Argos Grafton 360/9109 User manual

Grafton 5ft Bed
360/9109
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800
Important – Please read these instructions fully before starting assembly
Issue 1 - 24/11/14
Dimensions
Width - 163,5cm
Depth - 214,5cm
Height - 120cm
352/2365

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: if required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
.Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
.
plastic bags and separate them
into their groups.
Keep children and animals
.
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
.
space to layout the parts before
starting.
Do not stand or put weight on
.
the product, this could cause
damage.
We do not
.
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Parts of the assembly will be
.
easier with 2 people.
Dispose of all packaging
.
carefully and responsibly.
care and maintenance
.Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
.Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
.From time to time check
that there are no loose
screws on this unit.
.This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.
Assemble on a soft level
.
surface to avoid damaging the
unit or your floor.
1
.This product has been produced
from natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
Assemble the item as close
.
to its final position (in the same
room) as possible.

Components - Panels
Please check you have all the panels listed below
2
01 Headboard (163,5 x 120cm) 04 Central Support (204,5 x 6cm)
05 Support Foot (29 x 6cm)
02 Footboard (163,5 x 43,5cm)
03 Side rails x 2 (200 x 11,5cm) 06 Slats x 24 (75,5 x 6,9cm)

2m
Components - Fittings
Please check you have all the fittings listed below
If you have damaged or missing components,
call the Customer Helpline: 03456 400 800
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(medium & large)
Eye protection
(when using a
hammer or glue)
Small
hammer
Ruler/tape
measure
3
E
D
16mm Screw x 08
40mm Wooden dowel x 04
A
110mm Bolt x 04
B
Half-Moon Nut x 04
F
35mm Screw x 48
G
50mm Bolt x 02
H
80mm L Shaped Bracket x 02
I
40mm Bolt x 02
J
Nut x 06 70mm Headless Bolt x 04
L
C
Allen key
M
Spanner
N
Washer x 04

Step 1
4
Fitting dowels
Insert dowels
into the indicated parts.
D
Assembly Instructions
D
D
D
D
D
03
03
Step 2
Assembling side rails:
Screw headless bolt1st:
to footboard .
2rd: Insert washers to
the side rails and fit
footboard to side rails.
Fix headless bolts using
nuts and spanner .
L
02
N
03
L
J
M
03
03
M
M
L
L
N
N
J
J
02
1st
2nd
02
Caution:
Assembling of
Step 2 and Step 3
will be easier with 2
people. It can also avoid
damages or brakes of any
part or component.

Step 3
5
Step 4
Assembly Instructions
Fixing support foot:
Fix support foot to
central support using
bolt and allen key as
shown.
05
04
GC
G
04
05
C
A
C
B
B
B
C
01
03
03
A
B
Assembling side rails:
Attach side rails to the
headboard. Insert half
moon nut into
side rails as shown.
Then fix them to the
headboard using bolts
and allen key .
03
01
B
C
A
03

Assembly Instructions
Step 5
Step 6
6
Fixing L shaped bracket:
Fix L shaped brackets
into pre-drilled holes in the
headboard and
footboard using screws
as shown.
E
H
01
E
E
E
H
E
01
Fixing central support:
Fix central support
to L shaped brackets in
headboard and
footboard using bolts
and nut as shown.
J
I
04
01
I
J
02
02
02
04
02

7
Step 7
Assembly Instructions
Step 8
Fixing slats:
Centralize s
lats in bed
frame prior to fixing. Fix
slats using screws as
shown.
Fix slats in one side first,
then fix them in the other
side by pushing the rail
against the slats if
necessary.
Periodically check that all
screws are tight.
F
F
Additional step to fixing
slats:
Warning!The screws that
attach the slatholders to
the sides never collide to
the screws that fix the slats
to the slatholders.
Warning!
collide.
Assemble is complete!