Aries 1500302 User manual

ARIESAUTOMOTIVE.COM •PRODUCT SUPPORT: 877.287.8634 •1500302-INS-RA •10/10/2023 •ECN11186 •PAGE 1
Product Registration and Warranty
ARIES stands behind our products with industry-leading warranties. To get copies of the product
warranties, register your purchase or provide feedback, visit: warranty.curtgroup.com/surveys
INSTALLATION MANUAL 1500302
Parts List
Qty Description
1Front fender flare, driver side
1Front fender flare, passenger side
16 Button head bolts, 6mm x 25mm
16 Flat washers,
6mm x 12mm OD x 1.6 mm
16 Lock washers
16 Nut plates
1Hex wrench
Tools Required
Ratchet, 10mm Panel trim
removal tool
Phillips screwdriver --
Maintenance
Mild automotive detergent may be used to clean the product. Do not use dish detergent, abrasive
cleaners, abrasive pads, wire brushes or other similar products that may damage the finish.
Product PhotoLevel of Difficulty
Easy
Installation difficulty levels are based on time
and effort involved and may vary depending on
the installer level of expertise, condition of the
vehicle and proper tools and equipment.
NOTICE
Visit www.ariesautomotive.com for a full-color copy of this
instruction manual, as well as helpful videos, guides and much more!
Before you begin installation, read all instructions thoroughly.
Proper tools will improve the quality of installation and reduce the time required.
Periodic inspection of your product should be performed
to ensure all hardware and / or components remain secure.
To help prevent damage to the product or vehicle, refer to the specified
torque specifications when securing hardware during the installation process.
Torque Specifications
M6 bolt 6 ft-lbs.
Use above torque setting unless otherwise noted

ARIESAUTOMOTIVE.COM •PRODUCT SUPPORT: 877.287.8634 •1500302-INS-RA •10/10/2023 •ECN11186 •PAGE 2
PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY. ASSISTANCEIS RECOMMENDED.
1. Start installation on the Driver/Left side of the vehicle. Locate the (5) plastic clips attaching the fender to
the body of the vehicle, (Figure 1). Rotate counter clockwise to release the clips. Carefully pry the
fender away from the vehicle and place in a safe location, (Figure 2).
2. Locate the hardware attaching the fender liner to the outer edge of the wheel well. Temporarily remove
the hardware to access the backside of the fender location.
3. Select the Driver/Left Fender. With assistance, hold up the Fender to the mounting location. Determine
the holes needed in the body. Attach the holes in the Fender tothe body with (8) 6mm Button Head
Bolts, (8) 6mm Lock Washers, (8) 6mm Flat Washers and (8) 6mm Nut Plates, (Figures 3 & 4). Do not
tighten hardware.
4. Adjust the position of the Fender and fully tighten all hardware.
5. Repeat Steps 1—4 for Passenger/Right side Fender installation.
6. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
Driver/Left Side Installation Pictured
(Fig 1) Locate the (5) clips under the factory
fender, turn the clips counter clockwise.
Carefully pry the fender away from vehicle
Front
(Fig 2) Locate and temporarily remove
the hardware attaching the fender liner
to the edge of the wheel well
(Fig 3) Attach the front of
the Fender to the vehicle
(Fig 4) Attach the rear of
the Fender to the vehicle
Front
Front
(4) 6mm Hex Bolts
(4) 6mm Lock Washers
(4) 6mm Flat Washers
(4) 6mm Nut Plates
(4) 6mm Button Head Bolts
(4) 6mm Lock Washers
(4) 6mm Flat Washers
(4) 6mm Nut Plates