Ashcroft T5500 Instructions for use

IM-T5500/ATEX-EN-Rev C02/2016Page 1 of 21
P/N 095I103-02EN
Installation and Maintenance
Instruction Manual
Bourdon tube pressure gauge, model T5500 and T6500
for explosion risk areas pursuant to Directive 94/9/EC (ATEX)
In the following configuration:
•###T5500/T6500###ATEX bourdon tube pressure gauge without switching contact
•###T5500/T6500###I####ATEX bourdon tube pressure gauge with inductive proximity switch

Page 2 of 21
Table of contents:
1General remarks.........................................................................................................................................................3
1.1 Purpose of this Manual........................................................................................................................................3
1.2 Symbols...............................................................................................................................................................3
1.3 Limits of liability...................................................................................................................................................3
1.4 Copyright.............................................................................................................................................................3
1.5 Warranty..............................................................................................................................................................3
1.6 Manufacturer’s address, customer services........................................................................................................3
2Safety..........................................................................................................................................................................4
2.1 General sources of hazards................................................................................................................................4
2.2 Use in accordance with intended purpose..........................................................................................................4
2.3 Operator’s responsibility......................................................................................................................................4
2.4 Staff qualifications (target group assessment)....................................................................................................4
2.5 Signs/Safety markings.........................................................................................................................................4
2.6 Safety equipment ................................................................................................................................................5
2.7 Environmental protection.....................................................................................................................................5
3Use in explosion risk areas pursuant to Directive 94/9/EC (ATEX) ...........................................................................5
3.1 T5500/T6500 without switching contact..............................................................................................................5
3.2 T5500/T6500 I#### with inductive proximity switch KE##I##0C0H2 .................................................................5
4Technical data ............................................................................................................................................................6
5Labeling on the device................................................................................................................................................6
5.1 Labeling on the device for explosion risk areas (ATEX).....................................................................................6
6Construction and function...........................................................................................................................................7
6.1 Overview..............................................................................................................................................................7
6.2 Description of function.........................................................................................................................................7
6.3 Description of components..................................................................................................................................7
6.4 Accessories.........................................................................................................................................................8
7Transport ....................................................................................................................................................................8
7.1 Safety ..................................................................................................................................................................8
7.2 Transport inspection............................................................................................................................................8
7.3 Storage................................................................................................................................................................8
8Assembly/Installation..................................................................................................................................................8
8.1 Safety ..................................................................................................................................................................8
8.2 Preparations (requirements for the installation location).....................................................................................8
8.3 Mounting/Installation ...........................................................................................................................................8
8.4 Starting up...........................................................................................................................................................9
8.5 Subsequent relocation of the gauge (by the customer)....................................................................................10
9Servicing...................................................................................................................................................................10
9.1 Safety ................................................................................................................................................................10
9.2 Check on function, and recalibration.................................................................................................................11
9.3 Cleaning and maintenance ...............................................................................................................................11
10 Faults ....................................................................................................................................................................12
10.1 Safety.............................................................................................................................................................12
10.2 Conduct in the event of faults........................................................................................................................12

Page 3 of 21
10.3 Fault table......................................................................................................................................................12
10.4 Conduct following fault rectification ...............................................................................................................12
11 Removal, disposal.................................................................................................................................................12
11.1 Safety.............................................................................................................................................................12
11.2 Removal.........................................................................................................................................................12
11.3 Disposal.........................................................................................................................................................12
12 Appendix...............................................................................................................................................................12
12.1 Data sheet for Bourdon tube pressure gauge T5500/T6500.........................................................................12
12.2 Declaration of Conformity for device without switching contact ....................................................................13
12.3 Declaration of Conformity for device with inductive proximity switch............................................................14
12.4 Baumusterprüfbescheinigung (Gase) für Schlitzinitiatoren der Typen SJ KE##I##0C0H2 ..........................15
1 General remarks
1.1 Purpose of this Manual
This Operating Manual contains fundamental and essential advice to be followed for the installation, operation and
servicing of the device. It must be read without fail before assembly and start-up of the device by the fitter, the
operator and the specialist personnel responsible for the device. This Operating Manual must be available at the point
of use at all times.
The following sections about general safety information (2) and also the following specific advice regarding the
intended purposes (2.2) and through to disposal (11.3) contain important safety information which, if not followed, may
result in risks for people and animals, or to property and buildings.
1.2 Symbols
Warning!
This indicates a possibly hazardous situation where failing to follow advice may result in risks to people,
animals, the environment and buildings.
Information!
This emphasizes key information for efficient, fault-free operation.
1.3 Limits of liability
Failure to respect this safety information, the envisaged uses or the limit values relating to use indicated in the
technical data for the device may result in risk or to injury to people, the environment or the plant.
Claims for compensation for damage against the device supplier are excluded in such an eventuality.
1.4 Copyright
This Operating Manual may only be copied and passed on as a complete document without the special permission of
the publisher.
1.5 Warranty
For the product described here, we offer a warranty pursuant to Section 6 Guarantee in Respect of Defects in our
General Terms and Conditions of Delivery and Payment.
1.6 Manufacturer’s address, customer services
Ashcroft Instruments GmbH
Max-Planck-Strasse 1
D-52499 Baesweiler. Germany
Tel.: [phone]
Fax.: [phone]
E-mail: [e-mail]
Web: www.ashcroft.eu

Page 4 of 21
2 Safety
2.1 General sources of hazards
Pressure gauges are pressurized parts where failure can result in hazardous situations. The selection of pressure
gauge should be made in accordance with the rules set out in EN 837-2.
2.2 Use in accordance with intended purpose
The devices are only to be used for the intended purpose as described by the manufacturer.
The devices are used for direct display of overpressures, vacuum and compound pressure.
For each use scenario, the corresponding set-up regulations must be respected. If used in explosion risk areas, the
following conditions are to be respected for the individual finishes.
The integrated switching elements are inductive proximity switches with a groove design, supplied by isolating switch
amplifiers with certified intrinsically safe power circuits. If the set limit values are exceeded, the output circuits are
opened or closed.
2.3 Operator’s responsibility
Safety instructions for proper operation of the device must be respected. They are to be provided by the operator for
use by the respective personnel for installation, servicing, inspection and operation. Risks from electrical energy and
from the released energy of the medium, from escaping media and from improper connection of the device must be
eliminated. The details for this are to be found in the corresponding applicable set of regulations, such as DIN EN,
UVV (accident prevention regulations) and in sector-specific instances of use (DVWG, Ex-. GL, etc.) the VDE
guidelines and the regulations supplied by local utilities companies.
The device must be taken out of service and secured against inadvertently being restarted, if the presumption is that
risk-free operation is no longer possible (see Chapter 10: Faults).
Conversion works or other technical alterations to the device by the customer will violate the approval for
hazardous area and are not permitted. This also applies to installation of spare parts. Possible conversations
or alterations may only be carried out by the manufacturer.
The operational safety of the device is only guaranteed where it is used for its intended purpose. The specification of
the device must be adapted to the medium used in the plant. The limit values indicated in the technical data must not
be exceeded.
The safety information detailed in this Operating Manual, existing national regulations for accident prevention, and the
operator’s internal regulations regarding working, operations and safety must be respected.
The operator is responsible for all specified servicing, inspection and installation works being carried out by authorized
and qualified specialists.
2.4 Staff qualifications (target group assessment)
The device may only be installed and started up by specialist staff who are familiar with installation, start-up and
operation of the product.
Specialist staff are people who are able to assess the work assigned to them on the basis of their specialist training,
their knowledge and experience and their knowledge of the relevant standards, and can identify possible risks.
For devices in explosion-protected configuration, these staff must have been trained or instructed in, or be authorized
for, working on explosion-protected devices in potentially explosive plants.
2.5 Signs/Safety markings
The pressure gauge and its surrounding packaging carry markings. These markings show the article number,
measurement range and manufacturer. The pressure gauge can be provided with additional signs and safety markings
advising on special conditions:
Advice on the filling liquid
Advice on calibration
Safety marking pursuant to EN 837-1
Ex (for ATEX configuration)
Oil-can deleted (if oxygen is used)

Page 5 of 21
Silicone-free (for use in the automotive industry)
2.6 Safety equipment
This device is fitted with a rear wall or plug capable of being blown out. For a description, please refer to Chapter
6.3.4.
The window uses multi-layer safety glass.
2.7 Environmental protection
This device may optionally contain a filling liquid (e.g. glycerin or silicone oil). The provisions set out in the REACH
regulation on production and use of chemicals are to be respected, and the relevant safety data sheets from the
manufacturers of the chemicals are available on our website for download.
3 Use in explosion risk areas pursuant to Directive 94/9/EC (ATEX)
3.1 T5500/T6500 without switching contact
Area of use:
Explosion risk areas Zone 1 and 2, and 21 and 22, risk from gases and dry dust
Permitted temperatures:
Permitted ambient temperature -25°C to +60 °C.
Permitted medium temperature in the pressure gauge depends on the working conditions, not on the gauge design.
Warning! With gaseous media, the device temperature may increase due to compression heat. In
such cases, the rate of the pressure change must be regulated or the permitted temperature of the
measuring medium reduced.
Note:
To avoid additional temperature increase, the devices should not be exposed to direct exposure to sunlight when in
operation!
The effects of impact are considered as negligible.
For the non-electrical part of the devices, the standards EN 1127-1 (2007), EN 13463-1 (2009) and EN 13463-5
(2011) are applicable with regard to explosion protection. The relevant requirements of these standards are satisfied.
The documentation has been filed with TÜV-Nord-Cert (see declaration of conformity).
Labeling:
II 2 GD c IIC Tx
3.2 T5500/T6500 I#### with inductive proximity switch KE##I##0C0H2
Area of use:
Explosion risk areas Zone 1 and 2, risk from gases
Permitted temperatures:
The maximum occurring surface temperature of 95 °C was determined with no covering of dust and with no safety factor.
Permitted ambient temperature -25 °C to +49 °C.
Permitted medium temperature in the pressure gauge ≤45 °C.
Warning! With gaseous media, the device temperature may increase due to compression heat. In
such cases, the rate of the pressure change must be regulated or the permitted temperature of the
measuring medium reduced.
Note:
For a change in differential pressure between 10 % and 90 % of the measuring range and a pulse frequency of <
0.06 Hz, the temperature increase is <10 K.

Page 6 of 21
To avoid additional temperature increase, the devices should not be exposed to direct exposure to sunlight when in
operation!
EU design type test certification for the installed inductive proximity switches:
PTB 99 ATEX 2219 X
The integrated proximity switch is indicated on the type label/wiring diagram.
The surrounding housing has protection class IP65 as per EN 60529.
For use in explosion risk areas, the devices must be connected to certified intrinsically safe power circuits:
Max. voltage Umax = 16 V
Max. current Imax = 25 mA
Max. power Pmax = 64 mW
Device data (per contact):
max. internal capacitance Ci max = 30 nF
max. internal inductance Li max = 100 μH
The permitted limit values for Ui, Iiand Pifor the intrinsically safe feed power circuits depend on the proximity switch
type. They are to be found in the respective EU design type test certifications.
For the non-electrical part of the devices, the standards EN 1127-1 (2007), EN 13463-1 (2009) und EN 13463-5
(2011) are applicable with regard to explosion protection. The relevant requirements of these standards are satisfied.
The documentation for the mechanical part has been filed with TÜV-Nord-Cert (see declaration of conformity).
Labeling:
II 2 G c IIC T6 and PTB 99 ATEX 2219 X II 2 G Ex ia IIC T6 for the inductive proximity switch
Recommended isolating switch devices:
MTL 5011B 1-channel, for contacts/inductive proximity switch, operating voltage 20-35 VDC
MTL 5015 2-channel, for contacts/inductive proximity switch, operating voltage 20-35 VDC
KFA6-SR2-Ex1.W 1-channel, for contacts/inductive proximity switch, operating voltage 230 VAC
KFA6-SR2-Ex2.W 2-channel, for contacts/inductive proximity switch, operating voltage 230 VAC
4 Technical data
The detailed technical information can be found in the documents in the Appendix, Chapter 12.
5 Labeling on the device
The label with the serial number and type designation is located on the outside of the housing. The materials identifier
is encoded in the type designation.
5.1 Labeling on the device for explosion risk areas (ATEX)
The label with the marking for explosion risk areas is located on the outside of the housing.
Device without switching contacts:
###T5500####ATEX or ###T6500####ATEX

Page 7 of 21
Device with integrated inductive proximity switch
###T5500#### I####ATEX oder ###T6500#### I####ATEX
6 Construction and function
6.1 Overview
1 Bourdon tube
2 Socket and process connection
3 Movement
4 Pointer
5 Dial
6 Window
7 Bayonet ring
8 Gasket
9 Vent valve
10 Case
11 Blow-out and compensation plug
6.2 Description of function
The sensing element, a bourdon tube (C-form or helical) that is welded to the socket, will be exposed from inside with
pressure. Under pressure the elastic tube is deflecting against the zero position. This deflection is proportional to the
adjacent pressure. The movement transfers the deflection to the pointer.
The display of the measured value is given on a 270° scale.
6.3 Description of components
6.3.1 Scale with pointer
The pressure gauge is equipped with a dial face and pointer pursuant to EN 837-1, nominal size 100 mm or 160 mm.
Erläu ter ung, zusät zli ch ei n Hi n weis :
6.3.2 Instrument connection
The instrument connection is located on the bottom side (T5500 and T6500) or at the back side (T5500) of the
pressure gauge and is a threaded connection.
6.3.3 Vent valve

Page 8 of 21
The vent valve for the housing is located on the top side. If the nipple is pulled out, the housing is ventilated and the
pressure which has built up in the housing due to the influence of temperature is discharged. With the valve closed,
protection class IP 67 (for T6500 dry execution IP65) is achieved.
6.3.4 Rear wall / plug with blow-out capability
The pressure gauge has a plug capable of blowing out on the rear wall of the housing (Model T5500) or a rear wall
capable of blowing out (Model T6500). These act as a safety feature pursuant to EN 837-1 and simultaneously allow
for temperature compensation for the housing, via a rubber membrane.
6.4 Accessories
Please contact the manufacturer regarding special tools and accessories.
7 Transport
7.1 Safety
The pressure gauge should be protected against the effects of knocks and impacts. The device should only be
transported in the packaging provided, to protect against glass breakage. The device should only be transported in a
clean condition (free of residues of measuring media).
7.2 Transport inspection
The delivery must be checked for completeness and damage during transport. In the event of damage during
transport, the delivery must not be accepted, or only accepted subject to reservation of the scope of the damage being
recorded and, if necessary, a complaint initiated.
7.3 Storage
The pressure gauge must be stored in dry, clean conditions, within a temperature range of -40 to +70 °C, protected
against direct exposure to sunlight and protected against impact damage.
8 Assembly/Installation
8.1 Safety
To ensure safe working during installation and servicing, suitable shut-off valves must be installed in the plant (see 6.4
Accessories), enabling the device:
To be depressurized or taken out of operation;
To be disconnected from the mains supply for repair or checks within the relevant plant;
Or to enable function tests of the device to be performed “on site”.
During the works to mount/install the gauge, the plant must be protected against being switched back on.
8.2 Preparations (requirements for the installation location)
A check on suitability of the device for the medium to be measured, the scope of the measurement range and of
the protection against special conditions such as vibrations, pulsations and pressure spikes.
A bracket must be installed to support the pressure gauge if the metering pipe is not able to provide adequate
support.
Devices with a blow-out require a minimum spacing to the rear (20 mm).
The installation location should be chosen such that the work-spaces for operating personnel are not located to
the rear of the pressure gauge.
8.3 Mounting/Installation
8.3.1 Process connection
As standard, the device is equipped for pipework mounting with a pressure connection shank pursuant to DIN EN 837-
1. The device is calibrated ex works for vertical installation.
Connection to be undertaken by authorized and qualified specialist staff only.
Use only with the mechanical process connection provided – regarding the configuration, see order code on the
device type label, with a matching threaded seal.

Page 9 of 21
When connecting the device, the pipes must be depressurized.
The pressure metering pipe must be laid inclined in such a way that, for example, for measurements of fluids no
air pockets can form, and for measurements of gases no water pockets. If the necessary incline is not achieved,
then at suitable points water separators or air separators must be installed.
The pressure metering pipe must be kept as short as possible and laid without sharp bends, to avoid the
occurrence of irritating delays.
With liquid measurement media, the pressurized connection pipe must be degassed, since any gas bubble
inclusions result in measurement error.
If water is used as the measurement medium, the device must be frost-protected.
Safety notice: Only mount using the correct open-jawed wrench, and do not twist the device itself.
8.3.2 Electrical connection
Take note of the electrical data in the EU design type test certification and the locally-applicable regulations
and guidelines for installing and operating electrical plant in explosion risk areas (e.g. EN 60079-14, etc.).
Connection to be undertaken by authorized and qualified specialist staff only.
The electrical connection of the device is to be undertaken in accordance with the relevant regulations of the VDE
and the regulations supplied by the local utilities company.
Disconnect the plant from the mains supply before wiring electrical connections.
Install appropriate fuses upstream.
Please refer to type label
for configuration of
connections.
8.4 Starting up
The precondition for start-up is proper installation of all electrical feed lines and metering pipes. All connecting lines
must be laid such that no mechanical forces can act on the device.
Before start-up, the seal on the pressurized connection line must be checked.
8.4.1 Zero point adjustment
The pressure gauges are supplied calibrated ex works, so that as a rule there is no need for calibration works at the
installation point.
For devices with Micrometer pointer (see. order code), zero point adjustment on site is possible. For this, proceed as
follows:

Page 10 of 21
Depressurize the pressure metering pipe.
Open the bayonet ring and remove ring and window.
Hold the pointer in place while turning the screw, until the
pointer (after releasing again) has the correct position.
Close the case again and pay attention to correct fit of
window, gasket and bayonet ring.
Liquid filled gauges must be demounted before the zero
point adjustment can be done (on a horizontal area to
prevent leaking).
8.4.2 Setting the switch point
An adjustable lock is fitted in the front panel of the pressure
gauge. Using the removable adjustment key, the contacts
mounted on the target value indicators can be set to any point on
the range covered by the scale.
For reasons relating to accuracy of switching and the lifetime of
mechanical measurement systems, the switch points should be
positioned between 10% and 90% of the range.
Place the adjustment key on the axle of the adjustable lock.
Press the axle inwards, until the carrier arm grips behind the
adjuster pin on the target value indicator.
By turning the key, adjust the target value indicator to the
desired switch point.
Release the pressure on the axle, and remove the adjustment key.
8.4.3 Contact function
Function 1: Close contacts with the indication rising in a clockwise direction.
Function 2: Open contacts with the indication rising in a clockwise direction.
Contact assignment:
1st contact left target value indicator,
2nd contact middle target value indicator,
3rd contact right target value indicator
8.5 Subsequent relocation of the gauge (by the customer)
Recommendation: Do not remove the pressure gauge from one metering point and fit it in a different place,
as there is a risk of the measuring media being mixed, with unforeseeable chemical reactions.
9 Servicing
The device is maintenance-free. However, to ensure reliable operation and a long lifetime for the device, we
recommend that it is checked regularly.
9.1 Safety

Page 11 of 21
When undertaking servicing work on the device, the pressure lines must be depressurized and the plant secured
against being switched on again.
9.2 Check on function, and recalibration
The check on function and recalibration is carried out at regular intervals, depending on the application. The precise
testing cycles should be adjusted in line with the operating conditions and ambient conditions. In the event of various
device components interacting, the operating instructions for all other devices should also be taken into account.
Check on display.
Check on function, in conjunction with downstream components.
Check of pressurized connection pipes for seal condition.
Check of electrical connections.
9.3 Cleaning and maintenance
Cleaning is carried out using a non-aggressive cleaning agent, with the ventilation valve closed and respecting the
protection category of the device.

Page 12 of 21
10 Faults
10.1 Safety
Defective or faulty pressure gauges put the operational safety and process safety of the plant at risk, and can lead to a
risk or injury to persons, the environment or the plant.
10.2 Conduct in the event of faults
All defective of faulty devices must be taken out of service. If a repair is required, the device must be sent directly to
our Repairs Department. We request that all returns of devices are agreed with our Service Department.
10.3 Fault table
Possible situations indicating a fault:
Jerky or random movement of the pointer
Pointer does not set to zero for pressure less display
Bent or loose pointer
Cracked window
Leaks when the device is filled
Damage to housing
Indications that the measurement system seal is imperfect (discoloration to dial display or of filling liquid)
In these instances, replacement of the pressure gauge is always required.
10.4 Conduct following fault rectification
See Chapter 8.3Mounting/Installation
11 Removal, disposal
11.1 Safety
Residues of measuring media in and on removed gauges can constitute a risk to people, the environment
and equipment. Adequate precautionary measures must be adopted. If necessary, the devices must be
cleaned thoroughly (see advice in safety data sheets).
11.2 Removal
When undertaking servicing work on the device, the pressure lines must be depressurized, the electrical
connections isolated from the mains supply, and the plant secured against being switched on again.
Demount the gauge using a suitable tool
11.3 Disposal
Please help to protect the environment and dispose of or recycle the devices and components used in
accordance with the applicable regulations.
12 Appendix
12.1 Data sheet for Bourdon tube pressure gauge T5500/T6500
Detailed data sheet is available from supplier’s website (see 1.6 Manufacturer’s address, customer services)
This table refers to specific documents:
Model
Description
Document
T5500
Stainless steel pressure gauge model T5500
DS T5500
T6500
Stainless steel pressure gauge Solid Front design model T6500
DS T5500
T5500-KF
Stainless steel pressure gauge with inductive proximity switch
model T5500-KF
DS T5500-KF
T6500-KF
Stainless steel pressure gauge Solid Front design with inductive
proximity switch model T6500-KF
DS T5500-KF
T5500-KF
T6500-KF
Electrical contact devices for pressure and temperature gauges
G1.K55

Page 13 of 21
12.2 Declaration of Conformity for device without switching contact

Page 14 of 21
12.3 Declaration of Conformity for device with inductive proximity switch

Page 15 of 21
12.4 EU design type test certification (dusts) for inductive proximity switches of
types SJ KE##I##0C0H2

Page 16 of 21

Page 17 of 21

Page 18 of 21

Page 19 of 21

Page 20 of 21