Argos Sliding Gazebo 803/3914 User manual

Issue 1 - 26/05/10
Please read these instructions fully before starting assembly
Assembly Instructions - Please keep for future reference
Sliding Gazebo
803／3914
Important –
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800
Dimensions
Width - 300cm
Depth - 300cm
Height - 232cm

•Weight: kgs.
•
1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 & 3.
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product during assembly,
this could cause damage.
• Assemble the item as close
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
arbour or your floor.
• Parts of the assembly will be
easier with 4 people.
•
•
We do not
recommend the
use of power
drill/drivers for
inserting screws ,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
efully and responsibly.
Care and mainte nance
Please lift with care.
Warning: Take care when
operating or moving the unit.
•Only clean using a damp cloth
and mild detergent, do not use
bleach or abrasive cleaners.
•Make sure each screw
matches the corresponding
figure to ensure correct
assembly.
•From time to time check that
there are no loose screws on
this arbour.
•This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
•To prolong the life of this
unit, we recommend it is stored
inside during winter or extended
periods of bad weather.
58
car

Components - Parts
Please check you have all the parts listed below
Sliding top tube on two sides x2
Front horizontal tube x1
Back horizontal tube x1
Top tube x2
Sliding top tube in the middle x1
Leg tube x4
Left hanging fabric tube x1
Right hanging fabric tube x1
Left fabric tube x5
Right fabric tube x5
2
1
2
3
4
5
6
7
8
9
10

Components - Parts
Please check you have all the parts listed below
Footstand x4
Protection cover x1
Roof Cover x1
Components - Fittings
Note:
The quantities below are the correct amount to complete the assembly.
Ground pins x 16
15mm Screw x 14
Please check you have all the fittings listed below
l required
Ruler - Use this ruler to help correctly identify the screws
62mm Screw x 22 Metal washer x 39
Plastic cap x 39
15mm Screw x 10 32mm Screw x 3
Plastic cap x 10
3
11
12
13
ABC
DEF
G H I
13mm Screw x 14
K
JL
M
Spanner x 1
Allen key x 2
Tube cap x 8 Tube cap x 6

Assembly Instructions
Step 1
Assembly frame
Step 2
Use 16 mm screw
and metal washer
to fix footstand
to leg tube
Suggest to complete this
product assembly by four
persons.
.
4
A
E
6
13
then seal it
cap .
H
with plastic
Tighten the screw ,
A
13
6
3
5
5
3
A
6
H
E
53 &
Take the protective foams
away from two sides of
.
sliding top tube

Step 3
Step 4
use 13 mm screw to
fix it.
5
I
3
3
35
K
I
J
I
J
2
J
I
Assembly Instructions
5
1
J
J
J
2
Insert tube cap to the
5
&
K
sliding top tube ,
K
K
Insert tube cap to the
J
horizontal tube
1,use
13 mm screw to
I
fix it.
Step 5
Insert tube cap to the
J
horizontal tube
2,use
13 mm screw to
I
fix it.
1

Step 6
&
6
5
2
.
D
H
Tighten all the screw
and seal them with
plastic cap
4
J
4
I
2
1
3
3
4
45
2
1
345
&&
345
&&
E
H
D
H
E
D
Assembly Instructions
Insert tube cap to the
J
top tube
4,use 13 mm
I
to fix it.
Step 7
sliding top tube
on
Use 62mm screw and
metal washer to fix
D
E
top
tubes 4
3
horizontal
&
tube 1 .
screw

Step 6
.
E
7
Assembly Instructions
2
6
3
H
E
D
3
1
E
D
H
Use 62mm screw
and metal washer
to fix sliding top tube
on
Use 62mm screw
and metal washer
to fix horizontal tube
&on leg tube .
D
E
D
E
1 2 6
3
then seal it
cap .
H
with plastic
Tighten the screw
D,
leg tube .
6
6

Assembly Instructions
Step 9
E
7
12
2
7
7
2
C
H
8
ECHH
2
2
C
E
5
9
9
10
9
10
3
12
9 10
&
B
G
G
B
9 10
&
9
10
8
8
8
12
12
12
12
9
10
3
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6 Figure 7
Figure 8
Figure 9
Figure 12
Figure 11
Figure 10
Use 32mm screw and
metal washer to fix
hanging fabric tube &
to back horizontal tube
Use 15mm screw
to fix fabric tube &
on sliding top tube on two
sides , as Figure 11,
Connect fabric tube &
through sliding top tube in
the middle
C
E
7 8
2
B
9 10
3
9 10
5
Tighten all the screw C
and seal them with plastic
cap H.
Figure 4, Figure 5.
Figure 12.
.
B
G
Tighten all the screw
and seal them with
plastic cap
as
,
, as Figure 8
Figure 9 and
Connect fabric tube 8
7&,
as Figure 3.
Put fabric tube
&
into roof cover
12
78
&
&
9 10
，Figure 4, Figure 5,
as
Figure 6, Figure 7.
Figure 10.

9
Step 10
Use 15mm screw and
metal washer to fix
protection cover on
sliding top tube &.
Tighten all the screw
and seal them
cap .
A
E
11
3 5
A
with plastic
H
Assembly is complete.
Use ground pins
footstand into ground
if you want to firm this arbour.
to fix
F
13
Argos Limited
489-499 Avebury Boulevard Saxon Gate West Central Milton Keynes Bucks,MK9 2NW
If you need help or have damaged or missing p
For further assistance please visit http://www.argos-support.co.uk/
arts, call the Customer Helpline: 03456 400800
11
H
A
E
11
13
F
Assembly Instructions