Astral pool 66577 Instruction manual

Manual de instalación, operación y mantenimiento

Installations-, Betriebs- und Wartungsanleitung

Installation, operation and manteinance manual

Manuel d'installation, d'exploitation et maintenance

Manuale di installazione, operativo e manutenzione

Manual de instalação, operação e manutenção

EQUIPOS PARA FUENTES

FOUNTAIN UNITS

Made in

SPAIN

Wind Control Sensor

66577 Wind Control Sensor

66578 Wind Control Unit

Fig. 1

Fig. 2

 
3 
Fountain units 
[en] 
INSTALATION, OPERATION AND MAINTENANCE MANUAL 
Wind Control Sensor 
ÍNDICE 
1GENERAL SAFETY ...................................................................................................................................................................................4 
1.1 ELECTRICAL SAFETY ......................................................................................................................................................................4 
1.2 SAFETY IN USE......................................................................................................................................................................................4 
1.3 OPERATION AND MAINTENANCE SAFETY ....................................................................................................................................4 
2INSTALATION AND ASSEMBLY ..............................................................................................................................................................4 
2.1 SENSOR FASTNING AND LEVELLING .....................................................................................................................................................4 
2.2 CONTROL UNIT FASTENING ....................................................................................................................................................................5 
2.3 WIRING DIAGRAM ..................................................................................................................................................................................5 
2.4 SETTINGS.............................................................................................................................................................................................6 
2.5 CONTROL UNIT OPERATION DIAGRAM....................................................................................................................................................11 
3OPERATION AND MAINTENANCE ........................................................................................................................................................11 
3.1 SAFE MANAGEMENT OF WASTE.............................................................................................................................................................12 
4TECHNICAL SPECIFICATIONS ..............................................................................................................................................................12 
5FAQS ........................................................................................................................................................................................................12 
6PRODUCT LABELLING...........................................................................................................................................................................12 
7WARRANTY .............................................................................................................................................................................................12 
 
 

1GENERAL SAFETY

1.1 ELECTRICAL SAFETY

-Disconnect the unit from the power supply before doing any assembly or maintenance job.

-Do not touch the water or get into the water while the unit is connected to the power supply.

-Connect the unit to a power supply with an earth connection, protected by the following components:

An RCD safety switch with a maximum residual current of 30 mA.

A circuit breaker fuse for 10 A current.

1.2 SAFETY IN USE

-The anemometer installation must be under the following conditions:

Anemometer

characteristics

Minimum value

Maximum value

Temperature

-20°C

80 °C

Measuring range

2 m/s

55 m/s

Accuracy

+- 2 m/s

Output

Accuracy

0…210 Hz, a 55m/s = 200 km/h

0.26 m

Weight

0.154 kg (sin

cable)

1.265 kg (con

cable)

Protection class

IP 65

-In case of frost and -20ºC or bellow temperatures, remove the unit to avoid breakage.

-Do not handle the enclousures, otherwise the unit could lose its warranty.

1.3 OPERATION AND MAINTENANCE SAFETY

-Do not handle any component beyond the current manual instructions.

-Don not handle the unit with wet hands.

-The unit may only be handled by authorised personnel or qualified service engineers. Do not allow unauthorised personnel or unqualified

service engineers to handle it.

2INSTALATION AND ASSEMBLY

IMPORTANT:

-Read the whole of the manual carefully before installing the unit.

-Upon receiving the product, check that the unit is in good conditions.

-Identify all components prior to their installation.

2.1 SENSOR FASTNING AND LEVELLING

Necessary components fixing the unit:

Components

Qty

Plastic straps

Adequate fasteners

Bracket support

1) Fix the anemometer to the desired surface using fasteners:

IMPORTANT: Level the anemometer in order to ensure a proper operation:

Place it at a minimun height of 10 metres, a clear area without any obstructions around and exposed to wind.

Ensure the perpendicularity to the floor of the sensor, the wire must be set to any surface in order to avoid damage caused by high

wind speeds. (Fig. 3)

Fountain units

Fig. 3

IMPORTANT: Prevent any friction or oxide slags that could damage the wire cover.

2.2 CONTROL UNIT FASTENING

IMPORTANT: Risck of damage. Fix the control unit out of the fountain within a enclosure or electrical cabinet. The protection class of the

control unit is IP-20.

A DIN rail is provided with the unit for assembling in the electrical cabinet.

2.3 WIRING DIAGRAM

Connect the sensor to the terminals Y1 and Z1. The output will be connected to terminals 15-18 / 25-28 / 35-38 of the control unit, depending

on the relay whose operation would be required, relay 1 (R1), el relay 2 (R2) o el relay 3 (R3) respectively. (Fig. 4)

Fig. 4

1) Connect main power supply (230 V AC) to the terminals A1 and A2 of the control unit. (Fig. 5) If the connection has been made

correctly, the green LED must be on.

Fig.5

Plastic strap

Wire

Plastic strap

Bracket support

Support profile

2.4 SETTINGS

The control unit has a display to visualize the values of wind speed, as well as a set up menu for the output activations in function of the wind

detected by the anemometer.

NAVIGATION BY MENUS

To navigate by the menus and realize the set up, the control unit has three keys:

-▲▼Keys to navigate through menus and modify values.

-● Key to enter and exit menus, and validate the introduced values.

RELAY STATE CONFIGURATION

SET UP MIN/MAX WIND SPEED

Fountain units

SET UP MIN/MAX WIND SPEED VALUES

SET UP DELAY ON DETECTION AND/OR ON RELEASE

A practical example of control unit setting is given below.

Let us assume that there is an installation where our objective is to decrease the pump flow when the wind is between 10 Km/h and 20 Km/h

and for winds faster than 20km/h, switching the unit off to prevent equipment damage and for safety reason.

For this, there is one anemometer and one control unit, that unit will be set following below control parameters:

-Relay 1 will be disabled if wind is faster than 10km/h during 5 seconds of detection time.

-Relay 1 will be activated again when wind is slower than 8 Km/h during a release time longer than 5 seconds.

-Relay 2 will be disabled if wind is faster than 20 km/h during 5 seconds of detection time

-Relay 2 will be activated again when wind is slower than 15 km/h during a release time longer than 5 seconds.

Note: In this case, both relays Will be set as NC.

Control unit setting:

Relay 3

In this case, Relay 3 is not necessary, then, it will be set as out of order, thus both minimum and maximum configurable wind speed must be

disabled.

Procedure:

-Press the key with a circle.

-Press the arrows to reach Relay 3 and press the circle´s key.

-Press the arrows until Definition working mode and press the circle´s key.

-Press the arrows to reach Wind speed minimum and press the circle´s key.

-Press the arrows to reach Operative and press the circle´s key.

-Press the arrows to reach Return and press the circle´s key.

-Press the arrows to reach Wind speed detection minimum and press the circle´s key. Type 0.0 and validate.

-Press the arrows to reach Wind speed release minimum and press the circle´s key. Type 0.1 and validate.

-Press the arrows to reach Definition working mode and press the circle´s key.

-Press the arrows to reach Wind speed maximum and press the circle´s key.

-Press the arrows to reach Non operative and press the circle´s key.

-Press the arrows to reach Wind speed minimum and press the circle´s key.

-Press the arrows to reach Non operative and press the circle´s key.

Fountain units

How to change the anemometer release set point in explained below.

Relay 1 (Strong wind)

This relay´s role is to detect strong gusts of wind. It will be set this way:

-Press the key with a circle.

-Press the arrows to reach Relay 1 and press the circle´s key.