Assa Abloy Rixson 1351 User manual

B
A
Slide "B" into "A"
866-474-9766 Technical Department
www.rixson.com
Model 1351
Max. Gate Size: 54" x 120"
Pull Side Mount ONLY
1Locate and mark closer mounting plate.
Using one aluminum slide track (B), insert it
into the closer mounting plate (A). This insures
the track will be in exact alignment to the closer
body. Mark the hole locations on the post.
IMPORTANT: Position (A) so the closer portion of
the plate will be mounted to the pull side of the gate.
Mount plate to post on pull
2side of gate. (Note that this
plate is not handed so it can be
mounted in either orientation.) Use
and holes for masonry post
mounting. Use and holes for
tubular post mounting. Attach (A) with
four hex screws. If the gate post is
masonry, use the longer screws with
the anchors included in the package. If
tube post extends above gate, use
masonry hole locations.
25mm
5.5mm 50mm
40mm
6mm
8mm
8mm
Tube Post
Masonry
Post
OS19510 (06-13)
1351 Gate Closer
ASSA ABLOY
RIXSON®
Hinge
Side
Masonry
Anchor
Push
Side
Closer Position
Tools Required
OS19510 (06-13)

FOR OPEN SPOKE GATE TOP
3Put the steel plates on either side of the
spokes. This will sandwich the spokes between
the two steel plates. Position the first screw of the
plate so that from the face of the post to edge of the
steel plate is approximately 7-7/8" (200mm ±10).
Using the supplied sex bolts and the larger screws
on the plates, attach as many mounting screws as
possible to secure the two plates to the gate spokes.
PAGE 2
FOR GATES WITH A TOP RAIL
Position the first screw of the plate so
that from the face of the post to edge of
the steel plate is approximately 8-1/2"
(215mm ±10). Using the sleeves
provided, secure the two plates to the top
rail of the gate.
Sex
Bolt
7-7/8" ±1/16"
Min. 13/16"
Max. 1-3/4"
Min. 13/16"
Max. 1-3/4"
8-1/2" ±1/16"
13/16"
Insert pin into guide.
5
On pull side of the gate attach only one side
4of 2 slide tracks to steel plates with 1 of 2 screws provided.
866-474-9766 Technical Department
www.rixson.comOS19510 (06-13)

PAGE 3
Insert guide with pin into open end of the
6track assembly.
DO NOT
PAINT
Attach second track end cap to steel plates
7with screws provided. It may be necessary to gently pull apart the two tracks allowing
room to insert the metal sleeve.
Attach surface closer to closer mounting
8plate on the post. Attach pin retainer
bracket to closer mounting plate and mount
closer with pins and screws.
Pin Retainer Bracket
Metal Sleeve
866-474-9766 Technical Department
www.rixson.comOS19510 (06-13)

PAGE 4
Attach arm to the pin in the guide.
10
Attach arm to closer spindle with
9screw and washer.
Make closer adjustments:
1- Closing Speed
2- Latch Speed
3- Closing Force
4- Backcheck Control
11
Snap on closer cover and cap.
12
ASSA ABLOY
RIXSON®
Rixson® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright© 2009, 2013, Yale Security Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
866-474-9766 Technical Department
www.rixson.comOS19510 (06-13)