Argos 9x4 Gazebo With 4 Slide Panels User manual

@10 x Top Pole
I.
(6) 12 x Support Pole
I. y
<Cl10 x Leg Pole
I •.•.
I I
eEl 10 x Base Plate
9x4 Gazella Wi 11
J) 2 x End Panel
if ) 2 x Side Panel
•
•
(El 6 x Corner Joint
@9 x Centre Joint
~1xRoof
Fittings' .
43 14 x Long Peg @4 x Large Peg
'\ "","*1======;;;;))=
046xPeg
\
4j) 1 x Metal Bar
@60 x Canopy Ties
~
@54 x Wing Screw
V
Gl 4 x Ratchet Bell
~
C) 4 x Guy Rope
~
o 1 x Spanner
0_-9
IMPORTANT
. Read these instructions careful/yand _
familiarise yourself with the procedure
before assembling the unit
2 Check that you have all the component
parts following the list on the back
cover and familiarise yourself with
each part before proceeding
3 Take all the fittings out of the plastic bag
and separate them into their groups.
4. Ensure you have enough space to fay out
all the parts before assembly

Read all instruction before use and keep for future reference.
This unit is not a permanent fixture - Do not use or leave erect in
windy conditions.
Use fire safety in and around this tent and follow the Fire Precaution
Warnings.
After use allow to completely dry and follow the Care and Storage
guide.
Please note this unit is Shower Proof and not Waterproof.
A. Fire Precautions & Safety
This unit can 8urn, follow good Fire Safety at all times.
This Tent conforms to Grade 5 of 8S 6341.
Do not use naked flames in or around this unit - there is no Cooking
Area within this unit.
Do not store cooking apparatus, BBQs etc within this unit as it may
cause a hazard.
Do not smoke or allow smoking in or around this unit, try to locate this
unit at least 5-10 meters away from other campers where possible.
Choosing a Good Camp Site.
Orientate the Door away from prevailing winds to prevent the wind
blowing into the entrance.
Make sure the ground is level, free of debris, rocks and sharp objects
as these can damage the fabric, avoid pitching under trees but make
use of natural wind breaks such as hedge rows etc.
r:
A Tips and Guidelines.
Practice pitching and dismantling your tent before use and familiarize yourself with
the fittings and fixtures.
Take note of all the parts and fittings and ensure you don't forget anything when
leaving the campsite.
Before each trip check you have all the parts and fillings and check the fabric for
any damage.
Tents are prone to internal condensation when the air inside is warmer than
outside, avoid this by keeping the tent well ventilated.
Follow your Campsites Fire Safety Guide Lines.
Care and Storage
Take care when dismantling your tent and follow the instructions in reverse order.
Allow the Fabric and all parts to Completely Dry before repacking. Packing when
damp will cause mould and damage the fabric. We recommend unpacking when
you return home and allow to completely dry before re-packing and storing.
• Never Pull or Remove the tent pegs by the fabric fittings or guy ropes.
Carefully remove the poles from the sleeves to avoid damage to the seams.
All parts should be cleaned and packed separately, gently remove dirt and debris
from the fabric when completely dry with a soft brush. Never use cleaning abrasives
or detergents.
I

1. Fully insert Support Pole@ into
the Centre Joint @ and Corner
Joint~. Then use Wing Screws
@ to fix the Centre Joint @ and
Corner Jointi);) onto the Support
Pole@.
See fig. 1.
~
j •
fig.
NOTE: It would be useful to ask
someone to help you at this
stage.
1. Fully insert Top Poles@ into one
of the connecting frames. Then
use Wing Screws @ to fix the
Top Poles @ on the unit.
See fig. 4.
2. Firmly fit the other two connecting
frames to the unit. Then use Wing
Screws @to fix them.
See fig. 5.
fig.S
fig. 4
Connecting Frame
2. Use the same method as in fig 1
to fix the other 3 Support Poles
@ on the Centre Joints @ and
Corner Joint~.
See fig. 2.
3. Repeat steps 1 and 2 to assemble
two more connecting frames.
See fig. 3.
,
•
•
,
•
,
,
,
,
fig.
3
•
,
"
~
•
,
?
~
•
,
?
~
r
Connecting Frame
Connecting Frame

1. Use Wing Screws @ to fix 5 Leg
Poles@ on one side of the unit.
See fig. 8.
NOTE: It would be useful to ask
someone to help you at this
stage.
2. Use the same Canopy Ties @
as before to fix the top of the End
PanelsQ)onto the unit.
2. Unscrew the Nut and Screw from See fig. 9.
the Base Plate@.
~
See fig. 7.
~
•
•
•
fig. 7
•
3. Use the Nut and Screw to fix the 3. Use Wing Screws @to fix the
Base Plate@ontheLegPole@. other 5 Leg Poles ~ on the other
See fig. 7.
~
side of the unit.
See fig. 10.
•.......
/
'"
/
Nut
'"
Screw
1. Carefully locate the Roof @ on
top of the unit. Then use Canopy
Ties @to fix the Roof onto the
unit.
See fig. 6.
NOTE: It would be useful to ask
someone to help you at this
stage.

I
fig. 16
fig. 13
1. Secure the Gazebo by pegging
the Side and End Panels into the
ground using Pegs ~. Care must
be taken not to bend the Pegs.
use a rubber mallet If the ground
Is hard.
See fig. 13.
NOTE: It would be useful to ask
someone to help you at this
stage.
2. Use Long Pegs @to secure the
Base Plates on the ground.
See fig. 16.
3. Attach the ends of the Guy
Ropes Cj to the 0 rings on
Gazebo. Use Long Pegs @
to secure the other ends to
the ground.
See fig. 14 and 15.
fig. 11
Hook
Velcro Tape
fig. 12
NOTE: It would be useful to ask
someone to help you at this
stage.
1. Use the same Canopy Ties @
as before to fix the top of the Side
Panels Q3l onto the unit.
See fig. 11.
2. Use the Velcro tapes on the Side
Panels Q3l and End Panels Q)to
fix them on the Leg Poles.
See fig. 11.
3. Attach the Roofs Hooks into
holes on the Leg Poles. Tighten
by moving the Hook to a lower
hole.
See fig. 12.

~
;:>ernbly' Instructions
tage 7 - Fitting the Ratchet Bells
.•.. ~ -- ~.
Assembly;
Stage 8- Finishing the Unit
fig. 2
fig. 17
fig. 22
Safety
To avoid any risk of suffocation to animals or children dispose of the plastic
bags immediately.
Cleaning
As with all surfaces clean with a damp cloth and mild detergent, do not use bleach
or abrasive products.
After sales telephone number for spare parts. 0870 600 89 90
CAUTION: Do not Assemble or
Dissemble during strong winds.
1. Always zip up both doors when
you leave the Gazebo.
fig. 21
~
ll-< )
1. Attach one end of the Ratchet
Bell m to the uni .
See fig. 17 and 18.
NOTE: It would be useful to ask
someone to help you at this
stage.
2. Insert Metal Bar ( ) into top of
hole of the Large Peg @, with the
help of the Bar, rotate the Large
Peg into the ground at the desired
location.
See fig. 18 and 20.
3. Hook the other end of the Ratchet
Bell m onto the Large Peg @.
See fig. 18and 19.
4. Repeat steps 1 to 3 to attach the
other Ratchet Bells G).
See fig. 18.
5. Use the Ratchet on the Ratchet
Bells m to tension the canvas.
See fig, 21.
:----