Armedica AM-SX Series User manual

This manual has been prepared for the owners and operators of the
ARMEDICA™ AM-SX Series Hi-Lo Treatment Tables, and contains
installation instructions, precautionary instructions and
maintenance procedures for the following model numbers:
AM-SX1000, AM-SX1060, AM-SX1072,
AM-SX2000, AM-SX3000, AM-SX3500,
AM-SX4000, AM-SX4500,
AM-SX5000, AM-SX5400
ISO 13485
FM 50089 .
Made in the U.S.A

AM-SX SERIES HI-LO TREATMENT TABLES
INSTALLATION
1. Remove all packaging material from the table.
2. There is no assembly required on the ARMEDICA™ AM-SX Series Treatment Tables.
3. Plug the power cord into a properly grounded 120 Volt AC outlet and follow the procedure outlined in the
Precautionary Instructions.
4. The tables are equipped with 4-total lock swivel casters for maximum stability.
5. The motors are equipped with a thermal cutout that protects them from overheating.
PRECAUTIONARY INSTRUCTIONS
1. Read, understand and practice the precautionary instructions in this manual. Be aware of the
limitations and the hazards associated with the ARMEDICA™ Treatment Tables.
2. The motor is double insulated for protection from EMI. This equipment has been tested and found to comply
with the limits for medical devices to the IEC 60601-1-2: Third edition 2007-03. These limits are designed to
provide reasonable protection against harmful interference in a typical medical installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to other devices in the vicinity. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to
other devices, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving device.
- Increase the separation between the equipment.
- Connect the equipment into an outlet on a circuit different from that to which the
other device(s) are connected.
- Consult the manufacturer or field service technician for assistance.
3. Always make certain all 4 casters are locked prior to patient use.
4. Always use both hands when changing the angle of any section of the
table.
5. Never change the angle of any section, except motorized sections, when the patient’s weight is on that
section.
6. Never place your hands or feet nor the patient’s hands or feet near any of the working mechanisms
of the table when raising or lowering the table.
7. Never leave patient unattended.
OPERATING INSTRUCTIONS
To adjust the height of the ARMEDICA™ Treatment Tables, a low voltage foot switch or hand switch is used to
activate the electric motor assembly. The up and down activators are clearly indicated by decals.
Duty cycle on/off Int. 1 min./ 9 min.
TABLE SECTION ADJUSTMENTS
The sections of the ARMEDICA™ Treatment Tables are raised by lifting them with both hands. The locking
mechanism holds them securely at any angle. To lower a section, hold it in one hand and release the locking
mechanism by rotating the lever with the other.
The AM-SX 4000 is equipped with an automatic spring return.
CAUTION: When lowering any of the table sections, make certain that your hands cannot come in contact with the
board supports.

CAUTION: When adjusting the non-motorized sections with the patient on the table, be sure that the patient’s
weight is not on the section you are going to adjust.
CAUTION: To adjust the arm rest on the 3-piece head section loosen knob while holding arm rest. Raise or lower
the arm rest to the desired position and tighten knob.
CAUTION: Make sure that each armrest on the 3-piece head section is locked securely in position before the
patient places any weight on it.
CAUTION: When locking the rolling section of the AM-SX 4000 in position, make sure the lock plunger is fully
engaged in one of the slots.
MAINTENANCE
The ARMEDICA™ AM-SX Series Treatment Tables are equipped with a maintenance free electric motor. The
moving parts of the table should have a drop of oil placed on them approximately every six months.
When lubricating the slide block track use a food grade grease.
Frequently check to make certain that all hardware (nuts, bolts, etc.) are properly adjusted and securely fastened.
In the event it becomes necessary to replace the foot switch, hand switch or the power cord, make certain that the
plug is properly installed and the locking tabs on the motor snaps in place.
The vinyl cover should be cleaned with mild soap and water and the table frame wiped with a dry cloth to remove
dust and lint when necessary.
SYMBOLS AND INDICATORS
Attention: Consult accompanying documents.
Type B Equipment: “An adequate degree of protection against electric shock is provided, particularly
regarding leakage currents and reliability of the protective earth connection.”
The grounding pin located on the power supply cable is for functional use only, and is present for
EMI/ EMC purposes. The motor is Class II equipment and does not rely on this grounding means for safety.
TROUBLESHOOTING
MOTOR DOESN’T WORK.
A. Check to see if motor is plugged into electrical outlet, and the power cord is properly plugged into the motor.
B. Make sure the electrical outlet has power.
C. Check hand switch or foot switch to be sure it is plugged in correctly.
D. Thermal cutout may have activated. Allow the motor to cool.
E. In the event there is a failure of the motor, the motor must be returned to Armedica Mfg. Corp. The motor must
be serviced by the manufacturer. Contact Armedica Mfg. Corp. prior to returning any parts or products to
obtain return authorization.
MOTORSPECIFICATIONS Lumbarsection(AM-SX3000&AM-SX5000models)
Magnetic Corp., Olney, Illinois 62450 Magnetic Corp., Olney, Illinois 62450
Model MAX 65-A200415A1001-000. Model MAX 30-B050265A10M0-000
Model MAX 63-A200415A0100-000. Rated Voltage and Frequency 120V 60HZ
Rated Voltage and Frequency 120V 60HZ. Current 1.8 Amps.
Current 1.8 Amps. Duty cycle: on/off Int. 1 min. / 9 min.
UL CORD SET 140-355
Duty cycle: on/off Int. 1 min. / 9 min.

1000 1060 2000 3000 3500 4000
1072 5000 5400 4500
1 18856 SX BASE FRAME 1 1111
2 13879 BRONZE BUSHING .630OD x .65Wx.1875 444444
3 02198 BUTTON HEAD SOCKET SCREW 1/2-13X3/4 444444
4 02012 SHOULDER BOLT M10X30 222422
5 03072 CASTER SWIVEL LOCK TENTE 444444
6 02176 BUTTON HEAD SOCKET SCREW 3/8-16X3/4 888884
7 18862 SX CASTER LEG ASSEMBLY W/HOLES 222222
8 02092 NUT NYLOCK M8-1.25 222422
9 03153 MOTOR MAX63 8000N (SX 3000 ONLY) 1
10 18858 DUAL LIFTING ARM 111111
11 18892 SINGLE LIFTING ARM 111111
12 02196 CAP NUT 1/2" 224866
13 02340 SX PLASTIC SLIDE BLOCK 444644
14 13855 SX PIVOT ROD 1/2x9 111111
15 02665 SCREW BTN HD SOC 7/16-14x1 444444
16 02553 PLASTIC FLANGE BUSHING .687ODx.510 ID 2444
17 02664 NUT ACORN 7/16-14 NICKEL PLATED 444444
18 14823 UPHOLSTERED BOARD 27x76 W/FACE HOLE 1
19 02312 TOP FRAME SX 1000 1
20 02042 BUTTON HEAD SOCKET SCREW 1/4 20x1/2 1
21 14826 UPHOLSTERED BODY BOARD SX 2000 1
22 14835 UPHOLSTERED HEAD BOARD SX SERIES 1111
23 02307 FRAME SX 3 PC HD SEC PNTD 11
24 13877 ROD SX 1/2x13.25 HEAD SECTION PIVOT 1111
25 02165 WASHER NYLON 1/2 ID 2223
26 13867 ROD SX 1/2x15-1/8 HEAD PIVOT 1111
27 18877 ROD SX 1/2"RDx8 HEAD SECTION SUPPORT 2222
28 02329 SX PLASTIC RELEASE HANDLE 2444
29 02543 PIN SPRING 3/16x1-1/2 2444
30 02663 WASHER LOC 7/16" INTERNAL TOOTH PLT 444444
31 18854 SX HANDLE LOCK BAR BENT 2444
32 13865 TUBE 3/4x6 LOCK SLEEVE 1222
33 02534 PIN SPRING 3/16x3/4 2444
34 02045 HEX HEAD CAP SCREW 1/4-20x1 8 14 12 18 20 22
35 02310 TOP FRAME SX 2000 1 1
36 14836 UPHOLSTERED CENTER BOARD SX 3000 1
37 14837 UPHOLSTERED FOOT BOARD SX 3000 1
38 18866 SX 3000 CENTER FRAME 1
39 18869 SX 3000 FOOT FRAME 1
40 14711 UPHOLSTERED CENTER BOARD SX 3500 1
41 14713 UPHOLSTERED FOOT BOARD SX 3500 1
42 02327 HINGE BENT 2.5x4 22
43 02503 RETAINER RING 1/2 EXTERNAL 226
44 13875 BAR HEX ROLLER LOCK RELEASE 1
45 03154 MOTOR MAX30 4000Nx50MM (SX 3000 ONLY) 1
46 18900 CENTER ARM SX 3000 1
47 02037 BUTTON HEAD SOCKET SCREW 1/4-20x1 4 444
48 13871 SX FOOT SUPPORT ROD W/BEND 222
49 13884 SX 3000 TOP PIVOT ROD 1/2x20-1/4 1
50 02325 HINGE SX F00T SUPPORT ROD PIVOT 222
51 18902 HINGE SX 3000 FOOT BOARD 2
52 03107 POWER CORD MAX65 MOTOR 8000N 111111
53 03106 FOOT SWITCH MAX65 8000N 111 11
54 03155 FOOT SWITCH MAX63 1
55 03105 MOTOR MAX65 8000N 120V 111 11
56 14840 UPHOLSTERED THORACIC BOARD SX 4000 1
57 02318 TOP FRAME SX 4000 1
58 18851 ROLLER FRAME SX 4000 1
59 14841 UPHOLSTERED LUMBAR BOARD SX 4000 1
60 14842 UPHOLSTERED FOOT BOARD SX 4000 1
61 02332 ANGLE SX ROLLER FRAME LOCK MOUNT 1
62 12743 BAR SX 1/8x1.5x7-5/8 TX ELBOW 2
63 02330 WHEEL SX TRACTION ROLLER FRAME 4
64 03084 NUT ROUND FLANGED 1/4-20x7/8 BARREL 2
65 02120 NUT HEX FIN 1/4-20 4
66 02100 NUT NYLOCK 1/4-20 11
PARTS LIST
ITEM NO. PART
NO.
DESCRIPTION QUANTITY
3

1000 1060 2000 3000 3500 4000
1072 5000 5400 4500
67 02501 SCREW PAN HEAD PHIL 10-32x1/2 4
68 02073 SCREW FLAT HEAD PHIL 1/4-20x1-1/2 2
69 03027 SPRING EXTENSION 2
70 03029 ROLLER FRAME LOCK 1
71 13869 ROD SX 1/2x14.563 TX ROLLER AXLE 2
72 02089 NUT NYLOCK 10-32 2
73 02185 SCREW FLAT HEAD PHIL 1/4-20x2 2
74 02060 SCREW FLAT HEAD PHIL 1/4-20x1/2 6
75 13912 TUBE RD 3/4x.120Wx9-15/16 SX 3PC HD 1 1 1
76 13910 BAR RD 1/2x11-13/16 SX 3PC HD 1 1 1
77 03113 HAND SWITCH MAX65 (OPTIONAL) 1 1 1 1 1
78 18883 SX 4000 MACHINE STAND 1
79 02050 HEX HEAD CAP SCREW 5/16-18x1-3/4 2
80 14508 ADAPTER BOARD 1
81 02090 NUT NYLOCK 1/2-13 1
82 03015 PLUG 1x2x14GA 2
83 03125 KNOB "T" SPRNG LOAD PULL PIN 1/4DIA 1
84 03008 PLUG 1x1-1/2 4
85 02162 SPACER PLASTIC .33 IDx.565 ODx.56 2 4
86 12751 SX 4000 STAND LOCK PLATE 1
87 28038 BRKT MACH STND MNT SX PNTD 1
88 03040 TORSION SPRING LESS BEND LEFT 1222
89 03030 TORSION SPRING LESS BEND RIGHT 1222
90 02508 BUTTON HEAD SOCKET SCREW 3/8-16X1 4
91 02555 LOCK COLLAR 1/2 ID 2222
92 14769 UPHOLSTERED HEAD CRESCENT HD 1
93 14767 UPHOLSTERED ARMREST CRESCENT HD 1
94 18906 HEAD FRAME CRESCENT HD 1
95 18898 LOCK SUPPORT CRESCENT HD 1
96 18896 LOCK BRACKET TUBE CRESCENT HD 1
97 02140 WASHER 1/4 4
98 14773 BD UPH SX 3 SEC HD 1 1
99 14774 BD UPH SX 3 SEC ARM 1 1
100 18783 FRAME ARM REST SUPPT PLTD 1 1
101 18779 BRKT ARM REST RIGHT PNTD 1 1
102 03075 KNOB W/STEM 1/4-20x1/2 2
103 03167 KNOB 5/16-18 1/2" L BLACK 1 3/4" 2 2
104 02509 SET SCREW CONE POINT 1/4-20X1/2 4
105 18787 BRKT LOCK SX 3PC HD SUPPT PLTD 2 2
106 18781 BRKT ARM REST LEFT PNTD 1 1
107 02105 NYLOCK NUT 5/16-18 2 4
108 13881 HANDLE SX LOCK ROD 1/2x11-13/16x60DEG 2
109 12461 ROD 1/2x7-1/8 1
110 03010 PLUG 1x1x14GA 44
111 02036 BUTTON HEAD SOCKET SCREW 1/4 20X3/8 2 2 2 2
112 02339 SX LOCK TAB 222
113 13908 BAR RD 1/2x12 SX 3PC HD PLTD 1 1
114 02078 SCREW PAN HD PHIL 10-32x3/8 2 2
115 18991 FRAME SX SIDE RAIL LEFT PNTRD 1
116 18993 FRAME SX SIDE RAIL RIGHT PNTD 1
117 18995 BRKT SIDE RAIL PIVOT MOUNT LR PNTD 1
118 18980 BRKT SIDE RAIL PIVOT MOUNT RR PNTD 1
119 02261 FRM SX CHANGING TABLE TOP PNTD 1
120 14853 BD UPH SX CHANGING TABLE 25x60 1
121 18998 BRKT SIDE RAIL PIVOT LOCK MNT LF PNTD 1
122 18982 BRKT SIDE RAIL PIVOT LOCK MNT RF PNTD 1
123 14859 BD UPH SX CHNG TBL SIDE RAIL 2
124 14869 BD UPH SX CHNG TBL 25x72 1
125 02104 WASHER 1/4" INTERNAL TOOTH LOCK 4
126 02657 PLUG RD 1"ODx14-20 GA BLK 4
127 02190 WASHER FENDER 1/4IDx1-1/4OD 2
128 18879 ROD SXDT THD'D FT LOCK BAR PLTD 2
129 02063 SCREW HX WASHER HD #10x3/4 8
130 02135 NUT HX FIN JAM 1/2-13 2
131 02111 NUT HX FIN JAM 5/16-18 2
132 03070 KNOB WING 1/2X13 ID 2
PARTS LIST
ITEM NO. PART
NO.
DESCRIPTION QUANTITY
4

30
13
5
6
1
7
15
12
14
53
3
17
9
52
10
4
8
11
54
77
55
SX BASE
5

3
1
2
AM-SX1060
AM-SX1072
47
117
118
116
119
122
120
121
123
115
34
124
127
128
125
126
AM-SX1000
AM-SX2000
21
34
31
28
35
16
12
89
32
33
27
26
88
24
23
22
6

7

8

50
47
48
130
111 129128
60
59
42
131
112
72
132
43
67
70
44
61
74
66
71
83
63
34
65
69
88
31
29
57
62
68
32
24
26
33
25
27
23
12
28
16
89
2
22
3
56
64
58
73
66
34
TOP FRAME
SX 4000
80
34
97
78
82
85
84
66
86
81 107
90
87
25
79
83
SWIVEL STAND
SX 4000
34
9

105 24
100
33
16
76
29
72
114
75
111
101
110
34
23
27
12
106
103
99
98
113
28
THREE PIECE HEAD
10

ARMEDICA™ MANUFACTURING CORP.
LIMITED WARRANTY
ARMEDICA™ Manufacturing Corp. warrants that the AM-SX Series treatment tables are free from defects in
material and workmanship. This warranty shall remain in effect for 18 months from the date of original
consumer purchase of the product. If the product fails to function during the warranty period due to a defect in
material or workmanship, ARMEDICA™ Manufacturing Corp. or the selling Dealer will repair or replace the
table without charge within a 30 day period from the date on which the table is returned to ARMEDICA™
Manufacturing Corp. or the selling Dealer. ARMEDICA™ Manufacturing Corp. has a policy of continuous
improvement that may result in changes to specifications at any time.
THIS WARRANTY DOES NOT COVER
1. Replacement parts or labor furnished by anyone other than ARMEDICA™,Selling Dealer or approved
ARMEDICA™ Service Agent.
2. Anyfailureofthetableduringthewarrantyperiodifthe failure is not caused by a defect in material or
workmanship or if the failure is caused by unreasonable use, including the failure to provide reasonable
andnecessarymaintenance.
ARMEDICA™ MANUFACTURING CORP. IS NOT LIABLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGE TO PROPERTY OR BUSINESS.
To obtain service under this warranty, please do the following:
1. A written claim should be sent to ARMEDICA™ Manufacturing Corp., P.O. Box 880, Greenwood, AR.
72936-0880 or the selling Dealer.
2. The table must be returned to ARMEDICA™ Manufacturing Corp. or the selling Dealer.
3. Thiswarrantygivesyouspecificlegalrightsandyou may have other rights, which vary from state to
state
ARMEDICA™ does not authorize any person or dealer to create for it any other obligations or liabilities in
connection with the sale of the tables. Any representation or agreement not contained in this warranty
shall be void.
Duty cycle: On/Off Int. 1 min./9 min.flammable anesthetics.
DANGER: Risk of explosion if used in the presence of
ARMEDICA MANUFACTURING CORP.
Lifting capacity 400 lb. (181 kg.)
Greenwood, AR 72936-0880
Serial No.
120 Volts 60 Hz 1.8 Amps
Model No.
!
PN 03410A
Medical Electrical Equipment
With respect to electrical shock,
Fire and mechanical hazards only
In accordance w/ UL 2601-1, IEC 60601-1
PN-03409 REV E 01/08/11
SX SERIES MANUAL