ARKSEN 002-AU-30035 User manual

Model# 002-AU-30035
OWNER’S MANUAL
35 Gallon Gas Caddy
!CAUTION! Do not use this device before reading these instructions.
CONTACT INFO
www.arksenusa.com
[phone]

2
Contents
GENERAL SAFETY 
IDENTIFICATION OF PARTS ---------------------------------------------------------
FIRST TIME INSTRUCTIONS ----------------------------------------------------------
03
04
06

3
INSTRUCTIONS PERTAINING TO THE RISK OR INJURY TO PERSONS.
IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
! DANGER
Gasoline and other fuels are extremely ammable. Keep away from heat sparks, and open ames as an explosion
will result in severe personal injury.
• Do not use electronics or mobile communications devices such as mobile phones while pumping ammable liquids.
• Attach ground wire and bond containers that are being pump from and into. Ground all containers to a known
ground source to dissipate static electricity before pumping liquids
• Gasoline vapors can explode. Harmful or fatal is swallowed. Avoid breathing fuel vapors
• Do not smoke near or while using this gas caddy.
• This product is intended for fuel transfer only and is not to be used to transport fuel in any vehicle or trailer.
• Do not modify this tank or product.
! WARNING
• When using this product basic precautions should always be followed, including the following;
1. Read all instructions before using this product
2. To reduce the risk of injury, close supervision is necessary.
3. Keep out of reach of children
4. Do not put ngers or hands into openings or into the pump
• Personnel should always wear proper personal protection equipment and clothing
• Ensure that all ttings and threaded hose and pipe connections are tightened and lead free.
! CAUTION
Not for prolonged storage of fuel.
• Use caddy for“one type of fuel only” to avoid possible damage to vehicle
• Monitor ow rate and ll levels to prevent overows and spills. Do not overll containers, drums or tanks.
• Always empty the pump and hose after use by lifting the hose and turning the handle in the opposite direction of
the arrow to empty all remaining liquids back into the caddy.
• Use caution when lling through the ll tube. Monitor closely to prevent overows and pills.
• Use care when maneuvering to prevent injury or loss of control. Seek assistance to avoid strain or
injury where required.
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT
It is the responsibility of the employer to place this information in the
hands of the operator. Keep for future reference.

4
IDENTIFICATION OF PARTS
Read the owner’s manual and safety instructions carefully before operating the gas caddy. Compare the illustration below to
the gas caddy in order to familiarize yourself with the location of the various controls and adjustments. Save this manual for
future reference.
A. Clamp
B. 3.5 M Plastic wire tube
C. Tube Connector
D. Earth wire with clip
E. Plastic nut
F. Fuel Measure gauge
G. Oil pump
H. Plastic dome
I. Metal Floater (inner the body)
J. Lock nut
K. 10’ solid rubber wheel
L. Wheel axel
M. Matel Washer
N. M18 cap nut
O. Matel Washer
P. M8 nut
Q. 3’ universal wheel with brake
R. M8*40 hex bolt
S. Oil Cap
T. Oil Filter
U. Handle
V. Steel body
W. Teon tape
X. Pump handle
Y. Foot
B Q
Y
X
K
P N
M
W
J
T
A
E
F
S
V
L
D
G

5
B
C
DJ
Y
K
N
X
V
Q
G
H
U
I
E
F
A

6
FIRST TIME INSTRUCTIONS
STEP ONE:
Tilt caddy frontwards (handle up). Take wheel axle and insert
018 washers to the end of wheel axle (see image below).
Insert the metal shaft to the caddy.
STEP TWO:
Put wheels on and follow with washers and cap nuts on the
wheel axel. Tighten cap nut with a wrench.
STEP THREE:
Remove the 3 red hex nuts from bottom of each side of
caddy. Attach the red foot and then re-screw the 3 red hex
nuts to each side.
STEP FOUR:
Take the 3” universal wheels with brakes and attach to the red
foot on each side. Take the (8) M8 Lock nuts and screw on to
each side so that wheels are secure. Tilt the caddy back to its
standing position.
STEP FIVE:
Take Teon tape and wrap tightly around the pump pipe 5-8
times. Screw on oil pump and use the wedge lock washer to
position pump and tighten.

7
STEP SIX:
Take Teon tape and wrap around the pump connector 5-8
times, wrapping tightly. Assemble oil tube to oil pump and
secure with clamp.
STEP SEVEN:
Attach pump handle to oil pump.
STEP EIGHT:
Take Teon tape and wrap around the thread of plastic
dome 5-8 times. Install fuel level gauge on plastic dome and
tighten.

8
STEP NINE:
Drop oil lter in the oil inlet and screw on the oil cap securely.
STEP TEN:
Attach handle to the caddy and lock into place.

9