ARKSEN 002-AU-30035/GAS35 User manual

Item# 002-AU-30035 / GAS35
Read carefully and understand all ASSEMBLY AND/OR OPERATION
INSTRUCTION before using the product. Failure to follow the safety rules
and other basic safety precautions may result in serious personal injury.
⚠WARNING! CAUTION!
35 Gallon Gas Caddy
OWNER’S MANUAL

owner’s manual
2
Thank you for purchasing our product.
This manual covers operation and maintenance information about the product. Read carefully and
understand all instruction before using the product.
All information in this publication is based on the latest product information available at the time of
approval for printing.
We reserve the right to make changes at any time without notice and without any obligation.
Table of Contents
03
04
06
Safety Instruction -----------------------------------------------------------------------
Parts and Features ----------------------------------------------------------------------
Assembly Guide --------------------------------------------------------------------------

owner’s manual
3
IMPORTANT SAFETY INSTRUCTION
READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING
When using this product, basic precautions should always be followed, including the following;
• This product is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning using the product by a person responsible of their safety.
• Do not use this product other than intended use.
• Wear proper protection equipment when installing or using this product.
• Ensure all ttings and threaded connections are tightened and leak free before operating.
⚠DANGER!
Gasoline and other fuels are extremely ammable. Keep away from heat sparks, and open ame.
• Do not use electronics or mobile communications devices such as mobile phones when pumping
ammable liquids.
• Attach ground wire and bond containers that are being pump from and into. Ground all containers
to a known ground source to dissipate static electricity before pumping liquids.
• Gasoline vapors can expode. Harmful or fatal if swallowed. Avoid breath in fuel vapors.
• Do not smoke near or while using the gas caddy.
• This product is intended for fuel transfer only and is not intended to be used to transport fuel in
any vehicle or trailer.
• Do not modify this product.
⚠WARNING! CAUTION! ATTENTION!
• Do not use this product for proplonged fuel storage.
• Use caddy for one type of fuel only to avoid possible damage.
• Monitor ow rate and ll level to prevent overows and spills.
• Always empty the pump and hose after using the caddy. Lift the hose and turn the handle to the
opposite direction to empty all remaining liquid back into the caddy.
• Caution when lling the cadde through the ll tube. Monitor closely to prevent overows or spills.

owner’s manual
4
PARTS AND FEATURES
A. Hose clamp
B. 3.5M Plastic wired tube
C. Tube connector
D. Earth wire with clip
E. Plastic nut
F. Fuel measure gauge
G. Oil pump
H. Plastic dome
I. Metal oater
J. Lock nut
K. 10” solid rubber wheel
L. Wheel axel
M. Metal washer
N. M18 cap nut
O. M8 nut
P. 3”universal wheel with brake
Q. Oil cap
R. Oil lter
S. Handle
T. Steel body
U. Pump handle
V. Foot
A
D
G
E
F
B
I K
L M N O
P Q
U V
R S

owner’s manual
5
A
D
Q
G
E
H
P
V
I
F
B
S
T
U
K
J
C

owner’s manual
6
ASSEMBLY GUIDE
STEP 1
Insert the wheel axle to the caddy. Put a washer to the end of the axle.
STEP 2
Put the rubber wheel to the end of the wheel axle. Secure it in place with washer and cap nut.
Repeat the same step for the other wheel.

owner’s manual
7
STEP 3
Remove the nuts from the bottom of the caddy. Attach the foot, then secure using the removed nuts.
STEP 4
Assemble the 3” universal wheel on the foot. Secure the wheels on the foot using M8 nuts.

owner’s manual
8
STEP 5
Screw the oil pump on the pump pipe. Make sure they are aligned before screwing to prevent cross
threading.
STEP 6
Screw the pump connector on the oil pump. Careful to prevent cross threading.

owner’s manual
9
STEP 7
Attach the pump handle to the oil pump.
STEP 8
Attach the wired tube to the connector. Secure it by tightening the hose clamp.

owner’s manual
10
STEP 9
Attach the plastic dome and fuel measure gauge to the gas caddy.
STEP 10
Insert the oil lter into the oil inlet, then cover it with the fuel cap.

owner’s manual
11
STEP 11
Attach the handle to the gas caddy and lock it in place.

owner’s manual
12
FINISHED