge the hole.
4) Take extra care when drilling high walls, ceilings and ceramic tiles. Ensure the plug is fitting below the ceramic
tile to avoid splitting or cracking.
5) Ensure wall plugs are well fitted and are a tight fit in the drilled hole.
Types Of Walls
You can use one of the following types
of wall plug if your walls are made of
brick, breeze block, concrete, stone,
wood or plaster board.
No.1 "Standard" Wall Plug
General Wall Materials
These come in various sizes and are made
from plastic or sometimes wood fiber.
No.2 "General Purpose" Wall Plug
Aerated / Breeze Block
Generally aerated blocks should not be
used to support heavy loads, use a
specialist fitting in this case.
For light loads, a General Purpose Plug
can be used.
No.6 "Hammer Fixing" Wall Plug
For use with walls stuck with plaster
board. The hammer fixing allows it to
be fixed to the wall rather than the plaster
board. Always check the fixing is secure
to the retaining wall.
CARE & MAINTENANCE
SAFETY
Always check the fitting and
location to ensure your safety in
and around the home.
FITTING
From time to time check the fitting
to ensure the wall plugs or screws
do not become loose.
Wall Mounting & Fixings
A Guide to