Aries 25630AB User manual

PAGE 1 • 25630AB-INS-RB • 800.798.0813 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM
Notes and Maintenance
Before you begin installation, read all instructions thoroughly.
Proper tools will improve the quality of installation and reduce the time required.
For black finishes, mild soap may be used to clean the product.
Level of Difficulty
Moderate
Scan
for helpful
install tips
INSTALLATION MANUAL 25630AB
Parts List
1Spare tire extension bracket
4Reinforcement bracket
8Clip nut, 8mm
8Hex head cap screw,
M8 x 1.25" - 40, CL8.8
2Hex head cap screw,
M8 x 1.25" - 60, CL8.8
8Flat washer, M8
8Lock washer, M8
3Nylock nut, 1/2" - 20, grade 5
Tools Required
Ratchet Vice grips
Socket, 13mm Wrench, 19mm
Product Image

ARIESAUTOMOTIVE.COM • NEED ASSISTANCE? • 800.798.0813 • 25630AB-INS-RB • PAGE 2
Step 1
Remove the spare tire from the factory
carrier. The factory-installed carrier
will also be removed to add additional
support brackets required for larger tires.
Begin removal by opening the rear door.
Step 2
With the rear door open, locate
the louvered plastic cover.
Use a flat blade screwdriver to remove
the cover, allowing access to the
electrical connection of the carrier-
mounted brake light.
Step 3
Disconnect the quick connect plug
running to the brake light.
Close the rear door and remove the
grommet securing the brake light wire.
With the grommet removed, pull the
wire and plug out of the door panel.
Step 4
With the brake light wire free, use a 13mm
socket to remove the eight hex bolts
securing the carrier to the rear door.
With the bolts free, lift the carrier off
of the vehicle and set to the side.

PAGE 3 • 25630AB-INS-RB • 800.798.0813 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM
Step 5
To install the new support brackets, the
factory weld nut must be removed.
Remove the louvered plastic cover that
was exposed when the carrier was
removed.
Locate one of the M8 x 60mm bolts in
the hardware kit and partially thread it
into one of the eight factory weld nuts.
Step 6
Clamp the back of the bolt with a vise-
grip for additional leverage and pry the
bolt up and down until the weld nut
breaks free.
Reach through access panel to grab the
weld nut and unthread the M8 bolt.
Repeat this for all eight nuts.
Step 7
Locate one of the reinforcement brackets
in the hardware pack.
Install two 8mm clip nuts over the ends
of the bracket.
Repeat this on all four brackets.
Step 8
With the clip nuts installed on the
brackets, align the flat side of the clip
nuts with the holes inside the door panel.
Have an assistant lift the tire carrier back
into position over the reinforcement
bracket and loosely install the M8 flat
washer, lock washer and 40mm hex bolt.
Repeat this for all four support brackets

ARIESAUTOMOTIVE.COM • NEED ASSISTANCE? • 800.798.0813 • 25630AB-INS-RB • PAGE 4
Step 9
With the 8mm fasteners reinstalled,
completely tighten all the hardware.
With the hardware tightened, re-install
the louvered panel inside the carrier.
Step 10
Thread the third brake light wire back
through the access hole and reinstall
the grommet removed in step 3.
Step 11
Open the rear door to access the wiring
panel and reconnect the brake light.
With the wire reconnected, replace the
louvered panel in the inside of the door
removed in step 2.
Step 12
With the carrier reinforced, the
extension bracket can now be installed.
Place the spare tire extension bracket
over the three factory lugs and secure it
with the supplied 1/2" - 20 nylock nuts.
Ensure all the hardware is completely
tight before reinstalling the spare tire.

PAGE 5 • 25630AB-INS-RB • 800.798.0813 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM
Step 13
Lift the spare tire back onto the three
mounting lugs and secure with the
factory lug nuts.
Finalize the install by confirming
all hardware and lug nuts are
completely tight.
Congratulations on the installation
of the ARIES tire relocation bracket.