Aries 202020 User manual

PAGE 1 • 202020-INS-RC• 877.287.8634 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM
Product Image
Notes and Maintenance
Before you begin installation, read all instructions thoroughly.
Proper tools will improve the quality of installation and reduce the time required.
To protect the product, wax after installing. Regular waxing is recommended to
add a protective layer over the finish. Do not use any type of polish or wax that may
contain abrasives that could damage the finish.
For gloss black finishes, mild soap may be used to clean the product.
Refer to the table to the left when securing hardware during the
installation process to help prevent damage to the product or vehicle.
Level of Difficulty
Easy
Parts List
1Driver / left side bar
1Passenger / right side bar
2Mounting bracket, front
2Mounting bracket, rear
2Support bracket, front
8Hex bolt, M8 x 25mm
8Flat washer, M8 - 24mm x 2mm
8Lock washer, M8
4T-bolt, M10 x 50mm
2Hex bolt, M10 x 35mm
2Carriage bolt, M10 x 40mm
10 Flat washer, M10 - 27mm x 3mm
8Lock washer, M10
2Rectangular washer, M10
8Hex nut, M10 - 1.5
6Plastic bolt retainer, M10
Tools Required
Torque wrench Socket, 13mm
Extension Socket, 16mm
Wrench, 16mm Level
Scan
for helpful
install tips
Front
Rear
INSTALLATION MANUAL 202020
Torque Specifications
METRIC
M6 bolt 3 ft.-lbs.
M8 bolt 7 ft.-lbs.
M10 bolt 16 ft.-lbs.
M12 bolt 28 ft.-lbs.
SAE
1/4" bolt 3 ft.-lbs.
5/16" bolt 7 ft.-lbs.
3/8" bolt 16 ft.-lbs.
7/16" bolt 20 ft.-lbs.
1/2" bolt 28 ft.-lbs.

ARIESAUTOMOTIVE.COM • NEED ASSISTANCE? • 877.287.8634 • 202020-INS-RC• PAGE 2
Step 1
Starting on the driver-side, locate the two
mounting tabs underneath the vehicle.
Step 2
Locate the driver-side front mounting
point and remove the round and oval
rubber plugs.
Insert an M10 x 45mm carriage bolt
and an M10 rectangular washer into the
round hole. Slide a plastic bolt retainer
over the thread of the bolt to hold the
bolt in place.
Step 3
Insert an M10 T-bolt into the oval hole.
Slide a 9mm plastic bolt retainer over
the thread of the bolt to hold the T-bolt
in place.
Place the driver-side front mounting
bracket onto the vehicle and secure
the T-bolt with an M10 flat washer,
M10 lock washers and M10 hex nut.
Snug the hardware,
but do not fully tighten.
Step 4
Place the support bracket onto the
vehicle and secure to the carriage bolt
using an M10 flat washer, M10 lock
washer and M10 hex nut.
Align the slot on the support bracket
with the slot on the front mounting
bracket and secure using an M10 x 35mm
hex bolt and flat washer on the side
facing the front of the vehicle and a
flat washer, lock washer and hex nut
on the opposite side.
Snug the hardware,
but do not fully tighten

PAGE 3 • 202020-INS-RC• 877.287.8634 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM
Step 5
Locate the rear mounting point
and remove the oval rubber plug.
Insert an M10 T-bolt into the oval hole
and slide a plastic bolt retainer over
the threads to hold the bolt in place.
Place the driver-side rear mounting
bracket up to the vehicle and secure
the bracket to the vehicle using an M10
flat washer, lock washer and hex nut.
Snug the hardware,
but do not fully tighten.
Step 6
Place the side bar onto the mounting
brackets and align the mounting points.
Secure the side bar to the brackets using
four 10mm M8 x 25mm hex bolts, M8
lock washers and M8 lock washers.
Snug the hardware,
but do not fully tighten.
Adjust and level the side bar.
With the side bar in position, it is
recommended to tighten all brackets
to the vehicle first, followed by the
side bar connections.
Step 7
Repeat steps 1 through 7 on the
passenger-side of the vehicle.
Congratulations on the installation of
your new ARIES 3" round side bars.
With the side bars installed, periodic
inspections should be performed to ensure
all mounting hardware remains tight.
To protect your investment, see the
'Notes and Maintenance' section on
the first page of the instruction manual.