ARJO HUNTLEIGH Aura User manual

Connect the pump to the mains power supply using the supplied cable.
Set the Run/Standby switch (on the side of the pump) to the Run ( |) position.
The Run/Standby indicator is illuminated when the pump is running.
In the event of mains failure, the Power Fail alarm indicator will start ashing and an audible alarm will sound.
The pitch of the alarm will increase in time. If the power supply is returned the audible alarm will stop, but the
alarm light will remain illuminated until the system is reset using the Run/Standby switch.
The Low Pressure indicator will ash whenever the pump detects low pressure in the cushion. An audible
alarm will sound. The pitch of the alarm will increase at 60 second intervals.
The indicator will extinguish once normal pressure is reached. Check the tubeset is connected properly.
Comfort Control - The seat cushion cell pressure can be manually adjusted for patient comfort using the
Pressure Control.
Note: An internal battery will power an audible and visual alarm if the power supply is interrupted prior to
switching off. For example, if the mains lead is removed before switching to Standby mode.
The pump alarm can be reset by switching the pump to Standby and back to Run again using the Run/
Standby switch on the side panel.
This Quick Reference Guide has been produced to assist Healthcare Professionals and other users with only the functional
aspects of the system. This guide does not replace the general safety warnings, cautions and recommendations provided in
the product Instructions for Use, part number 500935EN.
Refer to the product Instructions for Use before using this product.
Caution: Active therapy (alternating) cushions may be unsuitable for patients with poor sitting posture or pelvic deformity;
advice from a seating specialist should be sought.
Contraindication: Do not use the system for patients with unstable spinal fractures.
Caution: If patients have other unstable fractures, or conditions which may be complicated by a soft or moving surface,
advice should be sought from an appropriate clinician before use.
Indications:
• The Aura cushion is designed for patients weighing up to 120 kg (264 lb).
• The Aura systems are indicated for the prevention and/or management of all categories1of pressure ulcer, when
combined with an individualised, comprehensive pressure ulcer protocol.
1. NPUAP/EPUAP International Pressure Ulcer Guideline, 2014.
Aura
500937EN_03 · 05/2019
QUICK REFERENCE GUIDE
Aura

Installation
Place the Aura seat cushion on top of
the chair surface.
From a standing position in front of
the chair and facing it, make sure
the cells are uppermost, the tubeset
appears from the front right corner
of the cushion and the cells are in a
horizontal position across the chair.
Secure the seat cushion to the
chair surface using the xing straps
provided.
If the chair is of the closed side type
with a removable cushion, x the Aura
seat cushion as shown.
To complete the seat cushion installation:
Zip the protective cover over the cushion.
Make sure the Arjo logo is uppermost and at the front of the
cushion.
Quick Start:
When the Aura pump is switched on at the mains
supply, all indicators will momentarily ash.
Set the Run/Standby switch on the side of
the pump to the Run ( | ) position
Allow approximately 2 minutes for the seat cushion to
inate fully.
Once the patient is on the seat cushion, adjust the cell
pressures using the comfort control according to the
patient’s preference.
Caution: Do not use the seat cushion without a foam cushion
beneath it.
Installing the pump:
Position the pump feet down on any
convenient horizontal surface or
alternatively suspend from the chair
frame by means of swing out hooks.
Connect the male and female air feed
tubes into the appropriate outlets on
L
‘
‚
·¢
the pump unit. Push connectors in until they click. Make sure
the air feed tubes are not “kinked” or twisted.
Insert the mains power plug into a suitable mains power
socket.
Caution: Do not use the Aura seat cushion without a
foam cushion beneath it.
Caution: Always use the Aura seat cushion with the
protective top over.
Caution: Always use the Aura seat cushion in the correct
orientation.
Caution: Avoid trailing cables - ensure that cables and
tubing are positioned beneath the chair to
avoid causing a hazard.
Make sure the cells are in a horizontal position across the
chair, NOT from front to back.
® and ™ are trademarks belonging to the Arjo group of companies.
© Arjo 2019.
As our policy is one of continuous improvement, we reserve the right to modify designs without prior notice. The content of this publication
may not be copied either whole or in part without the consent of Arjo.
ArjoHuntleigh AB
Hans Michelsensgatan 10
211 20 Malmö, Sweden
www.arjo.com 500937EN_03: 05/2019