Assa Abloy SW200 User manual

Original instructions
User Manual Entrance Systems
Swing Door Operator
ASSA ABLOY SW200

CONTENTS - Original instructions
3Instructions for safe operation .......................................................................................................
4Congratulations on your new automatic door! ........................................................................
4Electronic equipment reception interference ...........................................................................
4Environmental requirements ..........................................................................................................
4Product liability ...................................................................................................................................
5Warranty ................................................................................................................................................
5Service .....................................................................................................................................................
6Intended use .........................................................................................................................................
6Technical specification ......................................................................................................................
7How the ASSA ABLOY SW200 works ...........................................................................................
7ASSA ABLOY SW200 Variations ......................................................................................................
8Regular safety checks .........................................................................................................................
11General accessories ............................................................................................................................
11Safety accessories ................................................................................................................................
11Troubleshooting ..................................................................................................................................
12Service/Maintenance .........................................................................................................................
12Other products from ASSA ABLOY Entrance Systems ............................................................
13Declaration of conformity ................................................................................................................
ASSA ABLOY as word and logo are trademarks owned by the ASSA ABLOY Group
©ASSA ABLOY Entrance Systems, 2019
Technical data subject to change without notice.
Backtrack information: folder:Workspace Main, version:a528, Date:2019-06-10 time:11:24:38, state: Frozen
1009729-en-6.0Issue 2019-06-122

Instructions for safe operation
•Failure to observe the information in this manual may
result in personal injury or damage to equipment.
•To reduce the risk of injury to persons - use this oper-
ator with single or double pedestrian swinging or
folding doors only.
•Do not use the equipment if repair or adjustment is
necessary.
•Disconnect supply when cleaning or other mainten-
ance is to be carried out.
•The operator can be used by children over 8 years of
age if they have been instructed by a person in charge
of their safety.
•The operator can be used by children 8 years of age
or younger if they are supervised by a person respons-
ible for their safety.
•The operator can be used by persons with impaired
physical, sensory or mental capacity if they have been
instructed by a person in charge of their safety.
•Cleaning and user maintenance shall not be made by
children.
•Do not let anyone climb on or play with the door or
the fixed/remote controls.
•The doorset can be operated automatically by sensors
or manually by activators. It can also be used manually
as a door closer.
3Issue 2019-06-121009729-en-6.0

Congratulations on your new automatic door!
ASSA ABLOY Entrance Systems AB has developed automatic doors for more than 50 years. State-of-
the-art technology and carefully tested materials and components provide you with a superior
product.
As with all other technical products, your automatic door requires periodic maintenance and service.
It is essential that you know your automatic door (system) and that you recognize the importance
of maintaining it in compliance with applicable standards for safety.
Your local ASSA ABLOY Entrance Systems-authorized representative is familiar with these standards,
as well as all applicable local codes and ASSA ABLOY Entrance Systems recommendations for power-
operated pedestrian doors. Service and adjustments performed by your
ASSA ABLOY Entrance Systems-authorized representative, will ensure safe and proper operation of
your automatic door unit.
Electronic equipment reception interference
The equipment may generate and use radio frequency energy and if not installed and used properly,
it may cause interference to radio, television reception or other radio frequency type systems.
If other equipment does not fully comply with immunity requirements interference may occur.
There is no guarantee that interference will not occur in a particular installation. If this equipment
does cause interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
•Re-orient the receiving antenna.
•Relocate the receiver with respect to the equipment.
•Move the receiver away from the equipment.
•Plug the receiver into a different outlet so that equipment and receiver are on different branch
circuits.
•Check that protective earth (PE) is connected.
If necessary, the user should consult the dealer or an experienced electronics technician for additional
suggestions.
Environmental requirements
ASSA ABLOY Entrance Systems products are equipped with electronics and may also be equipped
with batteries containing materials which are hazardous to the environment. Disconnect power
before removing electronics and battery and make sure it is disposed of properly according to local
regulations (how and where) as was done with the packaging material.
Product liability
According to regulations, the following are the responsibility of the owner or caretaker of the
equipment
•that the equipment operates correctly, so that it gives sufficient protection in regard to safety
and health
•that the equipment is operated and regularly maintained, inspected and serviced by someone
with documented competence in the equipment and in applicable regulations
•that the provided “Service Log Book”and “Site Acceptance Test and Risk Assessment”documents
(PRA-0007) are kept available for maintenance and service records
•that inspection covers the emergency opening function (when applicable)
•that the closing force is appropriate for the door size on fire-approved door systems (when ap-
plicable)
1009729-en-6.0Issue 2019-06-124

Warranty
ASSA ABLOY Entrance Systems warrants its products to be free from defects in material and work-
manship under intended use and service for a warranty time of 12 months, beginning at time of
delivery. This warranty extends only to the original buyer of the equipment.
ASSA ABLOY Entrance Systems warrants that the software will operate substantially in accordance
with its functional descriptions and that it has been recorded on non-defective media.
The ASSA ABLOY Entrance Systems warranty does not apply to
•That the software will be error-free or operate without interruption
•General wear and tear on the system
•Fuse, disposable batteries and glass damage
•System deviations caused by installer other than ASSA ABLOY Entrance Systems
•System that has been altered or damaged by vandalism or misuse
•System that has been additionally equipped with non-ASSA ABLOY Entrance Systems original
branded parts and/or spare parts
•Unrequired visits due to poor client communication (door working when our technician arrives,
reset, power discontinuation)
•Adjustments (closing and opening speed and also detection field radars) due to customer re-
quests (excludes operational adjustments thought to create a hazard)
•Water damage
•Adverse weather conditions
•Any damage caused, directly or indirectly, by a circumstance beyond the control of the applicable
company within ASSA ABLOY Entrance Systems, such as industrial dispute, fire, natural disaster,
war, extensive military mobilization, insurrection, requisition, seizure, embargo, restrictions in
the use of power and defects or delays in deliveries by sub-contractors caused by any such cir-
cumstances
Please note:
•Non-compliance with manufacturers care and maintenance recommendations may void the
warranty.
•ASSA ABLOY Entrance Systems-authorized resellers shall extend this warranty to end-users only,
but have no authority to extend a greater or different warranty on behalf of
ASSA ABLOY Entrance Systems.
•A service agreement with ASSA ABLOY Entrance Systems will help secure the availability of a
fully operational system and will give priority at call-out, thus minimizing the time that the
equipment is unusable.
Service
Inspections should be done regularly by a trained and qualified person. The frequency of these
inspections should be according to national regulations (or according to industry standard if
there are no national regulations). This is especially important when the installation concerns
a fire-approved door or a door with an emergency-opening function. To extend the life of your
investment and ensure safe and reliable operation of the door, we recommend a minimum
of 2 visits per year or more, depending on usage and operating conditions. Environmental as-
pects shall also be considered.
5Issue 2019-06-121009729-en-6.0

As your entrances are part of your business flow, there’s every reason to keep
them working well. ASSA ABLOY Entrance Systems offers you a maintenance and
modernization expertise to rely on. Our Maintenance Programs and Modernization
Services for entrance automation is backed by a extensive expertise for all types
of pedestrian- and industrial door and docking systems, independent of brand.
At your disposal is a team of dedicated expert technicians, proven through decades
of maintenance, service and satisfied customers.
Intended use
The ASSA ABLOY SW200 is an automatic swing door operator developed to make life easier for
everyone who can benefit from automatic doors. The ASSA ABLOY SW200 is a low-energy operator
using a DC motor and a gear-reduction system to drive an arm system, which opens the door. It is
to be installed indoors where it is suitable for almost all types of external and internal swing doors.
This widely-used operator can be found in applications in health care, residential, office and public
buildings.
The door is designed to offer continuous use, a high degree of safety and maximum lifetime. The
system is self-adjusting to the effects caused by normal variations in the weather conditions and to
minor friction changes caused by e.g. dust and dirt.
For escape in emergency situations the doorset is opened manually.
For installation and maintenance see Installation and Service manual 1009728 for surface applied
installation and 1009936 for overhead concealed installation.
Save these instructions for future reference.
Technical specification
ASSA ABLOY Entrance Systems ABManufacturer:
Lodjursgatan 10, SE-261 44 Landskrona, SwedenAddress:
ASSA ABLOY SW200Type:
100-240 V AC +10/-15%, 50/60 HzMains power supply:
Max. 300 WPower consumption:
IP20Class of protection:
Sound pressure:
Third party approvals from established certification organizations valid
for safety in use, see Declaration of Conformity.
Approvals:
1009729-en-6.0Issue 2019-06-126

How the ASSA ABLOY SW200 works
The swing door operator ASSA ABLOY SW200 uses a DC motor which is connected to the output
shaft by a combination of a bevel gear and spur gears. The arm system that is connected to the output
shaft opens the door in a wall mounted application.
There is also an adjustable spring mechanism connected to the output shaft. During opening of the
door, the clock spring is tensioned by the rotation of the output shaft. During the closing cycle, the
accumulated spring force is acting in the closing direction. The spring force can be adjusted so there
is appropriate force to close the door when it is operated manually or in case of a power failure.
To activate the operator you can use a manual activator (elbow switch) or an automatic activator
(radar device). It is also possible –where local standards allow –to activate the operator by just
pushing the door, if Push & Go is selected.
After the door has been activated it will open and stay open for a specified Hold Open Time (HOT).
When the HOT has elapsed the door will close.
The ASSA ABLOY SW200 can be set in three or four different modes, depending on optional pro-
gramme selector type, see table below.
In fully manual use (or in case of a power failure) the ASSA ABLOY SW200 acts as a normal door
closer.
FunctionPosition
The door is closed. The door cannot be opened with inner and outer activation
units. The door is locked if an electromechanical locking device has been fitted.
The door can be opened with a key switch (if fitted).
OFF
Passage from inside only. The door is normally locked if an electromechanical
locking device has been fitted. The door can only be opened with the inner activ-
ation unit and with a key switch (if fitted).
EXIT
The door can be opened with the inner and outer manual and/or automatic ac-
tivators. The electric strike, if fitted, is open.
AUTO
Normal
position
The door is held permanently open by the motor.OPEN
ASSA ABLOY SW200 Variations
Surface applied application in 152 mm wide x 152 mm high headerASSA ABLOY SW200 -SA-
152X152:
OHC application in 152 mm wide x 152 mm high headerASSA ABLOY SW200 -OHC:
7Issue 2019-06-121009729-en-6.0

Regular safety checks
To help you fulfil the national/international requirements and to avoid malfunction and risk for in-
juries, we have provided the following checklist.
Do not use the operator if repair or adjustment is necessary.
Disconnect supply
14
when cleaning or other maintenance is to be carried out.
If problem
occurs
Daily Action
Activate your operator and check visually, fastening and any damage of
•operator
1
•arm system
2
•cables
3
•hinges
5
•door and glass
6
Also inspect your operator and check visually for
•sharp edges on the door leaf and door frame (if any)
7
•condition of door seals
8
•finger protection
9
•and finally that the complete door runs properly and closes slowly in a smooth way
Set the mode selector to OFF and check that the operator and electromechanical lock (if fitted)
work together. Also check that the lock
10
really secures the door.
Activate the manual activation units
11
, if any, and walk towards the door. Check that the door
has opened appropriately while you pass the entrance/exit.
Then proceed with the automatic activation units
12
in the same way.
Check the safety sensors
13
if any, by standing in the swing path and activate the operator. The
door must not hit you when opening nor when closing.
If you are unsure of which type of sensor you have, please contact your
ASSA ABLOY Entrance Systems representative.
Set the programme selector in AUTO mode. Push the door manually
in escape direction and make sure that no object or function will
prevent the door from opening. Also make sure the escape route is
free for use.
By law, these tests must be performed regularly by trained personnel.
Escape
doors
Let the door close after an impulse ensuring nothing prevents the
door from closing and locking (if regulations require it).
Fire
doors
Take appropriate measures.=
Contact your ASSA ABLOY Entrance Systems representative. For contact information, see last page.=
1009729-en-6.0Issue 2019-06-128

FUNCTION AND VISUAL INSPECTION
6
7
10
12
8
3
3
4
3
11
13
9
5
1
2 4
3
14
Surface Applied shown
CLEANING
The best way to remove dust and dirt from the ASSA ABLOY SW200 is to use water and a soft cloth or a sponge.
A gentle detergent may be used. To maintain the quality of the surface treatment, the surfaces should be cleaned
once/four months period. The cleaning should be documented. To avoid damages to the profiles the
brushes/weather stripping must be vacuum-cleaned weekly.
•Do not expose windows, doors or profiles to alkalis. Both aluminium and glass are sensitive to alkalis.
•Do not clean with high pressure water. Operator, mode selector and sensor may be damaged and water
may enter the profiles.
•Do not use polishing detergent.
•Do not scrub with materials like Scotch-brite, as this will cause mechanical damage.
9Issue 2019-06-121009729-en-6.0

SIGNAGE
Click!
Click!
800 mm
F
E
D
B
No entry
No entry
Keep clear
Keepclear
Automatic
door
Automatic
door
G
H
J
C
1100 mm
40 mm
ILL-01663
SITAC XXXX
TG XXXXXXX.
Ersätter lås med fallkolv till
typgodkända
slagdörrar enl. förteckning
Skydd mot olyckor vid
rörliga anordningar
K
DESIGNATIONART.NO.
YEAR+WEEK
1004083
XXXXXXX XXXXXXXXXXXXX
TYPE
XXXXXXXXXX
TEMPERATURE
XXXXXXXXXXXXXXX
LOAD
XXXXX
PROD.ORDER
XXXXXXX
XXXXXX
XX/XX
Hz
PROJECT/SERIALNO.
XXXXXXXXXX
W
XXXX
AVAC
ASSAABLOY Entrance Systems AB LODJURSGATAN10 LANDSKRONASWEDEN FACTORY NO. X
1 2 3 4 5 6 7 8
CLASSIFICATION DIN 18650-1:2010
xxxxxxx
xxxxxxx 1002
SÜD
Part of the Besam range
A
Surface Applied shown
If problem
occurs
Action
Check that all required signage is applied and intact. Mandatory indicates that the signage is re-
quired by European directives and equivalent national legislation outside the European Union.
Product label: Mandatory
A
Emergency break-out: Mandatory, if approved for escape route.
B
ASSA ABLOY Entrance Systems door sticker: Mandatory, if applicable to highlight the
presence of the glass (applied to all glass sections that are moving).
C
Supervision of child (applied to both sides of the door): Mandatory according to national
regulations. Recommended, if the risk analysis shows use by children.
D
Operator designed for disabled people:
Recommended, if applicable (applied to both sides of the door).
E
Activation by disabled people: Recommended, if applicable.
F
No entry, identifying one-way traffic: Mandatory in GB and US, if applicable, not included
in the product.
G
Automatic door
H
Keep clear
J
SITAC label: Mandatory in SE
K
Contact your ASSA ABLOY Entrance Systems service representative. For contact information, see last
page.
=
1009729-en-6.0Issue 2019-06-1210

General accessories
Your ASSA ABLOY SW200 can be further improved with the following add-ons (please contact your
local ASSA ABLOY Entrance Systems dealer for detailed description).
•Position switch
4
, see page 9
•Electrical lock
10
, see page 9
•Key switch
11
, see page 9
•Elbow switch
11
, see page 9
•Radar
12
, see page 9
•Wireless transmitters (not illustrated)
•Access control (not illustrated)
•Door stop (not illustrated)
Safety accessories
Even though the ASSA ABLOY SW200 is installed to comply with all applicable safety regulations, it
is possible to enhance safety/comfort with the following add-ons (please contact your local
ASSA ABLOY Entrance Systems company for detailed description).
•Safety sensors
13
, see page 9.
•Finger protection
9
, see page 9.
Troubleshooting
RemediesWhat´s wrong?
The door does not open
Change the setting of the mode selector.
(See page 7).
The motor does not start
Check that there are no objects in the detection zone if a sensor is
fitted.
Check the mains switch and fuse in the building.
Unlock the mechanical locks.The motor starts but door(s)
will not open Check that nothing is jammed beneath the door.
Change the setting of the mode selector.
(See page 7).
The door does not close
Check that there are no objects in the detection zone if a sensor is
fitted.
Check that nothing is jammed beneath the door.
Check that there are no moving objects within 1-1.5 m (39"-59")
from the door if an automatic activation unit is fitted.
The door opens and closes
continuously
If the problem continues, please contact your ASSA ABLOY Entrance Systems representative.
11Issue 2019-06-121009729-en-6.0

Service/Maintenance
Service and adjustments performed by your ASSA ABLOY Entrance Systems-authorized representative
will ensure safe and proper operation of your automatic door unit.
Remember to keep “Service Log Book”and “Site Acceptance Test and Risk Assessment”documents
(PRA-0007) available. These are used together.
The table below shows the recommended interval in months, when to replace parts during preventive
maintenance. Talk to your ASSA ABLOY Entrance Systems representative to learn more about our
service offering.
Abusive
Environment
Cycles/hour in operationPart numberPart
>100<100<10
High
traffic
Medium
traffic
Low
traffic
661224330000271 SI/BKPUSH arm service kit
661224330000272 SI/BKPULL arm service kit
661224330000276Stop arm kit
661224330000275Micro switch kit
661224330000270 SI/BKAdaptor kit
60606060331007291Transmission unit
60606060331008346Control unit CU-200 with EXU-
boards
2424242433738753Battery
Other products from ASSA ABLOY Entrance Systems
•Vertical lifting fabric doors•Door Systems
•Dock levelers•Balance doors
•Dock shelters•Air curtains
•Folding doors•Revolving doors
•High speed doors•Sliding doors
•Loadhouses•Automatic and manual activation units
•Overhead sectional doors
•Service such as preventive maintenance and upgrade programs, emergency repairs, service
advice and door management
1009729-en-6.0Issue 2019-06-1212

ASSA ABLOY Entrance Systems ABWe
Lodjursgatan 10
SE-261 44 Landskrona
Sweden
declare under our sole responsibility that the type of equipment:
SW200
complies with the following directives:
2014/30/EU ElectroMagnetic Compatibility Directive (EMCD)
2006/42/EC Machinery Directive (MD)
2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(RoHS)
Harmonized European standards which have been applied:
EN 60335-2-103:2015EN 60335-1:2012+A11:2014
EN 61000-6-3:2007+A1:2011EN 61000-6-2:2005
EN 16005:2012/AC:2015EN ISO 13849-1:2015
Other standards or technical specifications, which have been applied:
BVLBBR
UL 325FCC 47 CFR Part 15 B
IEC 60335-2-103:2002 ed. 1/2011 ed. 2.1IEC 60335-1:2010 ed. 5
EN 1634-1:2008
EC type examination or certificate issued by a notified or competent body (for full address, please contact
ASSA ABLOY Entrance Systems AB) concerning the equipment:
UL File E47833SC0072-14
UL File R9469
The manufacturing process ensures the compliance of the equipment with the technical file. The manufacturing
process is regularly assessed by 3rd party.
The CE mark was first applied 2013-11-04.
Compilation of technical file:
Email: [e-mail] Forslind
ASSA ABLOY Entrance Systems AB
Lodjursgatan 10
SE-261 44 Landskrona
Sweden
PositionSignatureDatePlace
Global Quality ManagerKlas Hagelin2019-06-04Landskrona
Declaration of conformity
DoC 1010491-en-6.0
13Issue 2019-06-121009729-en-6.0

ASSA ABLOY Entrance Systems is a leading supplier of entrance
automation solutions for efficient flow of goods and people. Building
on the long-term success of the Besam, Crawford, Albany and Megadoor
brands, we offer our solutions under the ASSA ABLOY brand. Our
products and services are dedicated to satisfying end-user needs for
safe, secure, convenient and sustainable operations.
ASSA ABLOY Entrance Systems is a division within ASSA ABLOY.
assaabloyentrance.com
ASSA ABLOY Entrance Systems
Tel: [phone]
[e-mail]
assaabloyentrance.com